-
product
Fastest Flying Probe Test System for Semiconductor Substrate Interconnect Test
GATS-3200
* Test individual packages or * Test Multi-image panels with Step&Repeat Function * single flying probe top using very high speed voice coil motor (VCM) technology * 50 - 100 tests per second ... high throughput * Dual Flying Probe Top for testing bump-to-bump nets * flying probe head allows testing of all nets including each power and ground point * 4-wire test capability
-
product
Scienlab Battery Test System — Cell Level
SL1002A
Test System with up to 36 Channels.The Keysight SL1002A provides sink and source with 0 to 6 V, 100 to 600 A, 0.6 to 3.6 kW and 36 channels for battery cells.
-
product
Resistivity Cell For N1413 (50 Mm Electrodes)
N1424A
The N1424A is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424A to the B2985B/87B.
-
product
Cell Testing
PEC offers a wide range of cell testers, starting from the 5A desktop test system (ACT0505), to our range of 50A cell testers for more standardized cycling (CT0550) and our advanced cell testers with capabilities up to 4000A (ACT0550). All systems support parallel switching for achieving higher currents.
-
product
Thru Hole Donut Load Cell
Futek Advanced Sensor Technology, Inc.
The Thru Hole Donut Load Cell Series offers 5 models built for Off-Center Loading, Press, or Inline compression applications. These models have a very robust construction available in 17-4 Stainless Steel, with an I.D. range of 1/8" to 1 1/4".
-
product
PXI Mixed Configuration Relay Module - 7 Cells Populated
40-138-AA-BB-CC-DD (7 CELL)
The 40-138 2A Relay Module with 7 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
product
Battery Cell Simulation / Emulation
BMS
Efficiency, reliability and safety of modern lithium ion batteries for electric vehicle drives strongly depend on the battery management system (BMS) as their electronic control unit.
-
product
Test Cells (
LaplaCell
LaplaCells provide a facility for the rapid and efficient testing of the EMC compliance of products. These cells offer a calibrated and screened environment in which radiated emissions can be measured and immunity to RF radiation can be tested. They \re calibrated according to the methodology of IEC61000-4-20, thus affording compliant testing to IEC61000-4-3 and pre-compliance testing for radiated emission testing.
-
product
Coating Thickness Meter for Ferrous Substrates
CM8821
- Operating principle: magnetic induction (F)- Measuring range:0-1000um - Resolution; 0.1/1- Accuracy: 鍗?-3%n or 鍗?.5um- Min. measuring area: 6mm- Min. sample thickness: 0.3mm- Battery indicator: low battery indicator- Metric/ imperial: convertible- Power supply: 4x1.5V AA (UM-3) battery- Auto power off- Operating conditions:0-+45閳?/span>(32閳?/span>-104閳?/span>),閳?0%RH- Dimensions: 160x68x32mm- weight: 250g(not including battery)- Optional accessories: other range 0-200um to 15000um
-
product
PEM Fuel Cell
48 Volt 5kW
It is the aim of CellCare Technologies to continually introduce new technology that can provide significant benefits over existing solutions in specific applications. Fuel cellThe latest introduction to the product portfolio is a 5kW PEM (Proton Exchange Membrane) based hydrogen fuel cell, designed to replace 48V standby batteries within remote telecoms sites, satellite base stations, ISP base stations, uplink facilities and weather data collection sites. This technology provides instant power with no hazardous waste, zero emissions, extended autonomy and a guaranteed lifetime with minimal maintenance.
-
-
product
Cell, Module & Pack Testing
Cell, Module and pack battery formats are crucial for electrification in transportation and energy. Arbin Instruments' test equipment is designed for performance-based tests, to meet the needs of these complex formats.
-
product
Direct Burial Half Cell Reference Electrode
DB-A
Model DB-A Copper-Copper/Sulfate Reference Electrode designed for direct burial for long term monitoring of buried or earth contacting structures.
-
product
Parallel Plate Dielectric Test Cell
LT-4203A
The LT-4203A Parallel Plate Dielectric Test Cell is designed for measuring the AC loss characteristics and permittivity of solid laminates and panels per ASTM Standard D150‑98, and implements the guarded electrode (three terminal) measurement preferred as the referee method.
-
product
Industrial Weighing - Wireless Load Cells
A wireless industrial weighing scale system can be advantageous, for instance when running conduit for cable is impossible, or if the cable could be damaged easily. In some cases the wireless interface is more economical than long runs of cable. These systems can be battery operated or hard wired to a power source if available. View our wireless load cell options below.
-
product
Calibrated Solar Reference Cell
To insure repeatable testing on any solar simulator, OAI offers 2cm x 2cm calibrated reference cells. Standard reference cell calibration cycles can be set up by OAI''s calibration laboratory to insure that your reference cell maintains certification.
-
product
Low Capacity Single Point Bending Beam Load Cells
LSP SERIES
The LSP Series is a low capacity, low cost, high accurate single point bending beam load cell. It is ideal for OEM applications such as electronic scales and weighing machines. The single point design is highly resistant to eccentric loading allowing direct mounting to the scale base and weighing platform. The LSP Series features a moisture proof sealant.
-
product
Dynatrol® Red Goose V2 Cell For Pipeline Products
The Red Goose v2 Pipeline Products Inline Sampling System can be used on gasoline, diesel fuel, jet fuel and other refined petroleum products. It was designed so no removal is needed during pipeline maintenance and utilizes a retractable scoop used for pigging or scraping operations.
-
product
Cell Production Measuring Technology
More than 2000 halm systems are already installed in the field, all of which fully comply with the IEC60904-9 standard. In the latest standard (Edition 3.0), our current systems are even rated A+A+A+.
-
product
Through Hole Load Washer Load Cell Compression Only
LWO SERIES
The LW0 Series are washer shaped, strain gage based load cells that have been most commonly used in fastener testing and thru hole load applications. Our stocked ranges from 2,400 through 300,000 lb compression are made from 17-4ph heat treated stainless steel and are matched to bolt diameters and their specific load characteristics. Modifications of diameters, thicknesses, or load range to a specific diameter for OEM applications are welcomed. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
product
Small Cells
5G small cells enable additional capacity and coverage to networks when and where needed – both indoors and outdoors. Our 5G protocol software for small cells supports both sub-6 GHz and mmWave bands and leverages the Small Cell Forum’s FAPI and nFAPI open interfaces to work seamlessly on our partners’ SoC-based small cell platforms.
-
product
Low Profile Compression Only Load Column Load Cell with Mounting
CLC SERIES
Our CLC Series is our high capacity compression only load cell, featuring low profile compact size for a wide range of portable and dedicated applications. The loading diameter (D1) is slightly convex for accurate load distribution. Low deflection through design results in ultra fast frequency response. All ranges are made from 17-4ph heat treated stainless steel and incorporate a stainless steel molded connector system designed to resist washdown and splash. The mating connector, sold separately, is available in three different cable lengths.
-
product
High Precision Compression Type Load Cell
HR II
A high-precision compression-type load cell is a sensor that accurately measures compressive (pushing) forces, designed for applications requiring very tight accuracy and reliability. It works by converting a downward force into an electrical signal, often using strain gauges to measure deformation, and is used in demanding fields like calibration, manufacturing, and medical equipment.
-
product
Ultra Precision Mini Load Cell Universal/ Tension or Compression
MDB SERIES
The MDB Series Load Cells was designed to help fill the growing need for a greater selection of high accuracy load cells for use in space limited applications. The anodized aluminum MDB's are compliant in tension and compression, therefore, a good choice for in line through zero applications, as well as single direction tension or compression. Applications may include load feedback for process control, low capacity tensile testing machines, robotics, or designed into your product. Give us a call, we would be pleased to discuss your application requirements.
-
-
product
Cell Isolation & Analysis
Life's complexity originates in cells, spanning cellular structure, genetic diversity, gene expression, and complex tissue formation. Serving as the fundamental unit, cells form the foundation of all biology. Characterization of cells, their processes and interactions can provide insights into areas like medicine, symbiosis, and biological diversity. Bio-Rad supports these inquiries, offering innovative technologies for your cell biology research.
-
-
product
Load Cell Tester
LCT-Ultimate
Industrial Measurement Systems Ltd.
This most advanced Load Cell Tester model LCT-Ultimate is a stand-alone hand-held device that was especially designed for full trouble shooting of strain-gage based load cells. The LCT-Ultimate can check all common types of standard load cells that are available on the market:
-
product
PXI Mixed Configuration Relay Module - 12 Cells Populated
40-138-AA-BB-CC-DD (12 CELL)
The 40-138 2A Relay Module with 12 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
product
Large Substrate Mask Aligner
Model 6020
The Model 6020 is a large substrate Production Mask Aligner or Auto-flood Exposure System for RDL First Level Advanced Packaging (PLP) and markets requiring exposure of large glass panels. It is engineered with OAI’s precision, reliability, and quality that is found in all of OAI’s products. The features include wedge effect leveling, superb process repeatability, ≤ 2.0µm printing resolution, and remote diagnostics. Using robotic handling, the system can stand alone or be fully integrated with photo resist processing.
