-
Product
PCI 16xSPDT 2Amp Relay Card
50-131-001
-
The 50-131-001 16xSPDT relay module is part of our range of PCI, low cost, general purpose electro-mechanical relay modules which are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching modules do not have sufficient voltage or current carrying capability.
-
Product
3U CompactPCI Mini PCI, Mini PCIe Carrier Board
cPCI-3W10
-
- Supports 32bit, 33/66MHz CompactPCI® bus- One SIM card socket- One Mini PCI and one Mini PCIe socket- PICMG® 2.0 R3.0 compliant
-
Product
High Speed PCI Data Acquisition Processors
DAP 5400a
-
The DAP 5400a model, a board optimized for simultaneous sampling at extreme speeds, has eight A/D converters that sample simultaneously with 14-bit resolution at 1.25M samples per second each, for a total throughput of 10M samples per second. Or for higher speeds per channel, each board can sample each of 4 channels at 2M samples per second.
-
Product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 8 Channel
50-201-008
-
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
Product
PCI Precision Resistor Card 9-Channel, 2Ω To 102kΩ
50-297-034
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Multi-Channel 1553 Interface for Single Lane PCI Express Systems
PCIE1L-1553
-
Alta Data Technologies’ PCIE1L-1553 interface module is a multi-channel (1-2), ½ size, Low Profile, One Lane PCI Express 1553 card with the latest software technologies. The PCI Express card is based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This package provides increased system performance and reduces integration time.
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 3Ω To 52.4kΩ
50-298-133
-
The 50-298-133 is a high density programmable resistor card with 4 channels which can be set between 3Ω and 52.4kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI-8433, 4-Port, PCI, Isolated, RS485/RS422 Serial Interface Device
779146-01
-
The PCI‑8433/4 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
PCI Express
-
Welcome to PCI Express (PCIe) Learning Center. As PCIe interconnect is becoming increasingly popular as a common data bus standard, we has created this one-stop-page for you to know everything about PCIe. Get updates on the latest PCIe standard specifications, learn how to take jitter measurements and discover PCIe timing solutions and design tips. Become a PCIe expert yourself!
-
Product
PCI High Density Pecision Resistor Card, 9-Channel, 3Ω To 52.4kΩ
50-298-033
-
The 50-298-033 is a high density programmable resistor card with 9 channels which can be set between 3Ω and 52.4kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI 2 Amp Multiplexer, Dual 4-Channel, 4-Pole
50-635A-107
-
The 50-635A-107 is a dual 4-channel, 4-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PCI Synthesizer
SYNTH300 Series
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
Product
Flexible x1 PCI Express to MiniPCI Express Adapter
SKU-056-02
-
The Flexible x1 PCI Express to MiniPCI Express Adapter (Adapter) was designed to convert the x1 PCI Express bus into the MiniPCI Express bus. It allows you to connect the MiniPCI Express expansion add-in board to the motherboard PCI Express connector.The Adapter includes a MiniPCI Express adapter board (downstream), x1 PCI Express host board and PCI Express flat cable.
-
Product
32-CH Isolated DIO PCI Cards
PCI-7230/33/34
-
ADLINK"s PCI-723X series are 32-CH isolated input and/or output cards which provide a 2,500 V optical isolation protection. The wide input range of the PCI-7230 and PCI-7233 makes it easy to sense the status of external devices. The non-polarity characteristic is suitable for a wide variety of industry applications. The PCI-7230 and PCI-7234 devices also feature a wide output range from 5 to 35 V, which is suitable for relay driving and industrial automation applications. The PCI-7234P provides current-source output capability. The PCI-7230 and PCI-7233 also provide two interrupt sources on digital input channels. The PCI-7233 also features a change-of-state (COS) function that generates an interrupt when any digital input changes its state.
-
Product
PCI High Density Resistor Card 5-Channel, 16-Bit, 0 To 65k Ohm
50-295A-021-5/16
-
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Controller PCI
IIB-429-PCI
-
The IIB-429-PCI provides four ARINC-429 compatable channels (2 receive and 2 transmit) at any rate between 12.5 and 100kbps. Because the IIB-429-PCI is built upon a flexible platform, user functions can be implemented almost without restriction, making this product flexible and user-friendly.
-
Product
PCI High Density Potentiometer Card 4-Channel, 12-Bit, 0 To 4k Ohm
50-296A-121-4/12
-
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
XMC-to-PCI Express Adapter
4822
-
The Technobox, Inc. P/N 4822 XMC-to-PCI Express Adapter permits the use of a single-wide XMC module in a 4x PCIe slot. PCI express lanes on the P15 XMC connector are routed to the male PCI express edge finger connector. The reserved future use, RFU, signals from P15 are available on one of the user connectors. The adapter also provides user access to all the signals on the XMC P16 connectors via two 64 pin headers UC1 and UC2.
-
Product
Compact PCI Bus Analyzer / Exerciser
CPCI650
-
The CPCI650 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation and fault generation- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics
-
Product
PCI Express 16 Isolated Input Digital Interface (10-30V)
8006He
-
Optimized for sensing up to 24V inputs, the 8006He PCI Express digital I/O interface provides 16 optically isolated inputs for connection to devices including sensors, switches, pushbuttons, and other user inputs. The inputs can sense both AC and DC voltage while providing optical isolation, which eliminates spikes and surges present in industrial environments. The board is PCI Express X1 compliant and is compatible with any PCI Express slot.
-
Product
PCI 2 Amp Multiplexer, Quad 16-Channel, 1-Pole
50-635A-008
-
The 50-635A-008 is a quad 16-channel, 1-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
COM Express Type 2 Starter Kit
-
The Starter Kit consists of a COM Express Type 2 core module with ATX size reference carrier board that offers one PCI Express graphics slot x16 , four PCI Express x1 slot, two PCI slots, Serial ATA, SDVO, VGA, LVDS, TV-out, USB 2,0, Gigabit LAN, and Super I/O. All necessary cables are included.
-
Product
PCI Extender Card for cPCI Systems
DP-cPCI-7497
-
The DP-cPCI-7497 is highly flexible PCI Extender card, which can be used to extend PCI / PCI-X bus from one system to another system over an optical fiber medium upto 500m distance. A PCI-X to PCI-e Bridge is used to convert the PCI / PCI-X protocol to x4 PCI Express protocol operating at 2.5Gbps.The PCI-X to PCI-e Bridge is connected to four optical transceivers (x4 PCI- e link) which can transmit optical signals upto 2.5Gbps speed.A x4 copper medium connection option in lieu of optical transceivers is also available.
-
Product
3U 7th Generation Intel® Core™ i5-7440EQ Processor-Based PXI Express Gen3 Controller
PXIe-3977
-
The ADLINK PXIe-3977 PXI Express embedded controller, based on the 7th gen Intel® Core™ i5 processor, is specifically designed for hybrid PXI Express-based testing systems, delivering maximum computing power for a wide variety of testing and measurement applications.
-
Product
6U Compact PCI® Single Board Computer
CP62001
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62001 is a 6U CompactPCI® single board computer designed based on Intel® GM45 chipset, compliant with PICMG®CompactPCI® specifications. There are SATAII, USB2.0, 10/100/1000Mb Ethernet, and Keyboard/Mouse interfaces on board. The display controller integrated in CP62001supports VGA and DVI dual output independently, with up to 2048×1536 resolution on CRT. Up to 4GB soldered memory on CP62001, leaves no worry about the board stability under harsh shock and vibration environment for end users. Besides, LinkedHope™ provides variant drivers BSP) support, such as VxWorks, Linux and Windows, as reduces the workload of system integration and the development of final solutions and shorten the Time-to-Market.The CP62001 with high performance/power ratio, works stably in extended temperature range, and is an ideal selection for high reliability and high availability required applications, like harsh environment communication, network security, video/image processing and can also be an ideal control unit in variant devices and equipment.CP62001 has a ruggedized version (called CP62002)with conduction cooling and wedge-lock technology. CP62002 is designed for extremely harsh environment.
-
Product
Single Front Slot Universal Low-Profile PCI to PCMCIA Adapter, Black Bezel
P313B
-
To cater to the latest generation of low-profile PCs that can only use low-profile PCI add-in boards, Elan has created the P313. This model, from the P-series range, features a PCMCIA Type III 3.5" drive bay mounted slot and a circuit board that conforms to the MD1 profile specification. It will allow you to use any TypeI/II/III PCMCIA card.
-
Product
PCI Multiplexer Cards
-
*High-density 4-bank, 24-channel, 2-pole multiplexers*2 Amp multiplexer range with 18 configurations between single 64-channel 1-pole and quad 8-channel 2-pole*High-density multiplexers with switching formats between 5-channel, 32-pole and 198-channel, 1-pole*High-voltage multiplexers designed for cable testing applications*Supported our eBIRST Switching System Test Tools, these tools provide a quick and simple way of finding relay failures our switch systems.
-
Product
PCI Precision Resistor Card 3-Channel, 2.5Ω To 201kΩ
50-297-141
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI 2 Amp Multiplexer, Dual 16-Channel, 1-Pole
50-635A-105
-
The 50-635A-105 is a dual 16-channel, 1-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
14 bit, 125 MS/s PCI Digitizer
ATS460
-
ATS460 has been designed from the ground up for OEM applications, which require very high reliability, high performance, high quality and reasonable prices. ATS460 uses COTS analog components and FPGAs to provide you more features and benefits and at the same time reduced manufacturing costs without compromising quality. The result is that you get more digitizer for less money.
