-
Product
Characterization of Solar Cells
Paios
-
Paios performs a large variety of experiments in no time with one click. Get consistent and precise measurement data, directly compare your results in the measurement software and speed up your research.Increase your research speedCompare your devices directly in the softwareGet highly consistent dataThink about physics - Let Paios handle the rest
-
Product
Solar Cells and Modules Online Measurement System
PV-LIT
-
The fully automatic PV-LIT testing system offers individual and serial testing options for solar cells and complete solar modules. The modular testing system allows easy integration into existing production lines and can be used in automated serial testing for quality assurance.
-
Product
In-Line Light I-V Testing for Solar Cells
FCT-750
-
In-line, light I-V and Suns-Voc measurements in a single flash at 2400 units per hour. Capability to accurately measure high-efficiency conventional or backside-contact solar cells.
-
Product
Testing for Si Solar Cells Using High Performance CCD
EL Imaging Tester
-
EL Testing for Si Solar Cells using High Performance CCD. The determination of luminescence (photo emissions) in solar cells is an important characterization tool. Typical solar cells often have defects which limit the efficiency or lifetime of a cell. Many of these defects are visualized with Luminescence Imaging. By using this technique, the manufacturing process can be optimized to produce better cells. Luminescence Imaging takes advantage of the radiative inter-band recombination of excited charge carriers in solar cells. The emitted photons can be captured with a sensitive CCD camera to obtain an image of the distribution of the radiative recombination in the cell. This distribution is determined by the local excitation level, allowing the detection of electrical losses, thus mapping the diffusion length of minority carriers as the emitted light is low intensity and in the near infra-red range, the CCD camera has a high sensitivity wavelength from 900 to 1100 nm with little thermal noise. This CCD camera provides excellent resolution of 1024 x 1024 pixels with a large 1μm pixel size, multi-megahertz readout speed, and robust USB 2.0 connectivity. The EL CCD Camera is the ultimate high-performance CCD camera for electroluminescence and photoluminescence imaging for Photovoltaic (PV) Cells and Modules. This camera combines low noise electronics and optimal sensitivity in NIR.
-
Product
Solar Cells
-
Using high-efficiency solar panels made of silicon solar cells, the conversion rate as high as 16%, and attenuation, good reliability, long life. Frame using a high-quality anodized aluminum edge, high mechanical strength, ensuring a high level of wind resistance and anti-riot performance, can be adapted to a variety of complex and harsh climatic conditions used.
-
-
Product
Solar Simulator for Multijunction Solar Cells
-
For series connected multijunction cells, at a given spectrum (e.g. AM 1.5 or AM 0 for space solar cells), one of the cells will limit the current in the series connection of cells. All solar simulators deviate from the true AM 1.5 spectrum, and they are only classified in wide spectral bands (100nm width). So even for class A or A+ solar simulators, it can easily happen that the bandgaps of the multijunction cells are such distributed that the 'wrong' cell will limit the current, if a solar simulator with fixed spectrum is used. In the 70s and 80s, when these measurements were first developed, intercomparisons showed deviations of cell efficiency in fixed spectrum solar simulators of more than 40%.
-
Product
Software
Solar Cells/ Photovoltaic Devices
-
Materials Development Corporation
MDC offers a comprehensive array of current-voltage, capacitance-voltage, and resistivity measurements to characterize solar cells and PV devices. CSM/Win systems and software can help to fine tune your process for maximum efficiency. Critical values such as series and shunt resistances, maximum power point (both actual and theoretical), and fill factor are automatically determined.
-
Product
Light I-V Testing for Solar Cells
FCT-650
-
Advanced analysis of solar cells including light I-V and Suns-Voc data.
-
-
Product
Surface Photovoltage
-
The surface photovoltage spectroscopy modules are the perfect all-in-one solution for in-depth studies of light sensitive materials such as organic semiconductors, solar cells or light sensitive dyes.
-
Product
Solar Cell Systems
-
he Solar Cell Scan is a multifunctionalexperimental platform,which is based on the measurement of Quantum Efficiency (QE) . The system employs a turnkey integrated design, which can carry out QE, Reflectivity and Mapping testing functions automatically. There are also modular and customdesigned accessories to adapt to different solar cell samples.
-
Product
SOLAR CELL TESTER
-
The tester is designed for terrestrial solar cell incoming/outcoming inspection with the purpose of checking and optimizing parameters and preventing manufacture defects of solar modules. Solar cells are not heated in process of inspection due to the use of xenon pulse lamp installed in the tester.
-
Product
IV-curve Software
Tracer
-
In Tracer you will find your all-in-one solution for the measurement and elaboration of IV-curve measurements. Tracer is the core application developed by ReRa that will help you to characterize your solar cells and compare the results.Tracer natively supports the control of Keithley 24xx and 26xx sourcemeters.These instruments have proven their strength over time for the measurement of solar cells.
-
Product
Electronic Components
-
We supply a wide range of components and materials to the electronics industry, such as: integrated circuits for personal computers, semiconductor materials for system LSI, optical communication materials for telecommunications, components for display devices seen in smartphones and projectors, and materials used in solar cells and lithium batteries.
-
Product
Interior light simulator
-
It is possible to evaluate characteristics of various solar cells and various sensors with high precision under LED lighting. It is possible to evaluate output characteristics conforming to JEITA standard ET - 9101 *
-
Product
Solar Simulator
-
It is an LED light source for evaluating the performance of organic solar cells in indoor light applications.A neutral white LED light source equivalent to a color temperature of 5000 K, achieving an effective irradiation area of 50 × 50 mm.The illuminance can be changed without changing the height of the light emitting surface with low illuminance (200 lx) and high illuminance (1000 lx).
-
Product
Automated Testing System
PV-LIT
-
Thermographic solutions ensure high quality of solar cells and modules.Usable for all types of solar cells and modules (silicon-based or thin-layered)Testing in laboratory and in-line in the course of the manufacturing processTesting of various solar cells and modules through contact and non-contact measurementCell-specific system configuration and determination of test criteria and kind of defects
-
Product
Reference Cells For PIV-IV Systems
-
NREL calibrated cell used for calibration transfer.The Abet Technologies solar reference cell is a precision instrument for the determination of solar simulator irradiance levels. The sensor is a mono-crystalline silicon solar cell having an area of2x2cm(4cm).The back of the solar cell is attached to the device in such a way that a good heat transfer to the device housing is guaranteed. Below the solar cell a Pt100 RTD temperature sensor is mounted to allow monitoring of device temperature. The device is not shunted allowing the whole IV-curve to be measured. The solar cell is protected by a high quality fused silica window, assuring spectral sensitivity over a 320 -1100 nm range.
-
Product
Integrated I-V Test Systems
-
The OAI Integrated I-V Test System is perfect for R&D as well as production, the OAI Integrated I-V Test System delivers extremely accurate solar cell performance measurement. OAI’s advanced fully Integrated I-V Test System is designed to overcome the limitations of flash testing by providing a highly optimized pulse width and voltage sweep rate to match any type of solar cell’s high capacitance and slow dielectric response speed. As a result, the system produces extremely accurate measurements of solar cell I-V parameters and efficiency while leading to the most accurate test results.
-
Product
Wafer Defect observing instrument
HS-WDI
-
Application■Semiconductor wafer■Solar wafer■Solar Cell■Thin-film Cell
-
Product
Solar Reference Cell
-
The Solar Reference Cells consist of a 20 mm x 20 mm monocrystalline silicon Photovoltaic Cell encased in a 92 mm x 70 mm x 16 mm metal enclosure with a protective quartz window and a temperature sensor. Designed for calibrating the irradiance of solar simulators used for testing solar cells and modules.
-
Product
Solar Simulators
TriSOL CPV
-
Concentrating Photovoltaics (CPV) has the promise of producing solar cells with high cell efficiencies, which result in a reduction in the cost of operating a PV module. However, a CPV system requires the integration of CPV solar cells, modules and CPV optics into one efficient system. OAI’s focus is CPV cell testing methodology. The CPV cells can now be tested using OAI’s advanced standalone CPV Simulators for low dose and high dose configurations. The low dose CPV Solar Simulator provides exposure up to 50 Suns, whereas, the high dose CPV Solar Simulator provides exposure up to 1500 Suns. The low and high dose simulators provide exposure in varying Sun concentrations in various beam sizes from 1.5cm x 1.5cm to 7.5cm x 7.5cm, and may be configured with OAI’s I-V Test Systems.
-
Product
Solar Cell PL/EL/IV 3-in-1 Testing System
VS6841
-
Industrial Vision Technology Pte Ltd.
This luminescence Analyzer integrates a Photoluminescence (PL), Electroluminescence (EL) , and I-V Measurement Technology, has a Device’s PL image, EL image, as well Device’s I-V characteristics in One system. It is being using to quantitatively map Minority-Carrier Lifetime, and to characterize the defect of silicon wafer & solar wafer, and measure the key parameters from solar cell I-V Curve. It is also a useful tool for scientist to develop other methodology & parameters that can be used as a promising technique for online material monitoring and process control.
-
Product
OPV/DSC/Perovskite IV measurement System
-
King Design Industrial Co., Ltd.
The system can measurement the 3rd generation of solar cell IV performance. The system patent with eliminate capacity effect that can ensure the test repeatability coincidence.
-
Product
Solar Simulator for Concentrator Cells
-
Optosolar offers solar simulators with continuous light for small area solar cells (ca. 10mm x 10mm). depending on the cell size, the concentration ratio can exceed 1000 suns. Special designs cover low concentration on large area wafers (156mm x 156mm), as well as line focus applications (e.g. 8mm x 156mm at 8 suns). Flashlight Solar Simulators have the advantage of negligible temperature change to the solar cell. For this reason, they are often used for very high concentration ratios or for multijunction cells in a solar simulator with adjustable spectrum.
-
Product
Display of Energy Yielded by Photovoltaic Plants
VisiKid
-
It enables the direct conversion of sunlight into electrical energy through solar cells - that is why photovoltaics is one of the most popular sources of renewable energy; that is why solar power plants are increasingly being installed on the roofs of nurseries and schools. The aim is both to set an example and teach children about renewable sources of energy.
-
Product
Saluki SEL8 Series Programmable DC Electronic Load (up to 200KW)
-
The new SEL8 series programmable DC electronic load is a new generation product designed by Saluki Technology. Incorporating high-performance chips, the SEL8 series delivers high speed and high accuracy with a resolution of 1mV and 1mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs).SEL8 series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar cell and fuel cell etc. test and measurement applications.* Customization available upon request
-
Product
Solar Simulator
Sirius 150A
-
Solar Simulators are used to simulate “real” solar radiation conditions and are widely used for the photovoltaic device research and QA etc.Beam collimation and spot uniformity are important properties along with spectral matching are key operational requirements. The SS150 and SS1000 are suitable for all types of solar cells and well match their optical requirements.
-
Product
I-V Tracers
-
EKO I-V tracers (MP-160 / MP-11 / MP-180) can be used in three different Power ranges. The research type MP-160 is an all round instrument to be used with single cells and modules or multiple unitswhen connected to the multi channels selectors. The portable MP-11 with remote sensor unit can be used on site to accurately check the performance of Modules and Strings. The high end MP-180 is capable to make high precision I-V measurements of small and large size solar cells and is most suitable for Research and Development applications or production inspection purposes indoors.
