-
Product
Low-Profile High-Performance IEEE488 GPIB Interface for PCI Bus
LPCI-3488A
Interface
ADLINK LPCI-3488A GPIB controller interface card, fully compatible with the IEEE 488 instrumentation control and communication standard, is capable of controlling up to 14 stand-alone instruments via IEEE 488 cables. It is designed to meet the requirements for high performance and maximum programming portability. The built-in 2KB FIFO and a block transfer mode provide up to 1.5 MB/s GPIB transfer rate. With the APIs that are compatible with NI-488.2* and VISA support, the LPCI-3488A provides the greatest compatibility with your existing applications and instrument drivers. (* NI-488.2 mentioned here is the trademarks and properties of National Instruments Corporation.)
-
Product
PCI Analog IO Board
MS 1803
-
*Bus Interface:- PCI Bus*Analog Inputs:- 16 Single Ended Inputs / 8 Differential Ended Inputs*Input Resolution:- 16 Bits*Input Range:- ±10V*Gain:- Programmable Gain Control (1, 2, 4, 8, 16)*Sampling Rate up to 100Ks/S*Peak Measurement +ve and -ve peak for all input channels
-
Product
3U i7 Quad Core, 2.4 GHz Processor cPCI Express Controller
GX7945
Controller
The GX7945 is a single-slot embedded cPCI Express 3U controller for use with Marvin Test Solutions' PXI Express chassis. When combined with the embedded storage peripherals which are integrated into PXIe chassis, the controller / chassis offers a compact, high performance, and integrated test platfrom solution.
-
Product
PCI 32xSPST Shielded Reed Relay Card
50-125-021
Reed Relay
The 50-110/115 range of PCI shielded switching cards are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female connector.
-
Product
PCI Precision Resistor Card 3-Channel, 2.5Ω To 102kΩ
50-297-140
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Precision Resistor Card 3-Channel, 2.5Ω To 1.51MΩ
50-297-144
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Express To PCI Express Expansion With 16 PCIe X4 Gen-2 Slots
ExpressBox16-BX4
-
Magma’s ExpressBox 16 is the simplest solution to seamlessly increase the number of PCI Express® slots available to your server or workstation. ExpressBox 16 expands one host PCIe® slot to sixteen slots by extending PCI Express signals over a high-bandwidth x8 or x16 connection to an external Magma enclosure.
-
Product
PCI Data Acquisition Boards
AD14-100DMA Series - Dual 14-bit A/D, 25 MS/s
-
Model AD14-100DMA is similar to the ADDA14-100DMA, but does not have D/A converters.
-
Product
Flexible x4 PCI Express to 4 MiniPCI Express Splitter
SKU-072-0X
-
Flexible x4 PCI Express to 4 MiniPCI Express Splitter (Splitter) was designed to expand modern motherboard (ATX, mini ATX etc.) that have PCI Express interface. It allows connecting up-to four MiniPCI Express add-in expansion boards to the standard motherboard PCI Express connector.Splitter includes 4 MiniPCI Express Adapter boards, x4 PCI Express Host board and 4 Flat PCI Express Cables.
-
Product
Compact PCI PICMG 2.20 Backplanes
-
Comtel Electronics offers the Serial Mesh Backplanes PICMG 2.20 High Speed mesh connections on ZD connectors (P4 area). Fully compliancy with PICMG 2.0 Rev 3.0 Specs & 2.20 Spec.
-
Product
6U Compact PCI® Single Board Computer
CP62001
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62001 is a 6U CompactPCI® single board computer designed based on Intel® GM45 chipset, compliant with PICMG®CompactPCI® specifications. There are SATAII, USB2.0, 10/100/1000Mb Ethernet, and Keyboard/Mouse interfaces on board. The display controller integrated in CP62001supports VGA and DVI dual output independently, with up to 2048×1536 resolution on CRT. Up to 4GB soldered memory on CP62001, leaves no worry about the board stability under harsh shock and vibration environment for end users. Besides, LinkedHope™ provides variant drivers BSP) support, such as VxWorks, Linux and Windows, as reduces the workload of system integration and the development of final solutions and shorten the Time-to-Market.The CP62001 with high performance/power ratio, works stably in extended temperature range, and is an ideal selection for high reliability and high availability required applications, like harsh environment communication, network security, video/image processing and can also be an ideal control unit in variant devices and equipment.CP62001 has a ruggedized version (called CP62002)with conduction cooling and wedge-lock technology. CP62002 is designed for extremely harsh environment.
-
Product
PMC to PCI Adapters
-
The PMC to PCI, PMC to CPCI and PMC to PC/104+ adapters enable the use of the PMC650 or PMC850 bus analyzers in PCI, CompactPCI and PC/104+ systems. The PMC analyzer plugs onto the adapter and then the mated adapter and analyzer plug into a PCI, CompactPCI or PC/104+ system. These passive adapters route the bus signals from the analyzer to the bus with minimal trace length and impedance matching. The adapters provide the full 64 bit interconnect between the analyzer and the bus.
-
Product
PCI Bus Synchro - Resolver - LVDT I/O Cards
PCI Synchro
-
Computer Conversions Corporation
Proven "Whole" Std. ConvertersOptimized Thermal ManagementExternal Synchro AMP I/O100% Transformer Isolated I/OPermits 2 wire X/Y Stators(Air)No External Parts or Power RequiredReference Powered(NAVAL) Options10-16 BIT Resolution ProgrammableVirtually Indestructible Outputs1.2 to 4.5VA High Power ModelsMix/Match Input & Output TypesSimultaneous Fine/Coarse Transmit For Multispeed Outputs
-
Product
Thunderbolt 3 RazorMax Express 16-Bit Digitizers
TB3 – RazorMax
Digitizer
Thunderbolt 3 provides the largest bit-rate capacity interface possible at up to 40 Gbps (5 GB/s) over a USB-C connector to support a variety of protocols including PCI Express (PCIe).
-
Product
100 KS/s, 12-Bit, 16-Ch Universal Multifunction PCI Card
PCI-1711
-
16-ch single-ended analog inputCost-effective12-bit A/D converter, with up to 100 kHz sampling rate16 single-ended analog inputsProgrammable gain16 digital inputs and 16 digital outputs16-ch digital input and 16-ch digital outputTwo 12-bit analog output channelsOnboard FIFO memory (1,024 samples)Onboard FIFO memory (1024 samples)Automatic channel/gain scanningOnboard programmable counter
-
Product
MiniPCI Express System Timer (PCIe Interface)
SKU-032-06
-
This MiniPCIe Timer uses a PCIe interface for synchronization of IP signals. This hardware-based solution provides accurate clock timing for Asterisk® open-source PBX software.
-
Product
Circuit Module, Riser for ISMB, PCIex4 to 3 PCI A201,RoHS
AIMB-R430P-03A2E
Circuit Module
- Connecting Interface: PCIe x4- Expansion Slots: 3 x 32-bit/33 MHz PCI- PLX PEX_8111BB PCIe to PCI Bridge
-
Product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 8 Channel
50-201-008
Fault Insertion Unit
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
Product
PCI High Density Pecision Resistor Card, 6-Channel, 4Ω To 2.97MΩ
50-298-051
Programmable Resistor Module
The 50-298-051 is a high density programmable resistor card with 6 channels which can be set between 4Ω and 2.97MΩ with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
COM Express Type 10
-
The COM Express Type 10 modules are designed with all components necessary and offer the most updated bus interfaces. The COM Express modules satisfy a wide range of vertical embedded applications with features of great computing performance and rich I/O capabilities, and reduce customers' time-to-market and ownership cost.
-
Product
PCI Very High Density Multiplexer, 49-Channel, 4-Pole
50-670C-022-49/4
Multiplexer Module
The 50-670C-022-49/4 is a 49-channel, 4-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 63.7 Ohm With SPDT
50-293-111
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
64-CH Isolated Digital I/O PCI Cards
PCI-7432/7433/7434
Digital I/O Module
ADLINK's cPCI/PCI-743X series cards are 64-CH high-density digital input and/or output cards that provide a robust 2,500 V isolation protection and are suitable for most industrial applications. The wide input range of the cPCI/PCI-7432 and cPCI/PCI-7433 makes it easy to sense the status of external devices. There are several options for PCI-743X series, such as normal version with input range from 0 to 24 V, as well as HIR version with high input range from 0 to 50 V. The PCI- 7433ALC is specifically designed for AC power test system.
-
Product
PCI 32xSPDT Reed Relay Card
50-110A-021
Reed Relay
This is the 32xSPDT version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
PCI Very High Density Multiplexer, 99-Channel, 1-Pole
50-670C-021-99/1
Multiplexer Module
The 50-670C-021-99/1 is a 99-channel,1-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
Product
IRIG Time Code Receiver for Computers (PCI Express)
TCR180PEX-EL
-
Meinberg Funkuhren GmbH & Co. KG
The TCR180PEX-EL receives IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes and can be used for synchronizing the system time of its host PC. The IRIG output of this card can generate an IRIG signal for other IRIG time code readers. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements).
-
Product
2-port 10GbE PoE PCI Express Card
AX92324
-
Intel® Ethernet Controller X550-AT2, up to 10 Gbps data rate, Supports 15.5KB Jumbo Frame and IEEE 1588, Compliant with IEEE802.3at to deliver 25.5W per port, PCI Express x4 compliant, PoE power on/off via Power Manager software and API, Operating temperature range from 0°C to 55°C
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 3Ω To 52.4kΩ
50-298-133
Programmable Resistor Module
The 50-298-133 is a high density programmable resistor card with 4 channels which can be set between 3Ω and 52.4kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
5 Port PCI Express
PEX 8505
-
The ExpressLane™ PEX 8505 5-lane, 5-port switch product offers PCI Express switching capability conforming to the PCI Express Specification r1.1. This device with an equal number of lanes and ports can be used in a wide variety of applications including control planes in the communications and networking markets, embedded systems, notebook and docking stations, set-top boxes, digital video recorders and multi-function printers.
-
Product
Express Analyzer
MAYA Express
-
Lyncis Express Analyzer was developed to answer the need for fast and reliable material chemical composition analysis. The application is valued by the clients where modern agile manufacturing metrology being applied and quick assessment of material is necessary to adjust critical process parameters without waiting on the lab results.
