-
Product
ALL-OUTDOOR RADIO SYSTEM
FreeMile 5 GE
-
SAF FreeMile 5 GE MIMO all-outdoor system is a Licence-free 5 GHz gigabit radio for Ethernet packet data transmission. Making use of ground breaking 2x2 MIMO technology, the SAF FreeMile 5 GE MIMO delivers up to 210Mbps (105Mbps full-duplex) of real throughput combined with a high packets-per-second performance.
-
Product
JTAG Boundary-Scan Controllers for High-Volume Production Systems
-
Corelis has designed special hardware that autonomously performs concurrent (gang) testing and programming of multiple units without additional user intervention. The entire testing and programming, including on-the-fly verification of results, is done in modular and expandable hardware.
-
Product
Test Case Management System
Kiwi TCMS
-
The leading open source test case management system. *Efficiently manage test cases, plans and runs*Improve testing productivity & reporting*Integrates with popular issue trackers*External API interface*GPL 2 licensed
-
Product
Basic Digital Systems
-
The Medical Imaging System can be configured simply by installing the FCR Reader, the CR Console, and the Imager to your existing X-ray equipment. The Imager uses the dry film for output and therefore does not require a dark room as in conventional systems thus saving space. Also, the scanned image can be digitally saved to media and not on films, thus not much storage space is required.
-
Product
Integrated I-V Test Systems
-
The OAI Integrated I-V Test System is perfect for R&D as well as production, the OAI Integrated I-V Test System delivers extremely accurate solar cell performance measurement. OAI’s advanced fully Integrated I-V Test System is designed to overcome the limitations of flash testing by providing a highly optimized pulse width and voltage sweep rate to match any type of solar cell’s high capacitance and slow dielectric response speed. As a result, the system produces extremely accurate measurements of solar cell I-V parameters and efficiency while leading to the most accurate test results.
-
Product
Battery Testing System
C8000
-
The Cadex C8000 stands in a class by itself in flexibility and affordable price. Test SMBus batteries, monitor cell balance and capture load signatures to observe batteries with a unique load protocol. Add a thermal chamber, an external load bank, a safety circuit and alarm to form a command center and you begin realizing the unique qualities of this fine battery testing system.
-
Product
Wafer and Cells PL System
HS-PL
-
Photoluminescence (PL) Imaging is a unique non-invasive inspection tool as it can be used in-line at many different steps of the cell manufacturing process. This facilitates the direct comparison of data obtained at one process step to data obtained at another. Additionally, PL imaging can be compared to electroluminescence (EL) imaging on finished cells using comparable equipment.
-
Product
Universal Measuring System
UMS4
-
Measuring device and data logger in oneAcoustic display of measured variablesBeep signal when limit value is exceededSerial interface for data transmissionConvenient data management with the DATA-UMS PC programDisplay and control through comfortable menu interface
-
Product
Analytical SFC System Configurations
SFC-4000 Series
-
The SFC-4000 analytical SFC is extremely flexible, and with multiple solvent options enables rapid screening of a range of columns using different solvent conditions completely automatically. The SFC-4000 has an option for up to three column ovens each with ten full-sized columns; each with separate temperature control, great for combining chiral and achiral SFC in a single system. Take advantage of a PDA detector combined with the CD-4095 chiral detector to work up fast analytical methods for direct scale-up to semi-prep and prep separations of chiral compounds.
-
Product
Jetting System
IntelliJet®
-
The IntelliJet® Jetting System with patented ReadiSet® Jet Cartridge delivers cutting-edge reliability and micro dot dispensing for manufacturing advanced semiconductor and mobile electronics packages
-
Product
Portable Metal Detection System
XT 8000
-
The new XT 8000 portable walk through metal detection system is a full featured digitally controlled unit that can be deployed in less than five minutes, yet stores away in a rugged carry bag for easy transport. Only $3,995.00 eachBuy NowOur Price $3,995.00 The new XT 8000 portable walk through metal detection system is a full featured digitally controlled unit that can be deployed in less than five minutes, yet stores away in a rugged carry bag for easy transport.XT 8000 is simple to set up and operate without specialized training. The system can be moved regularly to different facilities to provide security and deterrence while costing thousands less than permanently installing units at each site.
-
Product
Power Supply System
PL508
-
The PL508 is a high sophisticated, high density, programmable 8-channel moderate floating low-voltage power supply system. Using the remote monitoring and control features it can be used to supply a large numbers of external load-channels with high power consumption also over long distances.
-
Product
Vibration Diagnostics System
VDS
-
The Vibration Diagnostic System (VDS) is a vibration data management system designed specifically for the machinery Predictive Maintenance (PdM) community. It harnesses the graphic display capabilities of Crystal Instruments EDM Software for the work of machinery vibration analysts.
-
Product
Circuit Breaker Test System
TDR9100
-
The Doble TDR9100 Circuit Breaker Analyzer is a state-of-the-art circuit breaker test set for testing all types of circuit breakers with efficient and accurate performance measurements.
-
Product
Rugged, Small Form Factor Networking Systems
-
Curtiss-Wright Defense Solutions
Our field-proven, rugged switches and routers enable mobile networks on-board vehicle and aircraft platforms to securely and affordably deploy digital network architectures for situational awareness and network-centric operations.
-
Product
Ionic Contamination Test System
Omegameter SMD 650
-
The SCS Omegameter SMD 650, the long-time industry standard for ionic testing utilizing “static test” methodology, is designed to perform cleanliness testing on printed circuits and assemblies. Identifies the presence of ionic contamination on bare and assembled printed circuit boards and other electronic components. Provides an accurate and repeatable method for determining cleanliness on site. Provides immediate process control results, eliminating the need for outside laboratory testing.
-
Product
Automotive Electronics Functional Test System
TS-5020
-
The Keysight TS-5020 Automotive Functional Test System is a low cost, scalable test system designed with “just-enough-test” concept for medium complexity electronic control modules, such TPMS, RKE and body electronic modules
-
Product
National Instruments System Integrator
-
Knowledge of all National Instruments platforms and its wide experience in using and integrating NI hardware (CompactRIO, sbRIO, PXI, CAN, DAQ, etc.) and software (LabWindows/CVI, LabView e TestStand), IPSES offers to its clients customized solutions and services, providing both technological and economic benefits.
-
Product
Half Shaft Torque Measurement Systems
-
Advanced Telemetrics International
ATi’s Half Shaft Telemetry System transmits torque signals from rotating shafts to a stationary telemetry receiver. It connects directly to strain gages adhered to the shaft converting it into a torque sensor allowing it to transmit shaft torque while the vehicle is operating. This system is a testing tool used by automotive and racing engineers to obtain real-time torque measurements from vehicle drivelines.
-
Product
Hydrostatic Test Stand, Hydraulic System Components
9901HTX-100LR2-36x36x15
-
The 3 ft. wide x 3 ft. deep Hydrostatic Test Stand, Hydraulic System Components is utilized for pressure testing hose and tube assemblies as well as any component requiring hydrostatic testing in the integral safety test chamber.
-
Product
RFID Test System
-
RFID test system of Peritec is making FPGA board (IF-RIO) the processing of the IF band. This reading of the code, called (Electronic Product Code) EPC is required for RFID tag ISO18000-6 TYPEC of (EPC C1 G2). However, it did not provide treatment too late in the traditional instruments.
-
Product
Barcode Verification Systems
REA PC-Scan LD4
-
The REA PC-Scan LD4 is a barcode verifier made in Germany which was developed in conformity with international standards. It is especially designed for measuring barcodes with highest precision. The combination of state-of-the-art technology, process reliability and intuitive operation makes the REA PC-Scan LD4 globally unique in its class. Final statements "Pass" or "Fail" are central display elements and enable an immediate result. The simultaneously displayed details allow for an immediate and exact barcode quality analysis.
-
Product
Dosage System
Okhta
-
The "Ohta" system is designed for automated dosing of bulk materials. By controlling the dispenser valve based on feedback from digital scales, the system optimizes the operation of filling and packing machines with manual control of the dispenser valve, which reduces the number of underweightes. The hardware of the complex is built on the basis of the industrial platform CompactRIO of National Instruments. The user interface and software for statistical processing and analysis of the received data are realized on a tablet computer that interacts with the controller via the WiFi interface.
-
Product
Upstream-Measurement-System
AMA 310 UMS & VAROS 107
-
This system combines the KWS devices AMA 310/UMS and VAROS 107 to a high-end monitoring system for the return path frequency range. An AMA 310 in a 19-inch version (3.5 RU) with UMS module is used in the headend, in the field the CATV handheld VAROS 107 is the counterpart.
-
Product
Circuit Breaker Analysis System
-
Weshine Electric Manufacturing Co., Ltd
1. Time measurement: 12 fracture intrinsic points, closing time, with the same period, phase with the same period.2. Reclosing measurement: each fracture closing - minute, minute - closing, minute - closing - minute process time, one minute time,one closing time, two closing time, gold short time, no current value.3. Bounce measurement: closing bounce time, bounce times, bounce waveform of each fracture, rebound amplitude of each fracture.
-
Product
VLF Testing and Diagnostics System
PHG 70 TD/PD
-
Cable testing and diagnostics with the BAUR PHG 70 TD/PD. With the PHG TD/PD, you get a multifunctional cable testing and diagnostics system that was specially designed and developed for medium-voltage networks. The PHG TD/PD system is also the only cable testing and diagnostics system that gives a comprehensive overview of the quality and ageing condition of the test sample. The diagnostic methods TD and PD are mutually complementary, because on one hand you can detect the complete condition and on the other hand locate * individual faults in the operating resources.* High performance VLF truesinus testing device (3 kW) with regulated output voltageCompact, enclosed design in 19" format* Variable installation option with separate control and voltage unit* Variable connection options to cable stations of different models
-
Product
Lamp Cap Temperature Rise Test System
TMP-L
-
TMP-L is according to IEC60360-1998 and GB2512-2001 (Standard method of measurement of lamp cap temperature rise). It is used to test the working and environmental temperature as well as temperature-rise of the burner and lamp. It meets the requirement of IEC and GB Standards.
-
Product
High-Performance Surface Plasmon Resonance System
SPR-32
-
Features like ‘Frame Inject’ allows for turn-key sample processing protocols and customized workflows created together with pharmaceutical customers. The faster data analysis and highly intuitive user interface combine to deliver an industry-leading SPR throughput of 10,000 control-substracted binding measurements. Combining flexible 8-needle sample delivery with a 32-sensor detection array laid out in 8 detection flow cells, enables 4 sensors per flow cell, an important advantage for controlled, high-throughput SPR methods. The patented Hydrodynamic Isolation™ technology enables ‘Any Sample, Any Sensor, Any Time’, making it the preferred platform for screening, kinetics, thermodynamics and epitope mapping for pharmaceutical applications.
-
Product
Universal Monitoring System
R&S®UMS400
-
The ever-increasing frequency range of wireless communications services calls for monitoring stations up to 8 GHz, in some cases even up to 20 GHz. Typically, this requires a monitoring sensor installed close to the antenna(s) in order to keep cable losses as low as possible for highest sensitivity. This is possible for both the R&S®UMS400 and R&S®CS-MC20, thanks to an outdoor housing.
-
Product
DC Voltage Test System
-
HIGHVOLT Prüftechnik Dresden GmbH
DC test systems are used to test components and complete systems found in electrical power supply systems and operating on DC voltage.
