-
Product
IEC60884 Fig8 Plug Strength Compression Tester
IEC60884 fig8
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 fig8 plug strength compression testerConforms to the standard: GB2099-1-2008 Articles 10.1 and 24.5 and Figure 8, IEC60884-1 Figure 8
-
Product
Moisture Meters
-
Traceable® Moisture Meter displays material, wood, wood product, and paper moisture content 9.0 to 30.0% with a resolution of 0.1% and an accuracy of ±(4% of the reading plus 5 digits). Memory contains nine material groups such as fiberboard, construction material, and calibrations for 150 types of wood. For all other products, user establishes reference moisture readings. Once programmed, the meter reports directly in percent moisture. Simply touch a material to measure moisture. Takes only seconds. Jumbo-size digits are 1-3/8 inches high.
-
Product
Signal Finder
-
Digital satellite finder, Digital satellite meter, HD DVB-S/S2, Demodulation QPSK, 8PSK, Display POWER、C/N、Quality value, Upgrade software & parameters through USB2.0 Port, Easy to read LCD.
-
Product
RF Test Spectrum Measurements over CPRI
Integris 3000
-
Most modern cell tower network configurations place the Remote Radio Head (RRH) at the top of the tower and the baseband unit(BBU) at the bottom of the tower. While this configuration is advantageous for both computational efficiency and mitigation of RF loss across the cable, it means the only place along RF can be accessed is at the top of the tower. This forces field technicians to have to climb the tower to measure and debug RF noise problems.
-
Product
Sky Quality Meter
SQM-LU
-
A USB SQM model for night-time sky brightness monitoring! An affordable meter for continual, connected measuring of sky brightness for astronomers! The "Sky Quality Meter - LU" measures the brightness of the night sky in magnitudes per square arcsecond.
-
Product
Digital Panel Meter
-
Shenzhen Star Instrument Co., Ltd.
Three-phase energy meter measures energy, voltage harmonics, current harmonics, voltage, current, power and power factor.
-
Product
2-Phase Stepper Drives Based On EtherCAT Field Bus
Nu-Step DA Series
Stepper Driver
The ADLINK Nu-Step DA Series is a stepper driver based on the EtherCAT bus featuring a 32-bit ARM processor and advanced variable current and frequency conversion technology. The driver generates less heat and motor vibration for more stable operation. It not only supports the standard EtherCAT specification, but also supports table comparison triggers for automated optical inspection (AOI) and linear comparison triggers for line scanning.
-
Product
RF Shielded Enclosure, 80dB Isolation Testing
QuietBox-80c/r
-
The Raymond RF QuietBox-80c/r line of all-aluminum tabletop and rack mountable RF Shielded Cabinets offers effective RF isolation in a lightweight, fully-customizable package. Each QuietBox 80c/r is designed from the ground up to satisfy all the requirements of the client including enclosure dimensions, door swing and mounting style (tabletop or rack mount).
-
Product
Vibration Meter
Revo
-
The Revo Vibration Meter has been specifically designed for Hand-Arm Vibration and Whole Body Vibration measurements.
-
Product
Third Party RF Amplifiers
-
We work closely with major manufacturers to supply a range of oscilloscopes, function generators and power amplifiers. We are the UK agent for the leading manufacturer of RF amplifiers Electronics and Innovation.
-
Product
Signal Sources
-
NSI-MI’s synthesized Signal Source devices provide fast, accurate and economical signal generation solutions for a wide range of test and measurement applications. These sources are designed to be used in test and measurement situations where speed is paramount. Sources can also be located remotely, to support our distributed solutions, making them ideal for all RF measurement applications.
-
Product
Signal Contacts
-
VPC’s signal contacts are high reliability, modular connectors used to route low voltage, low current signals within VPC’s mass interconnect test systems. They provide durable, high cycle electrical connections—via families such as TriPaddle and QuadraPaddle—supporting dense, configurable interfaces
-
-
-
Product
Frailty Meter
-
Wireless wearable system that is portable and easy to usePhenotype-based frailty assessment with independent measures of weakness, slowness, exhaustion, and range-of-motionBased on a 20-second elbow flexion-extension testCan be used for bed-bound patients, no standing or walking requiredDoes not depend on self-rated health and activity surveysValidated against the frailty phenotype (i.e., Fried Criteria) and the frailty index (i.e., modified Rockwood Frailty Index)
-
Product
Small Signal RF/Microwave Power Amplifier
-
R&K’s small signal amplifier series are to amplify various high frequency signals such as CW/Pulsed/AM/FM/N-DCMA/W-CDMA/OFDM , etc.
-
Product
Multifunctional Meter
AEM-DD
-
AEM-DD provide high accuracy DC power measurement,display and remote communication of five loops(V,A,P,Kwh). Multi-circuit designand relay output modular expansion design decrease the overall cost and make the functionality more flexible.
-
Product
TAP Signal Isolation Module
JT 2139
-
The JT 2139 is a TAP signal isolation module designed for use in combinational test systems that utilise multiple instrument interfaces. To avoid parasitic capacitance effects and/or unwanted ground loops the JT 2139 can be used to completely galvanically isolate any JTAG Technologies boundary-scan controller from the remainder of the instrumentation system. JT 2139 isolators are a standard component of the JTAG Technologies ‘Symphony’ systems that integrate boundary-scan with In-Circuits Testers etc..
-
-
Product
16-Channel Analog Multiplexer & Signal Conditioning Card
AIM-16
-
Model AIM-16 accepts, pre-amplifies, and multiplexes analog signals for application to an analog-to-digital converter installed in a host computer. Each AIM-16 concentrates 16 differential analog input channels into one single-ended analog output channel. Up to eight AIM-16s can be cascaded providing total capacity for 128 inputs to an "8-input A/D Converter."
-
Product
USB Oscilloscopes & Mixed Signal Oscilloscopes
PicoScope® 2000 Series
-
You can use your PicoScope 2000 Series as an advanced oscilloscope, spectrum analyzer, function generator, arbitrary waveform generator and protocol decoder out of the box. Mixed signal models also add a 16 channel logic analyzer. A complete electronics lab in one compact, low-cost, USB-powered unit.
-
Product
Adjustable Signal Samplers
7999
-
Now, you can extract a low signal level from a 50-Ohm coaxial system with the Model 7998 and 7999 series of Adjustable Signal Samplers from Coaxial Dynamics. These Signal Samplers are essential tools for spectrum analysis, RF signal scope observation, or frequency counting control.
-
Product
Disc Series Meters
-
Recordall Disc Series Meters provide an accurate, cost-effective solution for your residential metering needs. Combining the accuracy of positive displacement meters with the reliability and economy of nutating disc technology, the simple but efficient design of this meter makes it an ideal solution for measuring flow.
-
Product
AC/DC Current Clamp Meter
CM1000
-
Clamp opens up to 1 inch (25.4 mm). One rotary switch operation. Large 4 digit LCD display. AC/DC Voltage measurement up to 1000 Volt. AC/DC current measurement up to 1000 A. Relative measurement. One touch auto zero. Peak Hold Function. Data Hold Function
-
Product
Luminance Color Meters
-
Konica Minolta Sensing Americas, Inc
Similar to Illuminance meters, luminance color meters are three element detectors that both measure photometric brightness falling upon a surface, as well as give color information.
-
Product
MXG Signal Generators
-
On the path to better performance, the Keysight's MXG signal generators are fine-tuned signal sources in R&D measurements. Whether you’re pushing for a linear RF chain or an optimized link budget, the analog and vector MXG models deliver the performance and capabilities you need: phase noise, ACPR, channel coding, and more.
-
Product
Gloss Meters
-
Small, lightweight and durable the gloss meter can be used in production and laboratory environments. The high specifications, including statistical analysis, graphical analysis and software-free PC down load facility make it the ideal gloss meter for matt to mirror surface finishes
-
Product
Mixed Signal JTAG Tester
JT 5705
-
The JT 5705 series offer a unique combination of JTAG TAP controller (tester) interfaces plus digital and analog I/O in compact desktop package.Use the ‘mixed-signal’ features to measure power supplies, clock frequencies or test DACs and ADCs. Add your own capability through use of CoreCommander FPGA our generic bridge/translator system.
-
Product
Desktop Meter Test Station
WECO 300
-
The WECO-300 Desktop Meter Station offers advanced features, highest quality at exceptional value. A truly compact portable desktop station weighing in at only 16.5 lbs. the WECO-300 provides a safe environment to perform a wide range of functional meter tests.
-
Product
Remote Metering Station
GP200
-
GP200 remote metering stations expand production capabilities by increasing delivery points of existing melters with metered add-on precision. They provide an economical alternative to purchasing an additional melter, converting from non-metered delivery, or adding application points.
