-
product
GPIB to Relay Interface Boards
Model 4864 OEM
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Fully IEEE-488.2 and SCPI compliant.* Includes 50-pin mating Relay connector and serial header connector.* Optional terminal board for easy connections without soldering. See the GPIB Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel. • 114521-12 Board provides 16 heavy duty form A contacts (SPST).* All other specifications are the same as for the 114521-11 Board. * 114521-14 provides 16 Relay driver outputs that sink 300 mA.* All other specifications are the same as for the 114521-11 Board.
-
product
Interface Adapter. USB Solution
U2C-11
Dimax USB to I2C Bridge device - U2C-11 converts USB transactions to I2C Master transactions. U2C-11 turns your PC running Windows or Linux OS into comprehensive I2C Bus master.
-
product
Interface Converter
ZET 7176
Interface converter Ethernet/Wi-Fi↔CAN ZET 7176 is used for connection of CAN interface instrument communications nets based on digital transducers to PC over Wi-Fi or Ethernet. Wi-Fi or Ethernet network throughput rate allows to immediately fulfill commands and transmit great scope of data. Shared use of ZET7176 and ZET 7172 interface converters allows arranging instrument communications nets with radio linked transmission interface.
-
product
Ethernet To Modbus RTU Minibox™ Interface
ICS's Model 9099 Ethernet to Modbus RTU Interface is a small Minibox™ Ethernet Modbus Converter that converts Modbus TCP/IP, VXI-11 and Raw Socket to control Modbus RTU Slave Devices. The Model 9099 does not require special drivers and is compatible with the following systems: LINUX, UNIX, SunOS, MAC OS X, HP-UX, IBM-AIX, Windows 2K or later and Modbus capable PLCs. ICS's 9099 uses VXI-11 RPC calls for secure communication with virtually any computer. Easily programmed on a PC by making VISA calls or on a MAC/UNIX/LINUX computer with RPC calls. Special drivers are not required. ICS Electronics is the premier VXI-11 device supplier with 100% VXI-11 compliance in every product. See our extensive Application Notes or download our VXI-11 Tutorial and the VXI-11 Specification for more information about the VXI-11 Standard.
-
product
PCI 16 Isolated Input Digital Interface (3-13V)
8006
The 8006 PCI digital I/O interface provides 16 optically isolated inputs for connection to devices including sensors, switches, push buttons, and other user inputs. The inputs can sense both AC and DC voltage while providing optical isolation, which eliminates spikes and surges present in industrial environments.
-
product
Parallel Interface Voltage Output D/A Converters
Analog Devices offers a large portfolio of parallel interface voltage output D/A converters (DACs). We provide precision, fast settling, rail-to-rail micropower VOUT D/A converters, with resolutions of 8 bits up to 16 bits, single-channel to 40-channel density, and a unipolar or bipolar supply. These devices are used in a wide variety of applications such as process control, automotive test equipment, or digital gain and offset adjustment.
-
product
True Reference Audio Interface With MDIO Expansion
Titan
Titan and Atlas are world class multi-track interfaces offering flexible expansion and unsurpassable sonic clarity. Using the latest generation of Prism Sounds trusted conversion, Titan is ideal for music and sound recording, multi-tracking, overdubbing, stem-based mastering, analogue summing and critical listening applications.
-
product
MIL-STD-1553 Test & Simulation Interface for PCI Express
PCIe-C1553
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - x1 Lane PCI Express Host Interface (x4 Physical edge connector) - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Fibre Channel XMC Interface Module
XMC-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Supports DMA for high speed streaming of data to/from the board - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
Data Interfaces, Sensors And Actuators
Dewesoft also develops and manufactures data interfaces such as CAN USB devices, GNSS and INS positioning devices, and Inertial Measurement Units (IMU), and high-speed cameras. All devices are completely compatible and synchronized with all of our Data Acquisition (DAQ) systems and offer the same highest possible built quality. To complete the measurement chain we also provide high accuracy current and vibration sensors.
-
product
Virtual Interface Technology for 3D-IC Metrology
VIT
TSV profile (depth, top & bottom CD, tilt, SWA)-Residue Detection-RST-Copper Nail Height-Bump Height and Cu pillar height-Edge trim profile
-
product
SIP-90-4 Test System Interface Probe
SIP-90-4
Overall Length (mil): 693Overall Length (mm): 17.60Rec. Mounting Hole Size (mil): 57Rec. Mounting Hole Size (mm): 1.45Recommended Drill Size: 1,45 mm
-
product
HMI Operator Interface Panels
- Robust and powerful HMI for operation and monitoring- Programmable and parameterizable to IEC 61131-3 with CODESYS- Vibration and shock resistant housings with high protection rating- Units for surface or panel mounting- Powerful interfaces for various communication tasks
-
product
RS-232 to RS-485 Optically Isolated Interface Converter
Model 8322
FEATURES: 4 Wire-Master/Slave Operation; Active Mode Control Via RTS or Data; Opto Isolation; Built-in Power Supply; Internal Microcontroller; 38.4 KBPS Data Rate; DIN Rail Mountable; Programmable Terminations. The Model 8322 RS-232 to RS-485 Interface Converter allows information exchange in half duplex mode over two twisted pairs.
-
product
8 GHz Differential Probe with ProBus2 Interface
DH08-PB2
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
Isolated Serial Interface Card
PCI-ICM-2S
The PCI-ICM-2S serial communications card can be installed in five-volt PCI-bus computer slots and provides effective communication on long lines in noisy environments. Data lines are opto-isolated from the computer and from each other to assure communication even when large common mode voltages and noise are imposed.
-
product
Genrad 2270 Interface Receivers
GR Series
The 3210 Series Receiver is designed for interfacing the GR 2270 style test fixture. Using patented CAM/TRAC design, the 3210 Receiver provides an accurate, positive locking system that ensures consistent contact throughout the entire interface. With a 5/8" stroke, the 3212 Receiver allows additional clearance for coax and custom block applications.
-
product
Ethernet Bridge Converter for MIL-STD-1553 and ARINC
ENETX-MA4
eNetX-MA4™ is an innovative product for “remoting” 1553 & ARINC-429/717 operations on 10/100/1000 Ethernet local area networks (LAN). eNetX-MA4 is a very small, low-power, rugged device that provides real-time UDP connectivity to for 1-2 dual redundant 1553 (A/B) busses and 4 ARINC channels. Tested to MIL-STD-704F/810G/461F and DO160.
-
product
Software & Hardware Interface
XJAPI
The XJAPI is a simple-to-use DLL Application Program Interface (API), designed to give you low-level access to the JTAG chain via either the XJLink or the PXI hardware, allowing easy integration with a wide range of other systems such as development/evaluation boards, test systems
-
product
30 GHz differential probe with ProAxial interface
DH30-PX
30 GHz differential probe with ProAxial interface.
-
product
Real Time Monitor Interface
ANALYSIS 4N
It supports a management on the on-site equipment, such as to add subnets, to add subnet equipment, or to config equipment parameters, etc. Subnet fulfills the following applications: parallel communication, interaction with equipment, batch logging, downloading, configuration, ending, timing synchronization and system status viewing.
-
product
MVTec Interfaces
If you cannot find a suitable interface for your device, you can use a template for the integration and download it here. Simply select "Templates" in the "Category" selection field.
-
product
VME Controller With USB-2 Interface
VM-USB
The VM-USB is a VME master with high speed USB2 interface. Enhanced functionality is given by the programmable internal FPGA logic which provides a VME command sequencer with 4kB stack and 28kB data buffer. Combined with the 4 front panel I/O ports this allows VME operation and data acquisition / buffering without any PC or USB activity.
-
product
Power Interface Board 3U, 2PSU connectors with AC pins
106PIBM302-9001R
The PIB 3U 2 slot has two power connector P47 with AC pins and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
product
Human Machine Interface
Panasonic Automotive & Industrial Systems Europe GmbH
combines state-of-the-art features and top performance with an outstanding design in an all-metal housing. The range consists of four models in sizes from 4.3", 7", 10.4" and 13.4" TFT color display with LED backlight. All models can be installed in a horizontal or vertical position. The touch terminals are equipped with an Ethernet port and support VNC technology, allowing both remote VNC applications and remote assistance. The HM500 series is programmed with the HMWin software, a simple and intuitive program, yet equipped with advanced features. It is possible to import variables from Control FPWIN Pro, the programming software for Panasonic PLCs, thereby facilitating the synergy between PLCs and HMIs. The products have a 5 year warranty.
-
product
GPIB Interface Card
PI-31000
The Pulse Instruments PI-31000 IEEE Interface Card is a standard GPIB Interface card offered by National Instruments. This interface card is used in applications where the PI-2005 Pattern Generator or other instruments are controlled from a remote system CPU, or it can be used as the system controller when the CompactPCI CPU is the system computer.
-
product
Ethernet-GPIB-USB to Serial Interface
Model 9006
* All interfaces provide full communication with the serial device.* Ethernet port supports VXI-11 and raw socket protocols.* Controllable with Windows PC programs like C, Visual Basic, LabVIEW, VEE, etc that make VISA or SICL calls.* Controllable from MAC/UNIX/LINUX and similar computers with RPC calls.* GPIB port is IEEE-488.2 compatible.* USB port uses Microsoft supplied driver to prevent driver problems with operating system change problems.* Serial port provides RS-232 and 2 or 4-wire RS-485 signals.* Supports devices that generate asynchronous messages, devices that respond when queried and smart devices.* Internal webserver for easy configuration from any browser.* Board runs on 5 to 15 Vdc power.* Includes ICS's VXI-11 and VISA keyboard control programs.* Works with Agilent, NI and Kikisui VISA libraries.
-
-
product
Handler/Prober Interfaces
IFXX
FETtest offers a variety of Interface options, which expand test capability and provide connection to other production line resources. These interfaces range in complexity from simple handler/prober interfaces to interfaces with user programmable external component connections, to capacitance measurement systems. Models are available to work with the full range of FETtest systems and Remote Stations.
-
