-
product
Quantitative Analysis Software
Electron Probe X-Ray Analyzer (EPXA)
The software runs on standard PC’s and operating systems (Windows XP and later). Complete ZAF analysis is possible, with or without standards, using an internal database of fundamental parameters (FP) such as absorption coefficients, fluorescence yields, transition probabilities, etc. There is also an integrated spectrum display.
-
product
FPGA Test System
DO-254/CTS
DO-254/CTS™ is a fully customized hardware and software platform that augments target board testing to increase verification coverage by test and satisfy the verification objectives of DO-254/ED-80. The target design runs at-speed in the target device mounted on the custom daughter board. The simulation testbench is used as test vectors to enable requirements-based testing with 100% FPGA pin-level controllability and visibility necessary to implement normal range and abnormal range tests. The FPGA testing results are captured at-speed and displayed using a simulator waveform viewer for advanced analysis and documentation.
-
product
Impedance Analyzer
6632
Frequency range: DC, 10Hz to 1/3/5/10/20/30MHz/50MHz. Basic accuracy up to ±0.08%. Automatic Level Control (ALC). Output impedance 25Ω/100Ω, switchable. Equivalent Circuit Analysis . Built-in DC Bias voltage ±12V. Ultra-high measuring speed < 3ms. Built-in the Dielectric constant-εr. Built-in the Permeability-μr. Support PC Link Software.
-
product
Parameter & Device Analyzers, Curve Tracer
Precision Current-Voltage Analyzer Series ensures accurate and efficient current-voltage measurements that give a clear insight into IV characteristics across a wide range of applications. The powerful characterization software and integrated source and measurements units (SMUs) make it much quicker and simpler to obtain accurate IV characterization. The EasyEXPERT group+ software supports all the characterization tasks such as measurement setup and execution, data analysis, data management and ...show more -
product
FTIR Exhaust Gas Analyzer Direct Measurement Type
FTX-ONE-CS/RS
The FTX-ONE offers a 5Hz sampling rate and simultaneously measure the concentrations of multiple components including NH3, CH4, and CO2, from (engine) direct exhaust gas using the Fourier Transform Infrared (FTIR) method in combination with multivariate analysis algorithm.
-
product
Analysis System
Neptune (EDS-WDS)
By integrating Energy Dispersive Spectroscopy (EDS) and Wavelength Dispersive Spectrometry (WDS) analytical techniques on a single platform, Neptune provides the power and flexibility of EDS with the resolution, precision, and detection limits of WDS. Together the two techniques extend X-ray microanalysis capabilities and provide solutions to the most challenging analysis problems. Each technique can be used independently or the data can be integrated to provide results which were previously unachievable.
-
product
Multiplex Optical Maintenance Meter
LS280
LS280 is used to measure optical maintenance factor for high power LEDs, LED module, LED bulb or other LED luminaries. It is the important measuring equipment for performing the reliability of illuminants. • Freely set the time interval and time extent for automatic measurement • LCD Display, connect with PC via RS232 and English version software. • The test results can export Excel or PDF format and easy to compare. It can be saved by LS280 software or by USB directly. • The engineer can do LE...show more -
product
Real-time Spectrum Analysis up to 510 MHz, Optimum Detection, Multi-touch
N9030B-RT2
See, capture, and understand elusive signals as short as 3.57 s with 100% POI and a complete set of advanced triggers View signal dynamics with integrated real-time displays Maximize your investment by adding RTSA at a fraction of the cost of a dedicated solution Easily integrate the 89600 software and thoroughly analyze complex signals Industry-leading 3 year warranty Every spec verified, adjustments included Lock in support & peak performance from the start
-
product
EPM and EPM-P Series Power Meter
The EPM and EPM-P Series provides high-performance, programmable power meters for CW, average and peak power measurements. EPM Series: measure average power over a range -70 dBm to +44 dBm, and over frequency range 9 kHz to 110 GHzEPM-P Series: measure peak, average and time-gated power over -65 dBm to +20 dBm, to 18 GHz using E932XA power sensors. It provides complete pulse and statistical analysis with PC software via the GPIB or RS232
-
product
VME Intelligent Interface Card
IIB-3910-VME
The IIB-3910-VME is a single slot (6U) intelligent interface card providing complete STANAG 3838 and STANAG 3910 test, simulation and bus analysis capability for the VME Bus.
-
product
Digital Refractometer for Glucose
MA873
Thousands of food and beverage professionals and hobbyists, from chefs and food quality professionals and beverage manufacturers have moved to digital Glucose measurement from less accurate and less precise optical refractometers for sugar analysis.
-
product
Secondary Ion Mass Spectrometry (SIMS Analysis)
Rocky Mountain Laboratories, Inc.
Secondary ion mass spectroscopy is operated either in the dynamic mode (DSIMS) or the static mode (SSIMS). DSIMS is useful for profiling impurity and trace elements through films and interfaces. SSIMS is useful for characterizing polymeric materials and only measures the outermost molecular layer of a specimen.
-
product
Single, Dual or Quad Stream MIL-STD-1553A/B Test and Simulation Module
APE1553-x
MIL-STD-1553 Test and Simulation Module for PCI Express with 1, 2 or 4 Dual Redundant channels (APE1553-1, APE1553-2, APE1553-4) plus 8 programmable discrete Input/Output channels. A unique feature of AIM’s APE1553-x module is the option for the MILScope™ capability. Models APE1553-1-DS/APE1553-2-DS integrate an onboard Analogue to Digital Converter (ADC) which samples, measures and stores the MIL-STD-1553 waveform. Automatic waveform validation is performed by the users Application Software or in conjunction with AIM’s PBA.pro Databus Test and Analysis Software and Test Scripts.
-
product
Specialized Systems and Devices
Is the most comprehensive earthquake monitoring solution for the power generation industry in general and nuclear plants in particular – including seismic-event data recording, analysis and notification via hardware alarms and reports – all in one system, delivering confidence in continuing safe operations after an event.
-
product
Mixed Signal Oscilloscope: 20 GHz, 4 Analog Plus 16 Digital Channels
MSOV204A
20 GHz analog bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.54 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
product
Force Sensors
Our force sensors are indicated for use in modal and structural analysis, process control, and general-purpose dynamic force measurements. See our range of charge modes and IEPE force sensors.
-
product
Green House Gas Analysis
Gas chromatographs help analyze green house gases in air and soil. In addition to nitrous oxide, which is known by its high global warming potential, CO and CH4 are measured by a single analysis.
-
product
Vibrator Test System
Sandwich Box Kit
"Gold standard” for vibrator tests provides more information than radio, wireline similarities or internal analysis. Other forms of vibrator QC use the vibrator controller accelerometers to measure vibrator motion. The Sandwich Box system includes external accelerometers which are used to independently record vibrator motion, thus providing a check of the whole vibrator system including the accelerometers.
-
product
Marine Seismic Systems Analysis Software Suite
Testif-i Marine
Testif-i Marine is a comprehensive software suite designed specifically to process test data from marine acquisition systems to ensure the integrity of your recorded data. The software also contains modules for performing tests on recorded streamer data, such as calculating relative streamer channel sensitivity, comparing gun consistency from near field hydrophone data and comparing the spectra of flip-flop source arrays.
-
product
Thermometer
S0841
Thermometer is designed for record of temperature. Values are stored to a non volatile electronic memory. Data transfer to the personal computer for further analysis is performed via USB, RS232, GSM or Ethernet interface by means of a proper adapter.
-
product
Datalogging Thermometer
R0110E
Temperature datalogger is designed for record of temperature. Values are stored to a non volatile electronic memory. Data transfer to the personal computer for further analysis is performed via USB, RS232, GSM.
-
product
Portable DAQ & Signal Analyzer
ObserVR1000
Vibration Research Corporation
Collect data with the press of a button using the battery powered ObserVR1000 hardware and a mobile interface. Stream to the SD card while running other test modes, or use independently as a field data recorder and analysis package.
-
product
Leeb Hardness Tester
HT6561
Product synopsis1.1 Typical Applications* Die cavity of molds* Inspection of bearing and other mass produced parts on aproduction line* Failure analysis of pressure vessel, steam generator andother equipment* Inspection of installed machinery, permanent parts ofassembled systems and heavy work pieces.* Testing surface of a small hollow space* Material identification in the warehouse of metallic materials* Rapid testing in large range and multi-measuring areas forlarge-scale work piece1.2 Testing...show more -
product
Standard-Res Spectroradiometer
FieldSpec 4 Standard-Res
Analytical Spectral Devices, Inc.
The FieldSpec 4 Standard-Res portable spectroradiometer is the right choice for a wide range of remote sensing applications, including multispectral sensor ground truthing and calibration, agricultural analysis, and snow and ice studies. In addition to being a world class spectroradiometer, the FieldSpec 4 Standard-Res is equally suited to serve as a rugged, portable spectrometer for accurate contact reflectance
-
product
Class 2 Integrating Sound Level Meter
HD2010UC.kit2
The HD2010UC.Kit2 is a Class 2 integrating portable sound level meter performing statistical analyses. The instrument has been designed combining price competitiveness and simplicity of use. Attention has been paid to the possibility of updating the instrument, and the HD2010UC can be integrated, at any time, with other options like “Advanced Data Logger” to extend its application scope.
-
product
Tool
Imagix 4D
Imagix 4D is a tool to understand, document and improve complex, third party or legacy source code in C, C++ and Java. Imagix 4D automates the analysis of control flow and dependencies. It detects problems in data usage and task interactions. With Imagix 4D you increase productivity, improve quality, and reduce risk.
-
product
Audio Analyzer and Digital Audio Bus Module
DP-cPCI-5667
DP-cPCI-5667 is a 6U cPCI Audio Analyzer and Digital Audio Bus Module. This card implements low speed digital audio bus, high speed digital audio bus and audio analyzer features. It is used for general purpose analogue audio analysis and supports low speed digital audio bus and high speed digital audio bus protocols.
-
product
Mixed Signal Oscilloscope: 16 GHz, 4 Analog Plus 16 Digital Channels
MSOV164A
16 GHz analog bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.32 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
product
Soil Mechanics
VERCAM
VERCAM is a program for the analysis and design of retaining, gravity and in concrete walls; which can evaluate the maximum safety factors both under normal and seismic conditions. The programme can automatically calculate the reinforcement bar dimensions and their position as well as verify the corresponding stress in the materials for reinforced concrete barriers.
-
product
Spectroscopy
NIRS XDS Process Analyzer
NIRS XDS Process Analyzer systems can measure a variety of sample types, such as granules, powders, liquids, slurries, or opalescent substances, among others. These analyzers provide fast, nondestructive analysis of pharmaceutical, chemical, and petrochemical products. If required, up to 9 inline measuring channels can be multiplexed with this system.