-
product
RTM Analog & Discrete Signal Conditioning Board
CPCI Rear IO Analog and Discrete Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advance Compute & IO Module (MS3663i). This board primarily focusing on signal conditioning of TTL/CMOS DIO levels to required type of discrete input and output interface. Digital IO from ACIO board to discrete IO at Rear IO interface. Board takes 144 DIO from ACIO and does Open/Ground, 28V/Open, 28V/Ground configuration. In addition it shall generate additional 32 discrete input / output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector. And Board takes 16 Analog outputs and 64 Analog inputs from ACIO and does signal conditioning. In addition it shall generate additional 40 Analog input and 32 Analog output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector
-
product
CDM Test System
1100-CDM series
Tokyo Electronics Trading Co., Ltd.
Model 1100-CDM is the latest model developed as a successor to the conventional CDM-550, and supports testing methods (Field-Induced CDM) that conform to international standards. In addition, a camera and a high-accuracy robot can apply CDM stress to a precise position.
-
product
Multi-GNSS RF Simulation System
GSS6300M
The Spirent GSS6300M is the ideal platform for entry-level and low-cost test requirements. Capable of generating signals from multiple GNSS coherently, the GSS6300M is a valuable tool in development and production test environments.
-
product
Data Acquisition Systems And Recorders
Aiming to measure, condition, process, monitor and record analogue and digital signals from all common types of physical sensors.
-
product
Cable Identification System
After excavation, sometimes it is confusing to identify the right cable from a bunch of cables. Cable Identification is very important for the safety of field personnel – Cutting a wrong cable can be fatal. So, we require a Cable Identification System to identify the wanted cable.
-
product
Intelligent Power System Recorder
iPSR
The iPSR™ is a 48 channel recorder (16 analog and 32 digital inputs) designed to intelligently record power system data. “Intelligently” does not mean compression. “Intelligently” means providing summary data allowing a quick identification of abnormalities combined with a fast download of the relevant data.
-
product
Application Specific LC Systems
Nexera MX
Higher throughput is of the utmost importance to laboratory efficiency and profitability. Nexera MX processes twice the number of samples as conventional LCMS systems in the same amount of time.
-
product
Benchtop/Portable Cable/Harness Wiring Test System
CKT1175-10
Designed for wiring testing requirements requiring up to 2,000 test points, the CKT1175-10 is ideal as a benchtop or portable test system. The system is packaged in an enclosure specifically designed to be used in rugged environments. The basic 500 test point system is 20.5 in. (521 mm) wide X 12.0 in. (305 mm) high X 16.05 in. (408 mm) deep; the 500 test point expansion units are 20.5 in. (521 mm) wide X 6.00 in. (153 mm) high X 16.05 in. (408 mm) deep.
-
product
Measurement System of Ultrasonic Vocalizations (USV)
SONOTRACK®
Sonotrack is the only recording system which is designed for laboratory use and high-throughput analysis of USV. It records the full spectrum of ultrasonic vocalizations from 15 kHz to 125 kHz without limitations for the "recording duration". The ultralow-noise amplifiers and highly sensitive microphones provide unrivalled quality of the recorded signals.
-
product
Cable Diagnosis System
Baseline 9400 TDR/ICE
K&S Engineering and Scientific Ltd
BASELINE 9400 TDR/ICE - the unique cable diagnostic system: - A state-of-the art cable fault locating instrument containing a high speed data recorder, capable of capturing and evaluating 40 million samples of electrical data per second, while also featuring amplifiers, attenuators and an adjustable pulse generator.
-
product
High Power Temperature Forcing System
MaxTC G4
NEW G4– MaxTC is our premium Temperature Forcing System product, specifically designed for industry needs as a result of customer´s feedback from the Flex-TC. Its powerful cooling force (90W @ -40°C), rapid transition rates (75°C /min) and remote control capabilities will provide solutions to all semiconductor testing needs. MaxTC is compact, ultra quiet (55 d BA) and fits into any laboratory. A premium product at amazing value.
-
product
High Speed Camera Systems
MEMRECAM
nac’s High speed camera products have an ongoing record of technical innovation and an integrated line-up that set industry standards for performance and reliability in the realm of high speed cameras. nac is the best choice for your high-speed imaging requirements.
-
product
RTM Analog Signal Conditioning Board
MS 3633I
CPCI Rear IO Analog Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on all type of Analog input and output interface including signal conditioning from ACIO board to Rear IO interface. Board takes 16 Analog outputs and 64 Analog inputs from ACIO and does signal conditioning. In addition it shall generate additional 40 Analog input and 32 Analog output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
-
product
Measurement System for ESD Protection
SampleProtect
The SampleProtect measurement system is ready to go, and comes complete with Oxford Instruments’ Cryofree bottom loading cryostat – the OptistatDry BLV, Zurich Instruments’ MFLI Lock-in Amplifier, a specially designed ESD break-out box and high quality measurement grade cables. The patent-pending puck style mounting from Oxford Instruments provides safe installation of your samples. The MFLI 500 kHz Lock-in Amplifier (capable of 500 kHz demodulation as standard) with MF-MD multi-demodulator capability brings the benefits of high performance signal processing at low and medium frequencies. The differential voltage and current inputs of the MFLI are optimised for low noise operation and the high oversampling rate ensures an even better signal to noise ratio. Zurich Instruments’ unique LabOne® control software provides a toolset including an integrated oscilloscope, a spectrum analyser, a plotter and a parameter sweeper.
-
product
Wind-Noise Reduction System
WNRS
The Wind-Noise Reduction System (WNRS) is an array of air inlets connected with pipes to reduce wind-noise and improve signal quality.
-
product
Mini Cryogen Free Systems
mCFMS
Cryogenic offers cryogen free measurement systems, which include a cryocooler, cryostat with superconducting magnet (3, 5, 7 or 9 Tesla), variable temperature sample space, a selection of special probes for measurements of different physical properties, as well as electronics, computer and measurement software.
-
-
product
Data Recorder and Playback System
Curtiss-Wright Defense Solutions
The proliferation of sensors in today’s Intelligence, Surveillance and Reconnaissance (ISR) applications has increased the need for recording and playing back multiple channels of high-speed sensor data. Often times these ISR platforms are airborne which present certain environmental requirements that must be met for the system to be flight ready.
-
product
Real Car Transient Test System
RealCar Simulation Bench
This system is suitable for transient test of actual vehicle in combination with the real-time model calculation by the measurement/control panel and low inertial motor. By replacing the wheel of the actual vehicle with the tire type bearing, the axle shaft is taken out to the outside of the vehicle and connected to the low inertia motor. It can be reproduced the sliding motion which the chassis dynamometer cannot be realized. Also, since the longitudinal force is not occurred in the vehicle, the vehicle restraint can be simplified and the behavior such as shift shock can be reproduced on the bench.
-
product
Condition Monitoring
Our condition monitoring products provide you with the essential data needed to prevent unplanned downtime before it costs you. Real-time monitoring of the health and condition of your machines enables smart manufacturing. This allows you to predict and protect against potential equipment failures before they have a chance to impact quality and maintenance costs.
-
product
Charge/Discharge System Controller
PFX2500 Series
PFX2500 Series is a high performance Charge/Discharge system controller that takes measurements in combination with our DC power supply and electronic load in order to evaluate test sample (electric storage elements such as secondary batteries) characteristics. It is also capable to perform evaluation test with high-performance, large capacity and wide range of rating with the combination of DC power supply and electronic load.Execution of the test is conducted by the exclusive application software. The test corresponds to long time continuous test and synchronization test with temperature chambers with the multiplexed protection performance. In addition, easy data editing is also capable with fulfilling graphic performance.
-
product
ARM 9 System on Module
MS 1515
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz SDRAM- Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Serial Interfaces: Up to four external UARTs- + CAN 2.0B controller- + Three I2C ports- + Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements- Mechanical: 60 mm wide x 60 mm long x 5.4 mm high
-
product
Laser Raman Microscopy System
RAMANforce/RAMANtouch
Nanophoton is the pioneer of confocal laser scanning microscopy and spectroscopic analysis. To celebrate, we relaunch our fastest and highest resolution confocal Raman microscope RAMANtouch/RAMANforce. With a newly designed spectrograph and the latest optical technologies, RAMANtouch/RAMANforce’s spatial resolution and sensitivity have been highly improved, making it the optimal solution for all applications.
-
product
Multi-Axis Hot Deformation System
MAXStrain
The system restrains specimens lengthwise while allowing unlimited deformation in the other two dimensions. As a result, very high strain levels can be introduced into specimens to produce a sample of ultrafine-grain or nanoscale material that is large enough for subsequent properties testing.
-
product
Development System
FE-51RD2
* Emulates Atmel AT89C51RD2, AT89C51ED2 and others * 60K Code Memory * Real-Time Emulation * Frequency up to 20MHz/3V, 33MHz/5V * ISP and X2 Mode Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
product
System Amplifier
SAM100
The R&S®SAM100 system amplifier is an ultra-broadband solid state microwave amplifier with a frequency range from 2 GHz to 20 GHz. With a power of up to 20 W, outstanding linearity and very good noise characteristics, the R&S®SAM100 amplifier is ideal as a compact system amplifier in various measurement setups e.g. design (DVT) and product validation test (PVT) or EMC. In measurement environments with R&S generators, frequency analyzers or network analyzers, they can act as drivers or boosters and amplify the measurement signals
-
product
Cogging Test System
CTS
Magtrol’s Cogging Test System is a stand-alone test system designed to control and measure Detent Torque, Cogging Torque and Friction Torque. The test System includes a precision geared motor, a TS Series Torque Sensor integrating a 5 000 pulses encoder. CTS 100 to CTS 102 have a built-in security clutches to avoid system overload by mishandling when not in use. The geared motor drives the MUT (Motor Under Test) at a low speed from 1 to 10 rpm (respectively 8 rpm for CTS 103 and CTS 104), while acquiring its cogging torque related to angle position.
-
product
Operation Support System for Wafer Prober
N-PAF
N-PAF (Network-Based Prober Advanced Function) is a networking system developed for more effective operation and maintenance of multiple wafer probers. Remote operation helps save on labor on the factory floor. An E10-compliant RAM Analyzer can be used for operation management of the system
-
product
Embedded Systems
Embedded systems consist of computer hardware, input and output (I/O), and software typically used for system control or monitoring applications. Our engineers are experts at integrating control system electronics with components and sensors, including motors, pumps, valves, signal transducers, and much more. We have developed and deployed thousands of systems that include industrial assembly lines, scientific instruments, medical devices, large installations like factories, manufacturing equipment, and electrical grids that rely on multiple embedded systems networked together.
-
product
Microwave Generators And Systems
MKS offers compact industrial microwave generators and systems in 915MHz and 2450MHz that are adaptable to a wide range of applications including include Food and Beverage Packaging, Environmental and Advanced Industrial processes like coating, material growth, and automotive. With a robust, modular power system chassis design and advanced filament and electromagnetic management, MKS microwave generators are engineered to last. The microwave generators are equipped with switch mode topology for all power ranges and support a variety of fieldbus communication protocols.
