-
product
Waterproof Dual Range Tester
TDSTestr 11
For use in water and wastewater treatment, boiler blow-down, electroplating rinse tanks, drinking water, hydroponics, printing industry, aquaculture, aquariums, fish farms, swimming pools and spas.
-
product
PARASITIC DRAW TESTER
MD649
*Provides an easy way to connect a multimeter to a vehicle's electrical system to diagnose hidden battery drain*In-line fuses protect both the meter and the tester in the event a high current source on the vehicle is left on*Tester and meter can remain connected until other computer systems shut down, isolating the drain
-
product
Circuit Tester With Buzzer
28620
Tests low voltage up to 28 volts. Spring loaded hook can be removed to use the probe tip only. Can also be used to check polarity and battery drain.
-
product
Compact Tablet Hardness Tester
HC 7
The new member of our Lab.line product family: the HC 7 hardness tester for manual use in the laboratory.Equipped with a touch display and the new database-driven touch software, the HC 7 impresses with its exceptional user-friendliness. The new software can be operated intuitively and is equipped with all important functions for quick operation.Start your quick, direct and product testing with just a few clicks directly via the touch display and set up to 50 products. Reports can be printed externally via USB or LAN interface. It is also possible to connect DYMO* and EPSON* roll printers (*special models only).
-
product
Hydrogen Portable Leak Tester
H 6000
The H 6000, a new comer in the ATEQ range of leak detectors, is one of the finest gas tracer and hydrogen leak detectors on the market today.This gas is less expensive than Helium gas. Furthermore, it's a volatile, non-toxic and nonpoisonous gas without any environmental impact.
-
product
Installation Testers
Offers two models that verify the safety of electrical installations in residential, commercial and industrial applications. Has been developed to carry out the following safety measurements of electrical installations in accordance with EN 61557 and DIN VDE 0100: Insulation resistance, RCD tests, Low Ohm resistance, Earth ground resistance, Loop impedance, Phase sequence.
-
product
Ethernet Tester
GAOTek Gigabit
GAOTek Gigabit Ethernet Tester is a handheld tester for installation, commissioning and maintenance of 10M/100M/1000M ethernet networks. By combining network performance test & monitoring, data packet sniffing, traffic generation, cable test and BER test in one unit. It is widely used in testing BER of layer 1, layer 2, layer 3, and full-featured RFC-2544 and Y.1564 testing. It can help the front-line field technicians analyze the network quality and locate the fault rapidly.
-
product
Diesel Compression Tester
34700
Measures cylinder pressure on diesels equipped cars and trucks. Records maximum pressure reached during engine test. Release valve allows for immediate venting and resets gage for repeat tests. Swivel end quick coupler is connected to adapters sold separately. High pressure hose is 16 1/2" long. Gage is scaled from 0-1,000 PSI and 0-70 BAR.
-
product
Avionics Data Bus Tester
Distributed CORVUS
Distributed CORVUS works in conjunction with CORVUS-300 to isolate bus anomalies and fault resolution. The Transmit unit, C-9235-TX, sends 1553 like data pattern through a bus stub and coupler to the Receive unit, C-9235-RX, on another stub. This will measure insertion loss, possible bit errors and correct polarity. The Receive unit can also be used to give a digital scope representation of the active data bus showing signal quality and peak to peak amplitude.
-
product
DC Hipot Tester
296
Our Model 296 is a simple-to-use Hipot Tester with the built-in ability to easily test Ground Continuity (Low Current Continuity). The 296 is capable of performing Hipot Tests in both AC & DC currents. You need a Hipot Tester that includes all the features you need to get the job done, the 296 has what you're looking for Make testing simple with common sense security settings.
-
product
Ground Leads Continuity Tester
Weshine Electric Manufacturing Co., Ltd
1. The new power supply technology is adopted in the grounding down lead conduction tester.2. It has the characteristics of small size, light weight, large output current, good repeatability, strong anti-interference ability and protection function. 3. The whole machine is controlled by single chip microcomputer, which has a high degree of automation. 4. The instrument has high precision and easy operation. The maximum current is 10A.
-
product
Multifunctional testers
MI 3155 EurotestXD
MI 3155 EurotestXD is the newest flagship of Metrel’s most advanced line of multi-functional measuring instruments and is designed specifically for testing in industry. What differentiates this instrument from the rest is its ergonomic design and an intuitive user interface, encompassing a memory organizer and fully programmable AUTO SEQUENCEs, managed through a large colour touch screen display.
-
product
Portable Winding Resistance Tester
1. Handheld winding resistance meter2. Conversion function for standard temperature resistance.3. 500 test data can be saved and download by flash disk.4. Temperature testing function.
-
product
Earth Testers
Kyoritsu Electrical Instruments Works, Ltd.
Earth Ground Testing. Most facilities have grounded electrical systems, so that in the event of a lightning strike or utility overvoltage, current will find a safe path to earth. A ground electrode provides the contact between the electrical system and the earth.
-
product
Roughness Testers
Roughness is an important parameter when trying to find out whether a surface is suitable for a certain purpose. Rough surfaces often wear out more quickly than smoother surfaces. Rougher surfaces are normally more vulnerable to corrosion and cracks, but they can also aid in adhesion. A roughness tester is used to quickly and accurately determine the surface texture or surface roughness of a material. A roughness tester shows the measured roughness depth (Rz) as well as the mean roughness value (Ra) in micrometers or microns (µm). Measuring the roughness of a surface involves applying a roughness filter. Different international standards and surface texture or surface finish specifications recommend the use of different roughness filters. For example, a Gaussian filter often is recommended in ISO standards.
-
product
Non-Contact Voltage Testers
PeakTech Prüf- und Messtechnik GmbH
User-friendly tester for non-contact voltage testing from 50 V to 1000 V AC. Suitable for outlets, lamp sockets or against wire insulation testing. If AC voltage is present at the relevant measuring point, this is indicated visually by a flashing red LED and the integrated buzzer sounds. If the measuring point is voltage-free, the test probe lights up permanently green.
-
product
Core Loss Testers
S30 and S30S Series
Stacks built with punched laminations can have a lot of quality issues. Even though the lamination material is tested in sheet format before any process, that alone is not sufficient to guarantee good quality stators. Wear and tear of the punch, bad welding, bad insulating coating in annealing add to the magnetic losses in the stator. It is always advisable to test the stator core in it's final format before winding to ensure good quality throughout the production batch.
-
product
Wire Crimp Testers
Imada offers manual and motorized wire crimp test systems in either vertical or horizontal configurations.Lever-operated systems offer basic functionality and rapid destructive testing up to 220 lbf.Motorized systems have speed control and are capable of destructive or force-controlled non-destructive testing up to 1100 lbf.Choose from manual or automatic wire-gripping fixtures.Digital gauges offer data output for analysis with data acquisition software.Create your own custom configuration or consult our application specialists.
-
product
Medical Withstand Voltage Tester
2670YM
Shenzhen Chuangxin Instruments Co., Ltd.
Medical Withstand Voltage Tester，2670Y Medical Withstand Voltage Tester Has All The Function Of The Conventional Withstand Pressure Tester,And Increasing The Arc(Flashover)Detection Function,It Can Test The "Flashover" Phenomenon Of Electrical Equipment Intuitively,Accurately,Rapidly And Reliably Through The External Oscilloscope,The Measured Electrical Equipment Without "Flashover" Phenomenon,
-
product
Variable Impact Tester
1615
The Elcometer 1615 Variable Impact Tester is a simple to use gauge ideal for evaluating the resistance of a coating to impact (elongation, cracking or peeling).
-
product
Vamp Flex Tester
UI-FT15A
Vamp Flex Tester is to determine the wet or dry flex resistance of leather and finishes applied to leather.
-
product
Pull Off Adhesion Tester
106
Applications for the Elcometer 106 Adhesion Test include paint or plasma spray on bridge decking, coatings on steel, aluminium, concrete etc.Supplied in a carry case - ideal for site testsHand operated - no need for a power supplyIncludes a cutter for EN13144 and ISO 4624 tests
-
product
Drop Weight Tear Tester
DWTT
Since the introduction of the Drop Weight Tear Tester - DWTT, materials have moved on. In particular, demands for high operating pressures of line-pipes and larger diameters have driven the development of higher strength steels. Forty years ago the work that led to the drop weight tear test was done on X52 steel (360MPa yield strength). Improvements in thermo-mechanical processing has yielded improvements of approximately 10,000psi per decade, to the point where the state of the art is now X100 steels, and the use of X120 steels is being considered.
-
product
Digital Battery Testers
Electronic devices designed to test the remaining capacity of a battery's overall charge.
-
product
Bluetooth and WLAN Testers
Bluetooth and WLAN Testers provide a full range of test capabilities for all R&D, manufacturing, and field applications.
-
product
Traction Battery Drop Tester
Guangdong Bell Experiment Equipment Co.,Ltd
Traction Battery Drop Tester Relevant standards requirementsSingle Storage Cell Safety TestDropt testing steps：Charge the single storage cellaccording to 6.1.3Drop the positive negative terminals of the cellfrom the height of 1.5m to the concrete floor；Observe for 1hBattery Module Safety TestCharge the battery module according to the standard 6.1.4Drop the positive negative terminals of the battery from the height of 1.2m to the concrete floorObserve for 1h
-
product
Audio Impedance Testers
1107 IM
Standard Electric Works Co., Ltd
● Large LCD : 68 × 34mm(2.677" × 1.338").● True measurement of speaker systems actural impedance at 1kHz.● Three test ranges allow testing of home theater and commercial sound systems.● Measures transformer impedances.● Battery operation.● Low battery indication.● Data hold function.● 0Ω adjustment.
-
product
6-48V Auto Tester
1959
Peaceful Thriving Enterprise Co Ltd
*Voltage Display: 6, 12, 24, 48V*LED indicates polarity.
-
product
CCTV Tester
M-IPC-200A
Fuzhou Metricu Technology Co Ltd
3.5 inch IP camera tester M-IPC-200A with analog, HD-TVI, HD-CVI, AHD
-
product
Resistance Tester
METRISO® 3000
Wolfgang Warmbier GmbH & Co. KG
Suitable for resistance point-to-point and resistance to ground measurementsIntegrated data logger with USB communication port for data transmission (50.000 test values). The supplied Report Generating Software ETC allows to generate a complete test reportA barcode scanner can be used in order to record measurement points before testing
