-
product
Instrumentation Amplifiers
Analog Devices instrumentation amplifiers (in-amps) are precision gain blocks that have a differential input and an output that may be differential or single-ended with respect to a reference terminal. These devices amplify the difference between two input signal voltages while rejecting any signals that are common to both inputs. The in-amps are widely used in many industrial, measurement, data acquisition, and medical applications where dc precision and gain accuracy must be maintained within a noisy environment, and where large common-mode signals (usually at the ac power line frequency) are present.
-
product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
product
Preamplifier, 100 MHz to 18 GHz
87405C
Exceptional gain (25 dB) and flatness (1.5 dB) combined with a probe-power bias connection which eliminates the need for an additional DC power supply, makes these preamplifiers the ideal choice for spectrum analyzer or stand alone applications.
-
product
Microwave Power Amplifier 1/4 Watt 10 MHz to 50 GHz
GT-1051B
The Spanawave/Giga-tronics GT-1051B Microwave Power Amplifier offers linear high-power amplification across muultioctive bandwidths. Ideal for testing in EMC, wireless communications applications, and Defense EW systems.
-
product
RF Amplifier
SA822
Hangzhou Softel Optic Co., Ltd.
SA822 860 MHz outdoor distribution amplifiers are mainly used for bidirectional trunk transmission of CATV television image signal, digital TV signal, telephone voice signals and data (or compressed data) signal.
-
product
Femtosecond Multipass Ti:sapphire Amplifier
MPA 50
MPA 50 is a multipass Ti: sapphire amplifier based on a two-mirror confocal design and containing a pulse stretcher, a pulse compressor, a pulse picker, synchronization electronics, and the Faraday isolator.
-
product
Broadband Power Amplifier
PAS-00210-80
* Solid State Power Amplifier* Small Signal Gain: 50 dB typ.* Rack Mount Case* Internal Cooling Fans* Type N Connectors* Over-voltage, over-current protections* Microprocessor controlled (optional)* Current monitor (optional)* Ethernet interface (optional)* Variable Gain (optional)* ALC power control (optional)
-
product
Variable Gain Amplifier
VGA
RF Lambda’s variable gain amplifiers (VGA) are standard amplifiers which include a gain control pin to allow the customer to tune the gain for various applications without sacrificing performance and eliminating the need to use a separate amplifier and attenuator. Hermetically Sealed options are available upon request.
-
product
CATV Booster Optical Amplifier
HA5100
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HA5100 series is a CATV booster optical amplifier with gain spectrum band within 1540~1563nm. This kind of optical amplifier is designed for the application of single channel or 1~8 continuous ribbon channels (ITU wavelength). Generally, fiber CATV system operates in single wavelength that has no strict requirement on gain flatness. HA5100 booster amplifier is featured with low NF, high-saturated output power. It is applicable for central bureau, sub-bureau and line relay, as well as other optical communication network. HA5100 is applied most commonly and widely compared with other optical amplifier in CATV system.
-
product
Switched Limiting Amplifier With Detected Output
Limiting amplifier sets dynamic range from -10.0 to -5.0 dBm input to 2.0 dBm output. TTL controlled, fast switching and high isolation 10 dB On-to-Off, and includes internal filtering for improved harmonic performance. Analog detector monitored output, or dual RF outputs.
-
product
Optical Limiting Amplifiers
Analog Devices high gain optical limiting amplifiers feature low power, low jitter, and excellent sensitivity performance. Our limiting amplifiers include receiver functions such as quantization, loss of signal detection, and SFF-8472-compliant average power measurement. Along with SFP, SFF, and GBIC MSA module designs, our amplifiers also support physical layer protocols that include 1 ×, 2 ×, and 4 × Fibre Channel, 10GBASE-LX4, multiple rate SONET/SDH up to OC-48 with FEC, and Gigabit Ethernet.
-
product
Low-noise High-voltage Amplifier For Tube-scanners -
HV200/5
The HV200/5 is a high-precision HV-amplifier designed for the control of tube scanners. It takes three input voltages In X, In Y and In Z (-10 V to + 10 V), amplifies them separately (input gain switches: x1, x2, x5, x10, x20) and adds an offset voltage between -10 V and +10 V. In a 2nd stage, the signal is amplified by a factor of 20. This enables its use as HV amplifier in scanning image acquisition applications, such as STM or AFM, with the capability to shift the scan range in high resolution imaging.
-
product
PXI Voltage Amplifier SMB Type Connector
41-650-002
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
product
Standard GaN Amplifiers
A GaN (Gallium Nitride) amplifier is a power amplifier that uses GaN, a wide-bandgap semiconductor material, to provide high power density, efficiency, and frequency capabilities.
-
product
DT Range Broadband Power Amplifiers 10 KHZ - 1000 MHZ
DT Series
Class A solid stateBroadband (instantaneous single band): 10 kHz 1000 MHzTypical output power : 25 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 20 W and H<-20 dBc up to 450 MHz andP1dB > 10 W and H<-20 dBc from 450 MHz to 1000 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Rack3 years standard warranty
-
product
High-Voltage Amplifier
ZET 420
The high-voltage signal amplifier for emission of acoustic signals through capacitive emitters: sonic detectors (without integrated amplifiers), piezoelectric emitters, and transducers.
-
product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
product
2 GHz to 6 GHz, 25 W Power Amplifier Module
HMC7748
The HMC7748 is a multistage power amplifier (PA) that provides 25 W of saturated output power across the band of 2 GHz to 6 GHz. It draws 0.7 A from a 12 V supply and up to 4 A from a 28 V supply. Input signals of as much as −8 dBm are acceptable, and the module has small signal gain of 60 dB. The 12 V supply is regulated internally and generates the negative voltage required for the gate bias. Built-in bias sequencing prevents the drain voltages for the amplifier stages from being applied without the negative voltage present, which protects the amplifiers if 28 V is applied without 12 V supply applied.
-
product
UX Range Broadband Power Amplifiers 2 GHZ - 6 GHZ
UX Series
Class A solid stateBroadband (instantaneous single band): 2 GHz 6 GHzTypical output power : 15 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 12 W and H < -20 dBc up to 4 GHz andP1dB > 11 W and H < -20 dBc from 4 GHz to 6 GHzAir cooling: self contained fansCan operate in full mismatch conditions without damageUpgradable to UX 30 possible (4U)Reliable, efficient and robust19" Rack3 years standard warranty
-
product
Third Party RF Amplifiers
We work closely with major manufacturers to supply a range of oscilloscopes, function generators and power amplifiers. We are the UK agent for the leading manufacturer of RF amplifiers Electronics and Innovation.
-
product
Distribution Amplifiers
A complete range of distribution amplifiers are manufactured by Precision Test Systems. A distribution amplifier is used to distribute the output of a frequency reference to many different places. Usually the frequency is 5 or 10 MHz but we manufacture distribution amps from DC to over 2000 MHz. We make some of the industries lowest phase noise products.
-
product
mAEStro Digital Audio Re-Clocking Distribution Amplifier
The mAEStro ADA-100 receives AES/EBU (AES3) or S/PDIF digital audio and provides four re-clocked digital audio outputs. It automatically detects sample rates from 32kHz to 96kHz with low-jitter clock recovery. The outputs are completely regenerated using a jitter-free clock that is locked to the source input. The rugged self-contained metal enclosure has a number of mounting options from desktop, to rear side-rail rack mounting, to ganged front-side or rear-side rack mounting.
-
product
Amplifiers
Computer-controlled charge amplifier module features variable gain and output scaling and accepts either differential or single-ended inputs. Adjustable parameters include: accelerometer sensitivity, differential or single-ended mode, scaling, filter setting, external calibration and zero mode.
-
product
Solid State Power Amplifiers
SSPAs
Communications & Power Industries
- Ruggedized for use in pulsed airborne, naval and ground radar- Found in weather forecasting Doppler radar systems- Utilized world-wide in air traffic control and precision approach radar systems
-
product
Composite 2×12 Video Distribution Amplifier 12VDC
VDA212RM-12
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
product
VHF Band 1.0 Watt Amplifier With RF Bypass
Teledyne RF & Microwave has developed a 35 to 350 MHz custom amplifier with 1 watt output power. The amplifier has 29 dB gain with 3 dB noise figure. The amplifier assembly has a RF switch so that the RF input can be connected directly to the output bypassing the amplifier. The amplifier goes into the "bypass" state when the DC bias is removed from the switch. This unit is one of a series of amplifiers that covers the 1 MHz to 2100 MHz with similar operation.
-
product
Logarithmic Video Amplifiers
DLVAs, ERDLVAs & SDLVAs
PMI’s Detector Logarithmic Video Amplifiers (DLVA, ERDLVA, SDLVA) are offered covering DC to 40 GHz with extended range models offering dynamic ranges over 70 dB. Our standard products provide exceptional temperature stability, log linearity and frequency response. As well, most SDLVAs provide a limited IF output. PMI offers custom DLVA’s and SDLVA’s to meet your requirements or replace obsolete products, please email your requirement to sales@pmi-rf.com so we can propose an instant solution.
-
product
RF Power Amplifiers
Specially selected products to complement our ultrasound measurement equipment.
-
product
Saluki SPA Series Solid State Power Amplifier (max. 23KW output power)
Saluki SPA series is a solid-state RF power amplifier with an output frequency of maximum 110GHz and an output power of a maximum of 23000W. Its design is based on the most advanced GaN technology in the industry, and its power output is efficient and reliable. The product has functions such as temperature and current detection, alarm protection and so on.The broadband solid state power amplifier is mainly used for testing and measuring instruments, Communication or interference, aviation control and other fields.*Customization Available*
-
product
Solid State Broadband High Power Amplifier 1900 - 6000 MHz / 200 Watts
2215
The 2215 is suitable for octave bandwidth high power CW, modulated and pulse applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak power capability and low distortions. Exceptional performance, long-term reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. for EMC, RF Product Test, Communications and Electronic Warfare applications.
