-
Product
CPCI Based 486DX4 Board
MS 1501
-
- CPCI/PXI Bus Interface, 6U form factor- Watchdog Timer- Hot Swap Facility- PCI Bus Rear IO Expansion for External Bus Interface- Debugging Monitor interface through RS232- JTAG interface for 486 for boundary scan test- Power Source through the CPCI connector J1 (±12V, +5V, 3.3V)- 1Mbytes of Dual Port RAM, 256Kbytes of STATIC RAM- 1MBytes of FLASH PROM- RS232, RS422 Serial Interface- Intel 486DX4 operating at 100MHz frequency at the core- Driver interface for Windows2000/XP/VISTA and LINUX/RT LINUX OS
-
Product
Ionic Contamination Test System
Omegameter SMD 650
-
The SCS Omegameter SMD 650, the long-time industry standard for ionic testing utilizing “static test” methodology, is designed to perform cleanliness testing on printed circuits and assemblies. Identifies the presence of ionic contamination on bare and assembled printed circuit boards and other electronic components. Provides an accurate and repeatable method for determining cleanliness on site. Provides immediate process control results, eliminating the need for outside laboratory testing.
-
Product
Torque Sensors
-
A device for measuring and recording the torque on a rotating system, such as an engine, crankshaft, gearbox, transmission, rotor, a bicycle crank or cap torque tester. Static torque is relatively easy to measure.
-
Product
In-line Plastic Mixers
-
Ideal for one-use fluid dispensing, Nordson EFD’s disposable static mixers eliminate the need to worry about premature curing of materials.
-
Product
High Line Pressure Transducer
P365
-
The P365D transducer is designed to make low differential pressure measurements at high static line pressures. Operating from unregulated 9 to 55Vdc, the P365D is available with 4-20mA, 5Vdc or isolated 5Vdc output over full scale pressure ranges from 8 to 10,000 psid. The output shift due to static pressure will not exceed 3% of full scale, up to a line pressure of 10,000 psig.
-
Product
Measuring Devices for Magnetically Hard Materials
MAG-ST100
-
The computerized measuring system is designed for measure the static magnetic properties of the hard magnetic materials e.g. Alnico, ferrite, magnets based on cobalt alloy with rare-earth elements or Nd-Fe-B alloy. The system provides the opportunity of a tabular and graphic presentation of the obtained data, which can be presented by means of monitor, printer or plotter. MAG-ST100 system fulfill the requirements of IEC404-5 Standard.
-
Product
Static Electric Motor Analyzers
-
Baker Instruments’ static motor test equipment is the industry-leading suite of products for detecting weaknesses and faults in the insulation systems of electric motors, generators and coils. Employing both low-voltage and high-voltage tests – such as Baker’s signature surge test - these essential troubleshooting and predictive maintenance tools allow maintenance professionals to assess any need to maintain or replace specific motors and generators that support their business. Equally at home in the motor repair shop or on a plant floor, these testers ensure that the electrical condition of your rotating machinery is understood.
-
Product
Electrostatic Fieldmeter
Model 775
-
The pocket-sized Simco-Ion Model 775 Handheld Electrostatic Fieldmeter is designed to locate and measure static charge potentials on product, people, equipment and packaging. The Model 775 Fieldmeter uses a non-contacting, chopper stabilized field sensor and a ranging light mechanism to ensure correct measurements of electrostatic fields in all areas—even those using air ionization.
-
Product
Compact Tension Grips
-
These compact tension grips are for plane-strain fracture toughness tests of metallic materials. Fracture toughness testing involves applying static loads to a notched sample to investigate brittle crack propagation and fracture conditions.
-
Product
Instron Materials Testing Software
-
Instron offers a comprehensive suite of materials testing software solutions designed to support a wide range of mechanical testing applications, from static tensile and compression to fatigue, impact, and melt flow. Built for precision and efficiency, these software packages provide powerful tools for test control, data analysis, and reporting, with support for industry standards such as ASTM, ISO, and EN. Whether for basic quality control or advanced research, Instron’s software solutions deliver flexible, user-friendly interfaces and robust data integrity features to meet the diverse needs of modern testing laboratories.
-
Product
Rotor Balancer
-
Static and Dynamic Balancing of Rotating MachinesBalanced rotors are essential for the smooth operation of rotating machinery. Unbalance will create high vibrations, reducing machine life and causing material defects. Our single and dual-plane balancing tool is a great tool to eliminate unbalance on-site reducing long down times.
-
Product
Secondary Ion Mass Spectrometry (SIMS Analysis)
-
Rocky Mountain Laboratories, Inc.
Secondary ion mass spectroscopy is operated either in the dynamic mode (DSIMS) or the static mode (SSIMS). DSIMS is useful for profiling impurity and trace elements through films and interfaces. SSIMS is useful for characterizing polymeric materials and only measures the outermost molecular layer of a specimen.
-
Product
ResMap or DualMap Auto Load Table Top
-
Creative Design Engineering, Inc.
*Type: Table Top*Wafer load: open cassette*Wafer size: 4" to 8"*Mini Environment: N/A *Probe Changer: N/A *Aligner: N/A*Size: 12" x 28" x 10"*Range: 1m/ to 10M/*Accuracy: 0.5%*Repeatability: 0.02% *Static Repeatability: 0.1% dynamic
-
Product
Human Potential Measuring Instrument
KSD-4000 / KSD-4100
-
Electronic devices and metal tools carried by workers have individual capacitance to ground and are charged at human potential. When the charged electronic device touches the ground or a metal tool touches the electronic device, a transient current with a high peak current flows at high speed, Causing A Failure. By Using The Human Body Potential Measuring Device, The Potential Of The Human Body Can Be Measured Accurately, And It Can Be Immediately Determined Whether Or Not The Electronic Device Is Damaged By The Potential. You Can Also Find Out How Much Static. .. .electronic meters such as conductive floors, electrostatic mats, electrostatic shoes, and wrist straps reduce the human potential.
-
Product
NI-9403, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module
780179-01
Digital Module
5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The NI‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9403 for applications such as custom, high-speed counter/timers; digital communication protocols; and pulse generation. In a CompactDAQ chassis, you can use the NI‑9403 only as a static (software-timed) digital I/O module. You cannot use these modules to route timing or triggering signals.
-
Product
Portable Touchplate Wrist Strap Tester
-
Testing your ESD Wrist Strap system before handling electrostatic sensitive is extremely important. ESD events can go unnoticed by feel and sight. While a static discharge into a door knob (we’ve all done it!) can be thousands of volts, an ESD event can be as little as 10V, and you will not feel this. This is a no-frills, “go-no-go” type tester, but portable. Sure you could put this at your entry point, but where it really shines is in special remote applications. Keep one in your tool box, bag or Field Service Kit.
-
Product
Motor Drive Analyzer, 1 GHz, 8 Ch, 12 bits, 10 GS/s, 50 Mpts/Ch
MDA 8108HD
Analyzer
Static power analysis - like a dedicated power analyzer.Dynamic power analysis – capture more information.Complete test coverage – control system, power section, motor.Comprehensive mechanical interface.Harmonics calculation option.Vector display option (THREEPHASEVECTOR).Waveform Transformations option (THREEPHASEdq0).16 Channels with OscilloSYNC™.
-
Product
Digital Megohmmeter
800
-
The ACL 800 Digital Megohmmeter is a dependable and easy-to-use audit kit that is designed to test static dissipative surfaces for electrical resistivity and resistance according to industry standards such as ANSI/ESD test methods S4.1, S7.1, and ASTM D257. Tests are easy to perform with or without the 5lb probes. Use optional concentric ring probe for conformance to STM11.11.
-
Product
PXI Digital IO
-
The Keysight M9187A Digital I/O provide static digital input and output channels which can be used in applications that require the monitoring of digital states and the controlling of external devices. These are typically used in aerospace/defense, automotive, and electronic test applications. The module offers configuration flexibility with programmable input thresholds and flexible output drive capability.
-
Product
High Sensitivity Anemometer for Very Low Wind Speeds
HD53LS… Series
-
2-axis ultrasonic static anemometer - high sensitivity to dectect very low speeds. Measurement of wind direction, wind speed and wind gust.
-
Product
(100kN) Fatigue Testing Systems
8801
-
The 8801 servohydraulic testing system meets the challenging demands of a varied range of both dynamic and static testing requirements. The 8801 provides complete testing solutions to satisfy the needs of advanced materials and component testing, and is ideally suited for high- and low-cycle fatigue testing, thermomechanical fatigue testing, and fracture mechanics. The higher capacity of up to 100 kN, a larger working space, a high stiffness, and the precision of alignment all make the 8801 an exceptionally versatile and reliable testing system.
-
Product
8GE+4G SFP L3 Managed Ethernet Switch, -40~75℃
EKI-9612G-4FI
-
DIN-Rail L3 switch 8 Gigabit ports + 4 SFP ports, L3 function :Static route , NAT, SFP socket for Easy and Flexible Fiber Expansion. Redundancy: X-Ring Pro (ultra high-speed recovery time < 20 ms), RSTP/STP (802.1w/1D) Security: 802.1x, Management: SNMP v1/v2c/v3, WEB, Telnet, Standard MIB, Private MIB.
-
Product
WINSTAT
-
This air ionizer is designed to remove static electricity in a wide range of industries, including ESD (electrostatic discharge) problems in the electronics industry and static countermeasures for plastic films. Air ionized by corona discharge in the discharge electrode is transported by a fan, neutralizing static electricity on charged objects located at a distance and preventing static electricity problems. The fan allows for static elimination over a wide area and long distances, and a wide range of models are available, including high-frequency, AC, and DC types, making it suitable for a wide range of applications, including equipment, desktop, and line use.
-
Product
Advanced Hydraulic Wedge Action Grips
2742 and 2743 Series
-
The Instron advanced hydraulic wedge action grips deliver controlled, constant gripping force using an external hydraulic supply across static and dynamic testing. They support capacities up to 600 kN (static) and 500 kN (dynamic), with interchangeable jaw faces for round or flat specimens. The design ensures jaw face positions remain fixed during gripping (eliminating preload), compensates for changes in specimen thickness, and is ideally suited for use with metals, composites, and plastics.
-
Product
Ultra Compact Ionizers
ER-V Series
-
Panasonic Industrial Devices Sales Company of America
The ER-V Ultra-Compact Ionizer offers a new style in charge removal. It uses high frequency AC in an ultra-compact Ionizer for superior static elimination.
-
Product
ISA Isolated Digital I/O Boards
ISO-LDH/LDL
-
The ISO-LD series is a bus-type isolated loadcell input board. The isolation inputs can operate with up to 500Vrms of common-mode voltage. The ISO-LD series features a 12-bit analog-to-digital converter, on board 1 K bytes FIFO buffer , one loadcell signal input channel, one analog input channel, 8-channel 12-24V isolated digital inputs, 7-channel isolated open-collector digital outputs, one programmable 8-bit LED indicator to indicate the magnitude of strain gauge input signal. The ISO-LD series board is suitable for static force measurement and dynamic force analysis. Because there are on board excitation voltage, high gain amplifier, you don*t have to buy any excitation voltage and signal conditioning module. In other words, it save your money and space.
-
Product
Lightening Protection
Towers & Antennas
-
LBA offers a wide variety of lightning air terminals in the form of lightning dissipaters. Sometimes called a static dissipater, or static dissipation array, this relatively new and advanced air terminal replaces conventional lightning rods in most applications. It functions as a streamer retarding air terminal.
-
Product
64-Channel VME Relay Module
V210
-
The V210 is a single-wide, 6U VME module that includes 64 SPDT relays and drivers. User-settable DIP switches set the A16/A24 VME address mode, VME address, and select whether the relays are statically operated or operate in latching mode, where relay states are sustained when VME crate power is off.
-
Product
500 N Screw Flat Grips
-
500 N (110 lbf) screw flat grips are for use with low-capacity AGS-X series and EZ-X series load cells and come with flat grip faces. Similar to standard screw flat grips, these grips are versatile and are used for static tensile testing a wide range of materials, including rubbers, plastics, textiles, cloth, and paper, in film form.
-
Product
Switch Analyser
SA10A
-
It has a built-in micro Ohm meter/Ductor for measuring of static and dynamic resistance of the breaker poles. It only weighs 11,6 kg. The versatility and precision that this unit offers is, without question unchallenged, and it will indeed be your best partner when testing circuit breakers. Tests in areas with high induction at known problematic substations has proven the SA10A to be the only circuit breaker timer that could withstand these extreme conditions. It's rugged, it's small and highly appreciated by our customers.
