-
product
Pod with Four Test Access Ports for 5v or 3.3V TTL Thresholds
JT 2137
The JT 2137 pod remains a popular choice for DataBlaster controller installations that require a compact signal conditioning pod embedded within a test fixture. The JT 2137 features four test access ports which together may be set for 5v or 3.3V TTL thresholds, although additional plug-in adapters are available that allow alternative thresholds to be set on a TAP by TAP basis (contact your local sales office for details). The 20-way 0.1″ IDC TAP headers comply with the standard JTAG Technologies 20-way pin-out and provide the additional flash programming controls Read/Busy and AutoWrite.
-
product
PXIe-8523, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module
787311-01
PXIe, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8523 is a 100/1000BASE-T1 unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module for developing applications with the NI‑XNET driver. With this hardware, you can develop applications … that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8523 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, so it can synchronize with an external network as well as the rest of a PXI system. The PXIe-8523 also provides LEDs on the front panel to help you monitor the network link and activity.
-
product
High Voltage System
HV-2
International Electro-Magnetics, Inc.
*Tests Power Transformers for Continuity, Ratio and Phase. Applied and Induced Potential and No-load Losses.*14 Conductor Switching Matrix will test 7 individual windings, 13 taps of one common winding or some combination thereof. (10 Amp current limit)*The System Control is Windows/Visual Basic based. Menu screens allow full selection of test parameters and sequence. Low voltage tests can be performed first, allowing defective parts to be rejected without proceeding to time consuming induced Potential dwell routines. Test data labeling and data acquisition software can be easily added to the system.
-
product
Automatic Three Phase Transformer Ratio Meter
ATRM PLUS
*Fully Automatic measurement.*Wide selection of Excitation Voltages of 10V, 40V, 100V, 230V & 250V from front panel.*4V Excitation voltage provided for CT measurements*Ratio range of up to 5000; direct display of measured ratio.*No conversions required.*Automatic Jumper selecting as per the vector*Diagram of Transformer.*Automatic testing of all 3 phases in 3 phase transformers*Without manual intervention.*Displays % deviation from a nominal ratio.*External storage facility using pen drive.*Internal storage up to 10000 readings.*Touch screen 7” Color TFT display with backlighting with*Resolution of 800 X 480.*Tap changer facility.*Computer interface using RS-232 or USB.*Windows Interface software provided for data transfer.*USB printer interface.*Four terminal measurements to reduce errors due to*Winding and lead resistance.*Auto print and storage facility.Fast measurements.
-
product
Tap Adapter
Techimp Voltage Tap Adapter is gender changer which allows the user to connect to the test tap (sometimes called power factor tap) of high voltage transformer bushings.While keeping the test tap well below the safety voltage level required by the manufacturer, the Tap Adapter lets the user to drain high frequency PD signals for diagnostic assessment of insulating materials.A synchronization signal can be derived as well.It is suitable for both single shot as well as continuous PD monitoring.Although it must be customized on the basis of the shape and dimension of the test tap (to be provided by the Customer), many models are readily available for the most established transformer bushings. A list of the presently available models is reported below.Several thousands of hours of operation are a guarantee of reliability and accurate design.
-
product
Customized Cards & Modules
Tap into the resources of both a world-class electronics manufacturer in Molex, and a proven Engineering team that has been designing complex FPGA products since 1993. It’s a unique combination. Our experienced staff, IP, processes and facilities are the ingredients of a world-class design and manufacturing partner that our customers value for their most important projects.
-
product
Transformer Ratio Meters
The TRT is based on state-of-the-art technology and uses the most advanced technique available today. The test equipment can be used to test both single-phase and three-phase transformers, both with and without tap changer in accordance with the requirements of IEC 60076-1.
-
product
General Purpose Low-side MOSFET Drivers
Renesas' family of low-side FET drivers are very high-speed matched dual-drivers capable of delivering peak currents of 2.0 amps into highly capacitive loads and excellent at driving large capacitive loads with minimal delay and switching times. The high-speed performance is achieved by means of a proprietary "Turbo-Driver" circuit that speeds up input stages by tapping the wider voltage swing at the output. Improved speed and drive capability are enhanced by matched rise and fall delay times. These matched delays maintain the integrity of input-to-output pulse-widths to reduce timing errors and clock skew problems. This improved performance is accompanied by a 10 fold reduction in supply currents over bipolar drivers, yet without the delay time problems commonly associated with CMOS devices. Dynamic switching losses are minimized with non-overlapped drive techniques.
-
product
DIN Backplane
VECTOR Electronics and Technology, Inc.
Universal (uncommitted) multilayer backplanes are designed for unique one of a kind applications requiring custom pin-out wiring from connector to connector. Each individual connector pin must be "assigned" by connecting to adjacent power or ground pins with wire or jumpers. Power or Ground input through a labeled series of power taps (screw terminals) along to top and bottom of the board.
-
product
PM Coupler
Zhongke Rayzer Optical Technology Co.,Ltd
Polarization Maintaining Fused Tap Coupler product, is used to divide input polarization maintaining fiber into two outputs according to the established spectral ratio. It is widely used in the fields of fiber laser, fiber amplifier, fiber communication and fiber sensing, with compact configuration, low insertion loss, low polarization related loss and high stability.
-
product
CATV
Sharp Vision, always first in innovation, offers you complete range of DC FTTH products to enable you to achieve better picture & sound quality at low cost & high reliability. The full product range of DC – FTTH products includes Fiber Transmitter cum Fiber Amplifiers(FTFA), DC & Battery Transmitters, Fiber Amplifiers, Nodes, Hybrid Amplifiers, DC Tap off, Splitters and PSP.
-
product
NI-1483, Full-Configuration Camera Link Adapter Module for FlexRIO
781341-01
The NI‑1483 makes FPGA image processing possible for FlexRIO systems. It supports 80‑bit, 10‑tap base‑, medium‑, and full‑configuration image acquisition from Camera Link 1.2 standard cameras. You can pair the NI‑1483 with a PXI FPGA Module for FlexRIO to perform custom image analysis. FPGA processing is ideally suited for applications that require bit-level processing and very low system latency. Implemented in hardware, FPGA processing does not require CPU intervention. You can process images on the FPGA independently or with a CPU for more advanced preprocessing architectures.
-
product
T8730 AIR FLOW TESTER UNIVERSAL
T8730 was designed for the precise task of measuring flows on parts such as filters (medicinal, diesel or petrol), tubes, nozzles, openings, valves, etc…Other than the classic flow measurement, the tool also has other ways of making it as versatile as possible in its category: ascent and descent ramps, opening tests and burst testing.Another separate function is the "continuous measurement", i.e. a test with infinite times allowing adjustment of the taps and part repairs in real time.The tool also avails of an intelligent pressure adjustment, which uses the automatic pressure regulator to continuously adjust the test pressure based on the variation in load loss, to ensure the reading is as stable and repetitive as possible.
-
product
BERTScope Digital Pre-emphasis
DPP Series
The Digital Pre-emphasis Processor DPP Series takes in single-ended inputs of data and clock and conditions the signal by adding precision amounts of pre-emphasis for use with Bit Error Rate Testers. Nine Tap Linear Equalization supporting speeds up to 32Gb/s is supported with the LE320 Series remote head, offering compact two channel precision equalization.
-
product
eDAK For MAC Panel
JT 2147/eDAC for MAC Panel
The JT 2147/eDAK is a new variant of the JTAG Technologies QuadPOD signal conditioning interface specifically designed for use within a MAC Panel ‘Scout’ mass interconnect interface. The unit integrates both the JT 2148 transceiver circuitry plus four independent, programmable TAP modules (two of type JT 2149 and two of type JT2149/MPV) on a single board that matches the MAC Panel Direct Access Kit (DAK) form factor. Overall this configuration offers four Test Access Ports, 64 Digital IO Scan channels and reconfigurable (SCIL) capabilities
-
product
Force Sensors
General purpose force sensors are offered in either stud or axial mounted configurations. They are internally pre-loaded and can be used for dynamic compression, tension, and impact force measurements. Tapped mounting holes on both ends of the radial connector style support link, platform, integrated link, and free-standing installations. The axial mounted type offers protection of the electrical connector and sensor cable from potential damage during drop testing and in free-standing installations. Supplied impact caps facilitate impact and drop force measurements.
-
product
Automated Measurement Expert (AMX), VNA Plugin
S94702A
The Keysight automated measurement expert (AMX) is a smart software solution for automated multiport S-parameter measurements with the PXIe vector network analyzers M937xA/M9485A or the benchtop E5080A ENA network analyzer. The S94702A AMX VNA plugin adds S-parameter measurement capabilities to the Keysight test automation platform (TAP). The combination of the TAP and the VNA plugin forms the AMX backend software, which makes the VNA setups and executes the test sequences in the PXIe controller according to the optimized test sequence files generated by the AMX test plan builder. Other instrument plugins allow you to control the DUT mode, expand the number of test ports with the PXI switches or multiport test set, and use external instruments such as a DC power supply and a digital multimeter. The AMX backend software also provides step-by-step calibration wizard for full multiport calibration using the 4-port ECal module.
-
-
product
Voltage Dividers
Measurements International Ltd.
A series of resistors or capacitors which can be tapped at any intermediate point to produce a specific fraction of the voltage applied between its ends.
-
product
Protocol Analysis
GL's protocol analyzer provides monitoring a communication link in accordance with industry protocol standards by non-intrusively tapping the network under test. The simple framework of the protocol analysis software helps you easily identify the improper sequence of protocol messages, and filter out frames causing the protocol violation.
-
product
Ultrasonic Flowmeters
Clamp-on type sensor easily mountable on existing pipe Suited for a wide range of liquids, for example, deionized water, cooling water, chemical solution, drinking water, sea water, oil, tap water, hot water, industrial water, corrosive liquids. Ultrasonic flowmeter for air is also available
-
product
Pipeline & Cable Locator
STC-PCL 1101
Shanghai Stone Communication tech Co., Ltd
STC-PCL1101 Pipeline & Cable Locator consists of a Transmitter and a Receiver, used in the underground utilities route locating, the depth measuring and long distance tracing. We adopted multicoil electromagnetism technology on this Pipeline & Cable Locator, enhanced the pipeline localization to decide the depth precision and the goal pipeline recognition capability, also could accurately carry on tracing and the localization in the pipeline crowded complex region to the goal pipeline. Thus it is widely used in the telecommunication, electric, tap water, natural gas, physical prospecting, town planning and so on.. STC-PCL1101 has many optional accessories, thus increased their use, and expanded their application scope.
-
product
Turns Ratio Testing
The transformer turns ratio test, or TTR test, confirms that the transformer has the correct ratio of primary turns to secondary turns. Using this test correctly can help to identify tap changer performance, shorted turns, open windings, incorrect winding connections and other faults inside transformers. Megger’s range of TTR testers are robust to withstand the harsh conditions that some transformer testing in. The range includes varying features to simplify and speed up testing as well as 3 phase TTR testers and PT and CT TTR testers.
-
product
Capacitance And Tan Delta Test
Bushing Tap Adapter Kit
Bushing Tap Adapter Kit is designed to perform Capacitance and Tan Delta tests on power transformer bushings The kit can b e used with the following ISA Test Set STS 5000 TD 5000 STS 4000 TD 5000 TDX 5000.
-
product
Turns Ratio Testers
TRT Standard Series
When it comes to choosing a transformer turns ratio tester, TRT Standard series offers some of the most advanced instruments with LCD display out in the market. Each model measures transformer excitation current and phase shift performs automatic vector group detection and magnetic balance on three-phase transformers and three-phase autotransformers. Furthermore, they have a built-in true three-phase power source. Because of that, TRT Standard instruments can test transformers with special configurations, such as phase-shifting, rectifier, arc-furnace, traction transformers, etc.The instruments can output test voltages from 1 V AC to 250 V AC, depending on the chosen model. High test voltage of 250 V AC provides more accurate turns ratio testing compared to other turns ratio testers on the market and extremely low test voltage of 1 V AC enables turns ratio verification of current transformers.TRT Standard series consists of:TRT03 Models (TRT03A, TRT03B, TRT03C) – single-phase voltage up to 100 VTRT3x Models (TRT30A, TRT30B, TRT30C, TRT33A, TRT33B, TRT33C) – single and true three-phase voltage up to 100 VTRT63 Models (TRT63A, TRT63B, TRT63C) – single and true three-phase voltage up to 250 VMore about models differences can be found under the downloads tab, in brochures and comparison sheets.A user can create test templates using the DV Win software and store them in the PC’s memory for later use when in the field.TRT Standard series models have a built-in tap changer control unit. Consequently, it enables remote control of an on-load tap changer (OLTC) directly from the tester. In order to make the most out of this feature, the DV-Win software can be programmed to do everything automatically – running turns ratio tests, changing OLTC tap positions and saving results. This option, especially in combination with test templates, significantly facilitates and shortens the turns ratio testing time.
-
product
Cutting Tool Breakage Detection Switch
TLPS/MTLPS/UTLPS
An air sensor that detects damage and damage to drills and taps in metal processing lines even when rotating.For the detection nozzle, a dedicated nozzle unit that matches the cutting tool is available.We also respond to use in adverse environments, which is one of the features of the air sensor.
-
product
Reduced Voltage Motor Starting Panels by Reactors
A method to limit motor starting current is a series reactor. Iron core or air core reactors can be used for starting purposes. If an air core is used for the series reactor then a very efficient and reliable soft starter can be designed which is more suitable for high MW ratings of synchronous/induction motors at MV levels. The reactors are designed with taps.
-
product
Camera Link Adapter Module For FlexRIO
The Camera Link Adapter Module for FlexRIO supports 80‐bit, 10‐tap base‐, medium‐, and full‐configuration image acquisition from Camera Link 1.2 standard cameras. You can pair the Camera Link Adapter Module for FlexRIO with a PXI FPGA Module for FlexRIO for applications that require bit‐level processing and very low system latency. With the Camera Link Adapter Module for FlexRIO, you can use the FPGA to process images from the camera in-line before sending the images to the CPU, enabling more advanced preprocessing architectures.
-
product
Maple Syrup Refractometer
PA202X-306-307
The eMaple Digital Maple Syrup Refractometer can be used at the tree tap or tank to measure maple sap, for pre-process monitoring of reverse osmosis, in the sugar shack to determine when to draw maple syrup from the boiler, or during maple syrup bottling and testing. The eMaple Refractometer features two scales and measures from 0 to 85 Brix.
-
product
TAP Signal Isolation Module
JT 2139
The JT 2139 is a TAP signal isolation module designed for use in combinational test systems that utilise multiple instrument interfaces. To avoid parasitic capacitance effects and/or unwanted ground loops the JT 2139 can be used to completely galvanically isolate any JTAG Technologies boundary-scan controller from the remainder of the instrumentation system. JT 2139 isolators are a standard component of the JTAG Technologies ‘Symphony’ systems that integrate boundary-scan with In-Circuits Testers etc..
