Antennas
any structure or device used to collect or radiate electromagnetic waves.
See Also: Broadband Antennas, Log Periodic Antennas, Directional Antennas, HF Antennas, Biconical Antennas, Horn Antennas, Isotropic Antennas, Loop Antennas, Antenna Software, Antenna Analyzers, Dipole Antennas, Transmitters, MIMO
-
Product
GPS / GNSS Antenna Signal Splitters
-
INSTOCK Wireless Components, Inc
INSTOCK Wireless GPS Signal Splitters are available in 2-way thru 48-way configurations spanning 1-2 GHz with unpeered performance in GPS (L1-L5), GNSS, Galileo, GLONASS, BeiDou, and IRNSS antenna splitting applications. The 200 ohm internal load on the DC-blocked port(s) prevents receivers from incorrectly sensing an antenna fault when there is no current draw. Type N, SMA, TNC, BNC, and QMA connector configurations INSTOCK.
-
Product
TURBO-TENNA 137 MHz Weather Satellite Antennas
WX-137 SERIES
-
The WX-137 series of antennas are marine-grade 137 MHz circularly polarized antennas designed to receive weather satellite images from the polar orbiting NOAA and Meteor satellites. Manufactured from stainless steel and ABS plastics, the assemblies are sealed and designed to survive marine service, although they may be used on land as well. Each antenna is available with or without a gasfet preamplifier which provides about 16 dB of gain and is physically located adjacent to the antenna.
-
Product
GPS/GNSS Antenna Signal Splitter 4-Way, TNC Female, IP67 Weatherproof, 1-2 GHz
GPS421
-
INSTOCK Wireless Components, Inc
GPS421 is a four way, passive, GPS signal splitter ideal for splitting a GPS antenna signal between two receivers while providing a DC current path to power a remotely located active GPS antenna from one receiver while blocking the DC path from the other. Furnished with TNC female connectors all ports. A special feature of this unit is the 200 ohm internal load which provides a current drain for the GPS receiver not powering the active antenna. Some GPS receivers incorrectly sense an antenna fault when there is no current draw. The 200 ohm internal load provides a simulated antenna current drain which prevents receiver faulting. Max voltage rating at the DC blocked ports is 15 VDC; maximum current rating is 75 mA. Max voltage rating at the DC pass port is 50 VDC; max current rating is 2000 mA.
-
Product
Antennas
-
Kyocera AVX Components Corporation
Antennas by Kyocera AVX - standard and custom antennas, active antenna solutions, and measurement systems
-
Product
Fanless Embedded System With I.MX 8M Processor, COM, LAN, USB, DIO (2-in/2-out), 2 PCIe Mini Card Slots, Optional CANBus, Power Design With ACC Ignition And E-Mark Certification For Vehicle Box PC
Agent336
-
The Agent336 is a RISC-based fanless embedded box PC certified with E-Mark for a variety of in-vehicle applications. The Agent336 measures only 164 x 118 x 44 mm and weight about 1.0kg. The cost-efficient embedded computer can withstand harsh operating environments with a wide operating temperature range of -40°C to +70°C and power input of 9 to 36V DC. This low power yet high-quality In-vehicle box computer is powered by the NXP i.MX 8M processor with the ARM® Cortex™-A53 microarchitecture and has a 3GB onboard LPDDR4 memory. Concerning the reliability and durability, the Agent336 comes with intelligent power management for ACC on/off delay, shutdown delay and over/under voltage protection. It runs on Linux (Yocto) and Android 8.1 operating systems. This IP40-rated RISC-based embedded gateway with strict certification is definitely the top choice for in-vehicle solutions, such as devices controller, fleet management, surveillance, and gateway. The newest RISC-based Agent336 supports two RS-232/422/485 ports, one isolated DIO, one HDMI port, two USB 3.0 A-type ports, one console port, one Gigabit LAN port, one RTC battery, one reset button, and five antenna openings. One onboard 8GB eMMC and one Micro SD card socket are available for extensive storage needs. Additionally, the rugged embedded computer has high integration ability with two full-size PCI Express Mini Card slots and one SIM card, which makes it a professional embedded system for transportation applications.
-
Product
Horn/Notch Antennas
-
Horn and Notch Antennas perform well over wide bandwidths while providing directive radiation patterns and moderate gain levels. CAES offers an extensive range of products including conical, pyramidal and sectoral horn antennas, as well as dual-polarized, high-power tapered notch antennas.
-
Product
Cellular Antennas (5G, LTE, CBRS, 3G, 2G)
-
Our internal and external cellular antennas cover 2G, 3G, 4G ,5G, LTE, CBRS and 5G NR frequency ranges for fixed and mobile applications.
-
Product
Antenna Test Chamber
-
Comtest provides Antenna test ranges fully covered with microwave absorbers for both near-field and far-field measurements. Because we always strive for new solutions, our R&D department developed our ‘Javelin Tip’ polystyrene absorbers. The enhanced material composition and altered shape, lead to improved performance and cleaner working space, enabling you to make high precision antenna testing fast, reliable, and worry-free.
-
Product
Tripods For EMC
-
These tripods are a great choice for EMC testing. They are made of non reflective nylon and wood material. The antenna height can be easily adjusted by moving the center slotted rod up or down. The tripods are designed to be portable, so that the antenna can be placed at the appropriate location for testing. The legs can be folded for easy transport and storage.
-
Product
3 DB 180 Degree Hybrid Couplers
-
KRYTAR's 180 Degree Hybrid Couplers offer wide frequency coverage in single, compact packages which provide low insertion loss, high directivity and tight coupling. These hybrid couplers offer simple solutions in many applications within those frequency bands including electronic warfare (EW), commercial wireless, SATCOM, radar, signal monitoring and measurement, antenna beam forming, and EMC testing environments. For many space-restricted situations the compact size of these KRYTAR couplers are ideal. These couplers can be also be manufactured to meet military specifications.
-
Product
Fanless Embedded System With Intel® Celeron® J1900, HDMI, VGA, 2 GbE LAN, 4 USB, 3 COM And 10 To 34 VDC
eBOX626-842-FL
-
The eBOX626-842-FL is the energy-efficient fanless embedded box PC suited for rugged and extreme applications with its extended temperature and wide range voltage capability. The extreme compact box PC utilizes an onboard Intel® Celeron® quad core processor J1900 2.0GHz (codename: Bay Trail-D) to boast both excellent performance and ultra-low power consumption. The ultra-slim fanless embedded computer supports system memory up to 8 GB with one DDR3L-1066/1333 SO-DIMM socket and offers HDMI and VGA display outputs, offering not only high computing capability but also excellent graphics performance. Integrated single-chip design, the brand new ruggedized embedded system is lighter and thinner compared to previous eBOX620 series. Supporting wide operating temperature between -20°C to +55°C and 10 to 34VDC wide DC input voltage, the fanless embedded PC is excellence for wide range of industrial applications. Its passive cooling design also offers quiet, fanless operation with low power consumption, and all at an attractive price point. With full-featured of I/O interfaces, the Intel® Celeron®-based eBOX626-842-FL supports two RS-232/422/485 ports, one RS-232 port, VGA, HDMI, audio, dual Gigabit Ethernet LAN ports, four high-speed USB 2.0, three SMA type connector openings for antenna, 10-34VDC power input connector, and one ATX power switch. One 2.5" SATA HDD drive bay and mSATA are also embedded in the embedded computer to possess sufficient storage.
-
Product
Vector Network Analyzer Extenders
VNAX
-
VDI''s VNA Extenders deliver high performance network analyzer frequency extension into the THz range. Models cover 50 GHz to 1,100GHz with additional bands in development. VDI modules come in a variety of form factors and configurations including our original Standard-size Modules and new Mini Modules that reduce volume up to 75%. In addition to our full Transceiver (TxRx) modules, VDI also offers Transmit-Reference (TxRef) modules and Receive only (Rx) modules that deliver optimized performance for specific applications. These modules combine high test port power and exceptional dynamic range to deliver industry leading performance. They are compatible with most network analyzers and can be integrated into probe stations and antenna chambers.
-
Product
CAMI® Broadband AM Isocouplers
-
LBA Technology’s CAMI® series of new-concept low, medium, and high power broadband isolators are the modern way to mount additional antennas on “hot” AM towers. These broadband colocation systems offer a simple, economical solution to take full advantage of existing vertical real estate. The LBA CAMI® isocoupler family supports any combination of RF carriers from DC to 2700 MHz or more, and conservative RF power levels to 40,000 watts at FM.
-
Product
Ka-Band Silicon 5G Quad Core IC
AWMF-0108
-
The AWMF-0108 is a highly integrated silicon quad core IC intended for 5G phased array applications. The device supports four Tx/Rx radiating elements, includes 5 bit phase and 5 bit gain control for analog RF beam steering, and operates in half duplex fashion to enable a single antenna to support both Tx and Rx operation. The device provides 26 dB gain and +9 dBm output power during transmit mode and 28 dB coherent gain, 5.0 dB NF, and -28 dBm IIP3 during receive mode. Additional features include gain compensation over temperature, temperature reporting, Tx power telemetry, and fast beam switching using eight on-chip beam weight storage registers. The device features ESD protection on all pins, operates from a +1.8 V supply, and is packaged in a 48 lead 6x6 mm QFN for easy installation in planar phased array antennas.
-
Product
L-Band RF Tuner and 2-Channel 200 MHz A/D with Virtex-6 FPGA - 6U VPX
Model 57690
-
- One L-Band tuners accept RF signals from 925 MHz to 2175 MHz- One programmable LNAs boost LNB (low-noise block) antenna signal levels with up to 60 dB gain- One programmable analog downconverters provide I + Q baseband signals with bandwidths ranging from 4 to 40 MHz- Two 200 MHz 16-bit A/Ds- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Model Vector Network Analyzer
DZV-1
-
Digital Signal Technology, Inc.
DZV-1 is the vector network analyzer which can be measured the impedance and VSWR of the antenna, S Parameter of RF component and devices. It is small and low-priced. So, it is suitable for the production line, laboratory use, various testing applications, and the educational use. The communication between the DZV-1 unit and PC is done via USB, which is also used for power supply. The LOG-MAG characteristic, the phase-characteristic, the group delay frequency characteristics, the Smith chart, the polar coordinates, the SWR characteristic can be displayed on PC.
-
Product
Antenna, Omni-Directional Wideband Discone
EM-6105 | 10 KHz – 2 GHz
-
The EM-6105 is a broad band collinear array allowing very wide Omni-Directional frequency coverage in a single package. Below approximately 100 MHz, the EM-6105 acts as an active vertical rod which offers 10 to 12 dB more signal handling capability than competitive antennas (overload field strength: 2 V/meter) which greatly reduces intermodulation generated signals in a typical read world RF environment. In the congested spectrum above 100 MHz the antenna is passive and contributes no intermodulation products so the overload point is determined solely by the receiving instrument. This immunity to overload can often make the difference between useful signal output and an indecipherable jumble of spurious products and is accomplished without compromising sensitivity. The antenna collapses for convenient storage and transport. The EM-6105 is supplied with an EM-6106 Battery Pack.
-
Product
SafeOne RF Safety Monitor
-
The SafeOne is a RF Safety Monitor covering the requirements set forth in WHO ICNIRP specifications. It has a very wide frequency range covering 30MHz to 10GHz, which makes it suitable for use in almost all antenna installations. Due to the innovative lightweight design, technicians can wear this at all times, without the need to constantly be observant of the state of the instrument. The SafeOne is powered with standard batteries, with 250 days of continuous operation.
-
Product
Terahertz Systems
-
Optoelectronic Terahertz-Generation. TOPTICA provides complete systems and components for both time-domain and frequency-domain terahertz generation. For time-domain applications, the TeraFlash sets new standards in terms of dynamic range, bandwidth and measurement speed. Combining TOPTICA's FemtoFiber smart laser technology with state-of-the-art InGaAs antennas, the system achieves a peak dynamic range of more than 90 dB and a bandwidth greater than 5 THz.
-
Product
3D/2.5D Time-Domain Electromagnetic Field Solver Software
EM-CORE ®
-
3D/2.5D Time-Domain Electromagnetic Field Solver Software for Planar-Circuit and Antenna Simulation. 3D & 2D Radiation Patterns Modeling, Spiral Inductors Modeling, 3D EM Modeling of Filters, Intuitive Geometry Build, and more!
-
Product
Antenna Switch
SixPak
-
The SixPak has two components: a relay matrix and a control box, there are several options for the controller.The relay matrix allows the selection of any 6 antennas by 2 radios or feedlines. Its lockout circuitry prevents both radios from selecting the same antenna. (The 6x1 type of SixPak is now replaced by our RatPak remote 6 way antenna switch.)The usual set-up has one SixPak dual rotary control box, which is manually operated from the radios positions. The control box for the 6x2 contains two rotary switches and 12 LEDs, so the operator can see which antennas are selected.
-
Product
Robust RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, 2 COM, 2 LANs And DIO (2-in/1-out)
IFB122
-
The IFB122 is an extremely compact RISC-based DIN-rail industrial IoT gateway powered by the low-power Freescale i.MX 6UL-2 processor in the ARM® Cortex™-A7 micro architecture. Designed to meet the challenges in critical environments, it supports extended operating temperature ranging from -40°C to 70°C, flexible wide voltage range 9V - 48V DC power input, and can withstand vibration up to 5G. One PCI Express Mini Card slot, one SIM card slot, and two internal antennas are available for Wi-Fi and 3G/4G connections. With the abilities to transmit data and manage various devices, the IP40-rated ready-to-run IFB122 is definitely a cost-effective solution for remote control/monitoring management applications such as unmanned control room, industrial machine, automatic parking lot, traffic cabinet, etc.
-
Product
Antenna Tuning Unit
MS 2012
-
Antenna Tuning unit is used to automatically tune the notch antenna impedance. Microprocessor does tuning through tuning inbuilt algorithm. It has RS485 interface for external control unit interface. Capacitor unit (CU), Inductor unit, (IU) and RF Element are subunits of this antenna-tuning unit. System maximizes transmission.
-
Product
AM Antenna Tuning Units
ATU's
-
LBA medium wave AM Antenna Tuning Units (ATU) and Line Tuning Units (LTU) are impedance matching units designed to match the transmitter to the impedance of the transmission line or the antenna system. Our Antenna Tuning Units are available for both series-fed and {ln:Tunipole antenna systems} Tunipole™ antenna systems to powers in excess of 500 kW.
-
-
Product
AA Neon Tube Tester
-
West Coast Custom Designs, LLC
When the antenna is touched to the tubing wall or electrode wires, the tester will cause the viable tubing to illuminate in a pulsating manor. This pulsing feature is fantastic for testing neon in bright sunlight as it is easier to see the light when flashing.
-
Product
Log Periodic Antenna
ZDS7-1-6G-832
-
Log Periodic Antenna, Frequency 1~6GHz, Gain 9dBi, VSWR 2.5, Linear polarization, N-Female
-
Product
Attenuators
-
The National RF line of attenuators are compact, affordable attenuators which are ideal for insertion between a direction finding antenna and a receiver/transceiver, to aid in the DF process. In addition, they may be used in the laboratory for a low-power, in-line attenuation purposes. The affordable price is achieved by utilizing standard 5% tolerance resistors and commercial hardware. For laboratory purposes, an attenuation versus frequency curve (to 500mMHz) is provided.
-
Product
Three Loop Antenna
VVLA-30M
-
The three loop antenna VVLA-30M is a standard measurement antenna according to CISPR15-2005/GB17743-2007 standard
, it can work with LISUN EMI-9KA / EMI- 9KB EMI Receiver System for EUT magnetic field radiation measurement between X, Y and Z planes. The antenna measurement is accurate, switch conveniently and it can completely replace imported products. -
Product
Accessories
-
Advantech In-vehicle accessories include vehicle mounting solutions, integrated mounting holes, cameras and antennas. The vehicle mounting accessories are ideal for vehicle mounted and securing mobile data terminal (MDT) to moving vehicles. In addition, Advantech provides customized services to support the diverse needs for in-vehicle and panel mounting computer integration
