-
product
2X16 USB Solid State Switch Matrix, 300 KHz To 6.5 GHz
P9164A
P9164A 2X16 USB solid state switch matrix, 300 KHz to 6.5 GHz is a full cross-bar switch matrix that provides a switch based multiport VNA solution in the form of compact USB controlled involving a larger scale of multi-DUT or multiport measurements such as 5G massive MIMO antenna measurement and others
-
product
40 Gigabit Ethernet AdvancedTCA® Fabric Interface Switch Blade
aTCA-3710
The aTCA-3710 is a high performance, high bandwidth, 40G Fabric switch blade for AdvancedTCA® platforms. This product is ideal for bandwidth intensive telecom applications such as wireless access controller, DPI/security network, IPTV, IP multimedia subsystem, RNC/BSC, broadband access/bearer network, data center, and LTE/4G network applications. The aTCA-3710 provides 40GbE hub-to-node connectivity and integrated switch silicon that supports load balancing, priority queues, packet classification, and flow control to enable strict bandwidth management for implemented applications.
-
product
PXI SPDT Switch: 64-ch, 100 Vrms / 1A, Reed Relays
M9131A
The M9131A is a high-density, general purpose switch with 64 independent, single-pole, double-throw (Form C) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights, or actuate external power relays and solenoids. The high-speed, long-life reed relays can handle 100 Vrms and 1 A, with up to 3 W maximum power. Choose from the durable connector block or standard cable connections.
-
product
PXI 3-Channel 10A Solid State SPST Switch
40-182-012
The 40-182-012 has 3 off high current SPST switches in one PXI slot and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 10A of continuous current and switch up to 200V signals. The switch can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
Alternate 1.10 (31.18) - 7.20 (204.00) Switch Probe
TSP100-FK180-2
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
product
PXI Microwave Transfer Switch, Single, 26.5GHz, 50Ω, SMA
40-782B-531
The 40-782B-531 (PXI) and 42-782B-531 (PXIe) single transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50Ω and a maximum operating frequency of 26.5GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
product
PXI/PXIe RF Switch, Octal SPDT, Terminated, 8GHz, 50Ω, SMA
40-880B-004
The 40-880B-004 (PXI) and 42-880B-004 are octal SPDT 50Ω RF switches with 8GHz bandwidth. The 40/42-880B range have automatic termination of unused signals and are available as a dual switch in a 1-slot, a quad switch in 2-slots or hex and octal switches in 3-slots.
-
product
Microwave Switches
SMX-7XXX (Microwave)
The AMETEK VTI Instruments SMX-7000 Series of microwave switch cards extends functionality typically reserved for dedicated stand-alone systems into the PXIe from-factor. Single and dual slot configurations provide the ability to mix and match multiple switch configurations including SPDT, SP4T, SP6T and Transfer. Embedded virtual schematic control further simplifies setup and debugging allowing all relays to be engaged independent of application software and device drivers. Ideally suited for medium-to-high density automated test equipment (ATE), the SMX-7000 Series deliver uncompromised measurement integrity ideal for the most demanding aerospace, defense and communication applications.
-
product
PXI Dual 2 Channel (M Mode) ST 62.5 Cons
40-855-522-M62.5
Fiber Optic MEMS Switching cards available in many high density formats with a choice of five different connector styles to suit most applications
-
product
PXI Octal SPDT RF Switch 6GHz 50 SMA Terminated
40-880-004
A range of 50Ω SPDT RF switching with automatic termination of unused signals. Available as a dual switch in a 1 slot PXI module, a quad switch in a two slot PXI module or hex and octal switches in three slot PXI modules.
-
product
PXI Fault Insertion Switch, 7-Channel, One Fault Bus, 20 A
40-193A-001
The 40-193A-001 is a 7-Channel Fault Insertion switch with one fault bus, designed for the simulation of fault conditions in automotive systems. The module is capable of switching current up to 20A.
-
product
Ultra High Density Matrix Switch Card
1260-45
The Astronics 1260-45 offers the highest-density switching matrices in a single-slot C-size VXI module, configurable as 11 different matrices from four 4x16 2-Wire to one 16x16 two-wire. Easily extend this module externally to build a larger matrix in a single VXI chassis to satisfy even the most dense applications.
-
product
PXI Triple SPDT RF Switch 3GHz 50 SMB
40-870-003
The 40-870 is a 50 RF Switch available with 3 or 6 separate SPDT relays in a single PXI slot. Both versions exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40-870 has been minimized by careful attention to the mechanical and electrical design.
-
product
Switch Modules - 16 Single Pole Relays Arranged as an 8x2 Matrix
JX16/AB-1
This module has 16 single pole relays arranged as an 8x2 matrix as shown in the figure to the left. The matrix may be operated and wired individually for up to 16 8x2's per chassis, or jumpered to the backplane to form up to a 128x2 matrix. It is available with Type S or M reed relays for high speed, long life application. These modules are usually used for 2 wire testing where high and low meter leads must be switched between any two points. Often used for 2 wire LCR meter measurements, cable testing, or open / short testing in a variety of applications.
-
product
LXI Microwave Switch, 50Ω 4xSP6T & 3xSPDT Terminated, 40GHz SMA
60-890-005
Model 60-890-005 is a mixed configuration LXI Microwave Switch and is suitable for switching 50Ω signals up to 40GHz. With 4 banks of terminated SP6T and 3 banks of SPDT unterminated relays, it is ideal for constructing complex microwave switching systems for many applications. Connection is by high-performance front panel mounted SMA connectors.
-
product
PXI Hybrid Coaxial Switch: DC to 40 GHz, Dual SPDT, Unterminated
M9155CH40
M9155CH40 PXI Hybrid Coaxial Switch: DC to 40 GHz, Dual SPDT, Unterminated
-
product
PXI/PXIe RF Switch, Hex SPDT, 3GHz, 50Ω, SMB
40-870A-006
The 40-870A-006 (PXI) and 42-870A-006 (PXIe) are 50Ω RF switches with 6 separate SPDT relays in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40/42-870A has been minimized by careful attention to the mechanical and electrical design.
-
product
PXI Flexible Microwave Module, Dual SP4T 40 GHz, Single SPDT 40 GHz, 50 Ω, SMA
40-890-001
The 40-890 (PXI) and 42-890 (PXIe) range of PXI microwave modules allows users to specify the mix of relay types, frequencies and quantities based on the application requirements within the capabilities of the module driver card. Choose from the extensive relay selection already available in the Pickering microwave range to create a flexible solution.
-
product
Switch Modules - 32 Two Pole Relays Arranged as Four Separate 8x1 Multiplexers
JX32/4(1x8)-2A
This module has 32 two pole relays arranged as four separate 8x1 multiplexers as shown in the figure. The muxes may be operated and wired individually for up to 64 8x1's per chassis, or jumpered together to form 16x1's or 32x1's or jumpered to the backplane to form up to a 512x1 mux or two 256x1 muxes. It is available with Type A, Armature relays only.
-
product
PXI 17 x SPDT RF Switch 1.2GHz 50 SMB Connectors
40-754-117
The 40-754 is a 50Ω High Density RF switch available with 17 or 9 SPDT relays in a single PXI module. The 40-754 is available with two connector options; an SMB connector that provides a frequency range of 1.2GHz (useable to 1.8GHz) occupying two PXI slots, or an MS-M RF multiway connector which limits the bandwidth to 500MHz but offers a high density solution occupying one PXI slot. The RF switch design is identical in each case.
-
product
PXI Single 2 Channel (M Mode) SC 50 Cons
40-855-212-M50
Fiber Optic MEMS Switching cards available in many high density formats with a choice of five different connector styles to suit most applications
-
product
Keysight 32-Channel FormC/Form A General Purpose Switch for 34980A
34937A
The Keysight 34937A is a general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 28 independent single-pole, double-throw (SPDT) 1A relays and 4 single-pole, single-throw (Form A) 5A relays. This module is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. The Form C channels are 300V, 1A contacts and can handle up to 60W, and the Form A channels are 30VDC/250VAC, 5A contacts and can handle up to 150W. Standard 50-pin Dsub connectors allow for use with standard cables, terminal blocks, or mass interconnect solutions.
-
product
Standard 1.10 (31.18) - 4.80 (136.00) Switch Probe
TSP100-F180-1
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
product
Standard 1.10 (31.18) - 4.80 (136.00) Switch Probe
TSP100-H180-1
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
product
PXI 16 Channel Switch Simulation Module
40-480-121
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
product
PXI Microwave Transfer Switch, Dual, 26.5 GHz, 50 Ω, SMA, Failsafe, Remote Mount
40-782B-532-E
The 40-782B-532-E (PXI) and 42-782B-532-E (PXIe) dual failsafe transfer switches with remotely mounted relays are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 26.5 GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
product
PXI 8 Trib Daisy Chain Switch 75 Ohm 96 Way
40-792-701
The 40-792/793 Daisy Chain Switching Module is designed for telecom test applications. It allows production or verification testing of SONET/SDH transmission multiplexers switching 2MBit/s or 1.5MBit/s data. Traffic is sequentially Daisy- Chained through all tributaries (or any selection of tributaries), modules can be cascaded to test any number of tributaries.
-
product
PXI Solid State Switch Module, 6xSPST, 10 A, Hardware Interlock
40-182A-011-HI
The 40-182A-011-HI has 6 off high current SPST switches with hardware interlock in two PXI slots and is part of our range of high power solid state switching solutions.
-
product
Turnkey LXI Microwave Switch And Signal Routing Subsystems
We have the expertise and ability to turn your high-level requirements for a microwave switching subsystem into the fully integrated solution that you need. You provide us with your unique configuration and specification, and our engineers will work closely with you to provide a well-defined, fully integrated and supportable end product that will satisfy your microwave testing needs.
-
product
PXIe Flexible Microwave Module, Dual SP6T 40 GHz, Single SPDT 40 GHz, 50 Ω, SMA
42-890-005
The 40-890 (PXI) and 42-890 (PXIe) range of PXI microwave modules allows users to specify the mix of relay types, frequencies and quantities based on the application requirements within the capabilities of the module driver card. Choose from the extensive relay selection already available in the Pickering microwave range to create a flexible solution.
