-
product
ARM Computer
SYS-398Q-2G-0
WINSYSTEMS’ SYS-398Q is an enclosed embedded computer system offering high-performance multimedia graphics and a rich industrial I/O mix. The NXP® i.MX6Q processor's integrated power management provides excellent power efficiency and allows operation from -40° to +85°C without active cooling. It is designed for demanding graphical applications in security, transportation, medical, and digital signage.
-
product
Gearbox Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
product
3.5" Single Board Computer With 13th Gen Intel® Core™ I7/i5/i3/ Celeron® Processor
SBC35-RPL
SBC35-RPL is powered by Intel's latest processors, which offer improved performance, power efficiency, and support for the latest technologies based on Intel's 13th generation of 3.5-inch Single Board Computers (SBCs) offer a range of advanced features and capabilities for a variety of embedded applications.
-
product
M/MA Module Carrier
VX405C
The VX405C carrier provides the mechanical and electrical interfaces between the VXIbus and up to six (6) VITA 12-1996 standard M/MA-Modules. The carrier provides VXI register configuration and access to the M/MA-Module I/O space and memory (if present). Each M/MA-Module is controlled separately and appears as a different logical address in the VXI environment. Over 100 M/MA-Modules are available that can provide custom interfacing to the unit under test (UUT). Up to six (6) unique interfaces may be provided in a single VXI slot.
-
product
Combination Board Testers
QT2256-640 PXI
Qmax Test Technologies Pvt. Ltd.
designed as a Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities for conventional PCBs.
-
product
Bare Board Tester
1232
High-Precision Batch Fixture-Type Testing System that Support Boards with Embedded Passive and Active Devices. The 1232 is a bare board tester that utilizes the full range of Hioki’s in-circuit testing technologies to deliver LSI reliability testing, complex component separation testing, high continuity and insulation testing, and more. (Double-sided alignment) Testable board dimensions: 50 × 50 to 330 × 330 mm (including clamp area) • Support for build-up boards that require resistance guarantees.
-
product
Terminal Board With 100-Pin SCSI-II Connector For General Purpose Servo & Stepper
DIN-825-4P0
- Supports specific servos & steppers by cable selecting- On-board connector type: 100-pin SCSI-II- Dimensions: 300 mm x 107 mm x 44 mm (W x L x H)
-
product
NI-9482, 4-Channel, SPST Relay, 60 VDC (1 A)/250 VAC (1.5 A) C Series Relay Output Module
783906-01
4-Channel, SPST Relay, 60 VDC (1 A)/250 VAC (1.5 A) C Series Relay Output Module - The NI‑9482 directly connects to a wide array of industrial devices such as motors, actuators, and DC devices. Each channel provides access to an electromechanical relay for switching signals up to 60 VDC (1 A) or 250 Vrms (1.5 A), features channel‑to‑channel isolation, and has a LED that indicates the status. The shock and vibration rating for the NI‑9482 is limited compared with other CompactDAQ and CompactRIO modules because of the mechanical relays on the module.
-
product
COM Express® Type 7 Reference Carrier Board in ATX Form Factor
Express-BASE7
The Express-BASE7 is an ATX size COM Express Type 7 reference carrier board. Together with the COM Express Type 7 module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
product
Burn-In Board Tester
Focus-275
Focus275 is a tester for burn-in board.It can improve reliability of burn-in board by inspecting boards for burn-in test by Focus275 regularlyBoth short open test and component test can be done by sending electric signals for special socket contactor and edge part.
-
product
120 GBd High-performance BERT
M8050A
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
product
3.5" Single Board Computer With Intel® N97 Processor
SBC35-ALN
SBC35-ALN, powered by Intel® N97 Processor, is exceptionally well-suited for a wide range of applications, specifically tailored for EV Chargers. This 3.5-inch Single Board Computer (SBC) from Intel's 13th generation excels in superior performance, power efficiency, and compatibility with cutting-edge technologies.
-
product
ARM Computer
SYS-398D-2G-0
WINSYSTEMS’ SYS-C398DL single board computer combines high-performance multimedia graphics with a rich mix of industrial I/O. The NXP i.MX 6DL processor’s integrated power management provides excellent efficiency and allows operation from -40° to +85°C without active cooling. It is designed for demanding graphical applications in security, transportation, medical, and digital signage.
-
product
PXI Express Optical FPGA Board
HSS-8324
The Conduant HSS-8324 Optical FPGA board provides the user with a hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its 24-lane optical interface. The PXIe interface provides a theoretical maximum throughput of 8GB/s (simultaneous in and out).
-
product
Combination Board Tester
ATE QT2256-640 PXI
Qmax Test Technologies Pvt. Ltd.
Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or micro controller based boards. ATE QT2256-640 PXI system is designed as a combination board tester capable of testing highly complex and PCBs employing various techniques on a single platform. It can be easily upgraded to 640 digital channels and with programmable UUT power supplies, IEEE or PXI external instrumentation, Bus cycle signature system, ICE and integrated Boundary scan Test AC/DC parametric testing. The ATE is interfaced to an external host PC using a PCI express interface card allowing a maximum data transfer rate. Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or microcontroller based boards.
-
product
Combination Board Tester
V250 / V250PXI
Qmax Test Technologies Pvt. Ltd.
V250 / V250PXI is designed as a Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform. It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities and conventional PCBs. An In –Circuit device test by configuring Pin Drivers to High Current Pin Driver mode and interface to the UUT either through Clips / Probes or nail bed and on board clock disable HW feature are the all time favorite . The in-built high frequency 14bit Analog Driver / sensors synchronized with digital drivers for covering analog / mixed signal devices with high degree of accuracy.
-
product
Board
ARDUINO UNO WiFi REV2
The Arduino UNO WiFi Rev.2 is the easiest point of entry to basic IoT with the standard form factor of the UNO family. Whether you are looking at building a sensor network connected to your office or home router, or if you want to create a Bluetooth® Low Energy device sending data to a cellphone, the Arduino UNO WiFi Rev.2 is your one-stop-solution for many of the basic IoT application scenarios.
-
-
product
Burn-in Board Continuity Tester
CT-1
Burn-in Board Coninuity Tester. Verifies burn-in board continuity and component tolerances. 768 I/O channels, can be forced to the constant current source or grounded independently. Highly accurate measurement of resistance, voltage, and capacitance using a pair of precision instrumentation amplifiers.
-
product
KVS Rugged Igniter Tester With Current Monitor
4314
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
product
3U OpenVPX ARM Cortex-A9
68ARM1
NAI’s 68ARM1 is a 3U VPX ARM® Cortex®-A9-based, Single Board Computer (SBC) that can be configured with up to three smart function modules. Ideally suited for rugged defense, commercial aerospace, and industrial applications, the 68ARM1 delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems.
-
product
Board
Arduino Micro
The Micro is a microcontroller board based on the ATmega32U4 (datasheet), developed in conjunction with Adafruit. It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a micro USB cable to get started. It has a form factor that enables it to be easily placed on a breadboard.
-
product
Hoist Tester
The system has the capability of operating hyraulic powered hoists, DC powered hoists and 400Hz AC powered hoists. When a unit is connected to the system it is automatically detected and the system will load the unit's control software, acceptance procedures and operational safety limits. By doing all of this the operator does not need to worry about anything other than installing the unit and clicking Run to execute a full test procedure.
-
product
Automated Bare Board Tester with Built-In Camera
QTOUCH2404C
Qmax Test Technologies Pvt. Ltd.
Qtouch2404C – Automated Bare Board Tester with in-built camera is designed to make automatic image capturing and probing of bare PCBs. It is designed to move on X,Y,Z directions making it possible to probe every test point. Flying Probe Tester is designed for testing high density fine pitched Single Sided / Double Sided and Multilayer PCBs for continuity and isolation using moving probes fixture –less technology.
-
product
PC/104 Single Board Computer
PCM-VDX-2
The PCM-VDX-2-512 is a 1GHz, fanless PC/104 single board computer based upon the ultra low power Vortex86DX processor with wired networking capability. This board requires about 6 Watts under full load while operating over an industrial temperature range of -40° to +85°C.
-
product
Distribution Board, For 8 N181x SPDT Switches
Y1150A / 34945EXT
Connects the 34945EXT to 8 N181x SPDT to route the power and control signals from the driver module to the switches
-
product
PCI/104-Express Type 1 Single Board Computer with 6th Gen. Intel® Core™ Processor (formerly codenamed Skylake)
CMx-SLx
The CMx-SLx is a PCI/104-Express Type 1 Single Board Computer (SBC) featuring the 64-bit 6th Gen. Intel® Core™ i3 processor (formerly "Skylake-H"), supported by the Intel® CM236 Chipset. The CMx-SLx is specifically designed for customers who need high-level processing and graphics performance in a long product life solution. The CMx-SLx Intel processor supports Intel Hyper-Threading Technology (i3-6102E = 2 cores, 4 threads) and 8 GB of soldered ECC DDR4 memory at 1866/2133 to achieve optimum overall performance.
-
product
Crease and Board Stiffness Tester
CBT1
The instrument measures crease folding force at 90°, board stiffness at 15° and requires no external software for operation. It automatically calculates the crease to board stiffness ratio for instant indication as to whether the material will run correctly on a high speed packaging machine.
-
product
Motion Control Terminal Board For Mitsubishi J2S-A Servo Amplifiers
DIN-812M0
- On-board connector type: 100-pin SCSI-II female- Suitable for Mitsubishi J2 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8132
-
product
Overhead Board
OVH-380-2
Curtiss-Wright Defense Solutions
The OVH-380-2 is the enhanced overhead board for the AIM/ HS-AVDAU-200XE. It stores and executes the operating system, application software and drivers, and terminates the IP stack for Ethernet support. It also receives and formats inbound (acquired) data.
