-
Product
Modular Functional Testing Platform
OTP2
-
Functional testing is an important part of product development and manufacturing and is used to ensure quality, performance and reliability from launch to end of life. A modern, future-proof functional test system must meet many criteria in order to meet the ever-growing demands of the industry. The OTP 2 open test platform developed by LXinstruments meets the following requirements for a dynamic and highly competitive market.
-
Product
RSE Wireless EMC Spurious Emission
TS8996
-
The R&S®TS8996 RSE test system is designed for EMI and radiated spurious emission testing on wireless devices in semi-anechoic or fully anechoic chambers. The modular design makes it easy to extend the system to include new communications technologies. Typical devices under test include mobile phones or radio sets along with radiated measurements of other short-range devices. Standards require a wide range of test setups and a wide and high frequency range (up to 40 GHz). ESW or FSW frequency ranges are extended up to 325 GHz with option B21 using receive units TC-RSE for 5G FR2. Dedicated RSE test routines are also covered for this frequency range.
-
Product
Image Sensor Testing
IP750Ex-HD Family
-
The IP750EX-HD has been the test platform that has enabled the industry to manufacture high quality CCD and CMOS image sensors, and it is the most economical platform to meet the needs of newer technologies such as Time of Flight (ToF) sensors. When you use a smartphone, high performance digital still camera, or in-home security and surveillance system, these applications have image sensors most likely tested by Teradyne’s IP750ExHD.
-
Product
Laser Diode Burn-in Reliability Test System
58604
-
The Chroma 58604 is a high density, multi-function, and temperature controlled module for laser diode burn-in and lifetime tests. Each module has up to 256 SMU channels which can source current and measure voltage in various control modes as described below.
-
Product
High-Voltage Test Device
PGK 70 HB
-
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Testing of medium- and high-voltage cables* DC voltage testing of up to 70 kV output voltage with positive or negative polarity* AC voltage testing - up to 55 kV for switchgear, busbars and insulating elements* Easy-to-maintain 2-piece design
-
Product
HV Test System up to 20000 Volt
-
Insulated test booth with large space for test items. 2 banana sockets for AC connection and 4 banana sockets for the DC connection of the DUTs. IC’s are tested in a long-term test. These are checked in an oil bath so that there are no air gaps to reduce the insulation. Maximum voltage 20 kV. Therefore, insulation tests must be carried out. Ensuring the standard-compliant test. For the safety of the operating personnel, the test cell is electrically locked while the high voltage measurement is active.
-
Product
Drive Controller Function Test – Universal Functional Test System for Industrial Electronics
-
General functional test system based on LXI instrumentation for high mix / low to medium volume manufacturing. DUTs are tested which are mainly used as communication and measurement modules in power plant technology, grid management and electrical drives.
-
Product
VXI Digital Multiplier
4152A
-
The 4152A’s advanced features like limit testing, averaging, speed/resolution trade-offs, and fast function changes provide the high “test system” throughput required in today’s production test environments.
-
Product
DC High-Voltage Test Device
PGK 80
-
Cable testing and diagnostics with the BAUR PGK 80. The portable, one-piece PGK 80 high-voltage test device for generating negative DC voltage up to 80 kV is primarily used for onsite testing of paper-insulated mass-impregnated cables in the medium-voltage network. The high voltage is generated through a high-voltage transformer with secondary voltage-multiplier. The internal operating frequency of 20 kHz enables the smallest of device dimensions.* Continuous adjustable output voltage* The voltage measurement is done directly at the high voltage output* Timer of 1-30 min* Sensitive current measurement for recording the smallest of insulation currents with 6-time range switch, decadal
-
Product
EBIRST 200-pin LFH To 160-pin DIN Adapter
93-002-410
-
eBIRST adapters allow extension to other switching system connectors, including SMB
-
Product
Fully Programmable Digital Design with Wireless Remote Control
VLF E Series
-
The VLF E Series uses a state-of-the-art, switching power supply design with wireless computer controls. Equipped with HVI’s E-Link software, the E Series stands among the most advanced cable testing systems available. Our customers praise its flexible data capture and reporting capabilities, full remote operation via XBee wireless technology, and seamless tan delta testing with HVI’s TD units.
-
Product
Test System for Detecting Exact PCB Short Circuit Locations
QT25
-
Qmax Test Technologies Pvt. Ltd.
QT25 employs a unique method to detect exact PCB shorts circuit locations and pin down the shorted components and tracks. It is designed in such a manner that it precisely detects exact short circuit locations across VCC - GND or a shorted component connected across a Bus or hair-line shorts between PCB tracks, Which is highly impossible to detect using conventional tools especially when they are connected parallel in circuit. It can also be used in measuring the contact resistance of switches and relays in its milli-ohm mode as a value add.
-
Product
Positioning Test System
TS-LBS
-
The R&S®TS-LBS is a comprehensive test solution for network and satellite based location technology testing of wireless devices and chipsets.It is highly configurable for testing various location technologies and uses Rohde & Schwarz location based test systems.The R&S®TS-LBS test system family fulfills the requirements of LBS conformance testing and operator acceptance testing on GSM, WCDMA, LTE and 5G devices and chipsets as well as regulatory testing consisting of adjacent channels and spurious emissions for EN 303 413 receiver testing. It also fulfills the requirements of E112 (EU) 2019/320 testing consisting of GNSS testing such as Galileo and AML mobile testing.
-
Product
Wafer-Level Parametric Test
-
Wafer-level reliability engineers need to reduce test time without sacrificing measurement quality and accuracy.
-
Product
High Throughput 1 ns Pulsed IV Memory Test Solution
NX5730A
-
Precise and fast characterization of new memory, such as spin transfer torque magneto resistive random access memory (STT-MRAM) from DC to high-speed pulsed IV measurement on silicon wafers Apply accurate and high-speed pulsed voltages (down to 1 ns pulse) to magnetic tunnel junction (MTJ) for STT-MRAM and precisely measure the resistance of MTJ Perform all typical MTJ characterization tests in one solution10 to 100 times faster cycle test, such as a bit error rate test (BERT)Capture and visualize MTJ switching waveforms clearly during the writing pulse Dedicated solution with Keysight Technologies’ technical expertise
-
Product
Cable Assembly, 200-Pin LFH, Female (Male Screwlocks) to Female (Male Screwlocks), 2m
A200LFR-200LFR-6B200
-
This female to female 2m cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cable and the connector assemblies can be secured to their mating connectors by male screwlocks.
-
Product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Tinned Ends, 2m, HV
A037DF4-T-HA200
-
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Micro Dsub GPIB Cable For PZ2100A (1m)
PX0114A
-
The cable converting MicroD25 GPIB to standard GPIB; compatible with the Keysight PZ2100A
-
Product
Cable Assembly, Receiver, TriPaddle & Mini Coax, 20" to 9-Pin DIN, 3 BNC Plugs & 2 SMB Plugs
540096010111
-
Cable Assembly, Receiver, TriPaddle & Mini Coax, 20" to 9-Pin DIN, 3 BNC Plugs & 2 SMB Plugs
-
Product
Cable Assembly, Receiver, Mini Coax, 20", 20 SMB Plugs
540075010109
-
Cable Assembly, Receiver, Mini Coax, 20", 20 SMB Plugs
-
Product
Cable Assy 68-Pin SCSI Micro-D M/M 1m
40-970A-068-1m-MM
-
The 68-Pin SCSI Style Micro-D Cable Assembly is constructed from 7/36 (28AWG) Copper Wire with Polypropylene insulation. Metal Spring Latches are provided to secure the connectors to their associated products.
-
Product
Cable Assembly 15-Pin D-Type, Male to Male, 0.5m
40-970-015-0.5m-MM
-
The 15-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire with PFA insulation. Male screwlocks are provided to secure the connectors to their associated products. The 15-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Scienlab Charging Discovery System (CDS) – High-Power Series
SL1047A
-
The Scienlab Charging Discovery System – High-Power Series from Keysight enables you to test charging interfaces of electric vehicles (EVs) and EV supply equipment (EVSE) during high-power charging up to 1,500 V DC and ±600 A DC. With the CDS can perform all necessary conformance and interoperability tests according to worldwide charging standards. Our new solution, which features the separate Scienlab Cooling Unit with interchangeable liquid-cooled charging adapters, also enables a high-power upgrade of the SL1040A Scienlab Charging Discovery System - Portable Series.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Cut Ends, 1m HV, Exit Towards Pin 1
A050DM5-C-HA100
-
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
Cable Assembly, Receiver, TriPaddle 256, 36", 3 68-Pin Male VHDCI
540307020205
-
Cable Assembly, Receiver, TriPaddle 256, 36", 3 68-Pin Male VHDCI
-
Product
Cable Assembly, 200-Pin LFH, Female (Male Screwlocks) to Female (Male Screwlocks), 1m
A200LFR-200LFR-6B100
-
This female to female 1m cable assembly does not connect directly to Pickering Interfaces products that use the 200-Pin LFH connector, but customers may find it useful in the development of their own connection solutions. It is constructed from 4 bundles of 50-wire round/flat ribbon cable and the connector assemblies can be secured to their mating connectors by male screwlocks.
-
Product
Physical Layer Test System
N19301B
-
The N19301B Physical Layer Test System (PLTS) 2022 software is a powerful signal integrity tool for today’s high-speed digital designers.
-
Product
T7 Fiber-Optic Cable Assembly for GPIB-140, 100 m
182805-100
-
2-Pin Male to 2-Pin Male, Core/Clad 62.5/125 um, 850 nm Wavelength Fiber-Optic Cable for GPIB-140A Extender - The GPIB T7 Cable, sometimes referred to as GPIB Cable, connects your system to high-speed GPIB-140A extender devices. You can use the GPIB T7 Cable with a GPIB extender to increase the cable length of your system up to 1 km without comprising the integrity of your GPIB system or requiring any application modifications. The GPIB T7 Cable is offered in different lengths.
-
Product
Two Mini Alligator Clips to 1-Pin, Female SMB, 50 Ohm Coaxial Cable
763388-01
-
Two Mini Alligator Clips to 1-Pin, Female SMB, 50 Ohm Coaxial Cable - The SMB-Mini AC Coaxial Cable, sometimes referred to as SMB-300, connects measurement and signal devices. It is a 50 Ω cable.
-
Product
SH37F-P-4, 37-Pin Female to Pigtail Shielded I/O Cable, 12ft
778620-04
-
37-Pin D-SUB Female to 37-Pin Bare Wire Female, 12 ft, Pigtail I/O, Shielded Multifunction Cable - The SH37F-P-4 connects compatible CompactRIO modules to accessories or cables with bare wire connectors.
