-
Product
Mainframe or -E Expansion Chassis - Control up to 16 Modules with up to 8 Relays per Module
LXA/128-MF
-
These Chassis control up to 16 modules with up to 8 relays per module. A large variety of different switch modules are available to build almost any configuration. Modules are available to build matrix or mux configurations or discrete relay modules. Input detection modules, output driver modules and proto board modules allow custom systems for almost any application. LEDs on the front panel show switch and power status. A thumbwheel manual control is optional.
-
Product
NI-9159, 14-Slot, Virtex-5 LX110 FPGA, MXI-Express CompactRIO Chassis
781315-01
-
14-Slot, Virtex-5 LX110 FPGA, MXI-Express CompactRIO Chassis - The NI‑9159 is a rugged MXI‑Express chassis for high-performance, high‑channel‑count applications. With the NI‑9159, you can add C Series I/O modules to your PXI system or industrial PC. You can daisy chain up to six NI‑9159 chassis in a single chain and connect up to eight chains to a single controller.
-
Product
PXI 4 Slot BRIC 60x8 2-pole (2 sub-cards)
40-561A-022-60X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI And PXIe Chassis
-
PXI chassis and PXI Express (PXIe) chassis available in 8 to 19 slots and different performance characteristics. These chassis are fully compliant with PXI standards and can house any vendor’s modules. Our Gen 3 PXIe chassis offers full hybrid capability on all peripheral slots, giving you the flexibility needed to choose whichever PXI or PXIe products best fit your applications.
-
Product
cDAQ-9188 , 8‑Slot, Ethernet CompactDAQ Chassis
782824-01
-
8‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9188 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this … chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
PXIe-1084, 18-Slot (17 Hybrid Slots), Up to 4 GB/s PXI Chassis
786397-01
-
PXIe, 18-Slot (17 Hybrid Slots), Up to 4 GB/s PXI Chassis - The PXIe-1084 features an all-hybrid backplane to meet a wide range of high-performance test and measurement application needs. It also offers a Timing and Synchronization option that includes external clock and trigger routing. The hybrid connector type in every peripheral slot enables the most flexibility in terms of instrumentation module placement.
-
Product
7-Slot LXI Modular Switching Chassis
60-102B-001
-
This 7-slot LXI chassis allows any of our large number of 3U PXI modules to be installed and controlled through a standardized Ethernet interface. Each of these modules are supported as though they are an LXI compliant device, complete with a driverless soft front panel that provides complete control of the module functions. The chassis supports up to seven 3U modules and is equivalent to an 8-slot PXI chassis.
-
Product
PCI Express® Bus to 3U PXI Express™ Chassis Expansion Kit
PCIe-PXIe-8565
-
Includes PCIe-8560 peripheral card, PXIe-8565 3U system module, and ACL-EXPRESS cable in 1, 3, or 7 meter lengthsCompliant with PXI-5 PXI Express hardware specification Rev.1.0 and PCI Express Base Specifications Rev. 1.0a250 MB/s maximum system throughput
-
Product
PXIe-1084, 18-Slot (17 Hybrid Slots), Up to 4 GB/s PXI Chassis
784058-01
-
PXIe, 18-Slot (17 Hybrid Slots), Up to 4 GB/s PXI Chassis—The PXIe-1084 features an all-hybrid backplane to meet a wide range of high-performance test and measurement application needs. The hybrid connector type in every peripheral slot enables the most flexibility in terms of instrumentation module placement.
-
Product
PXI 4 Slot BRIC 230x8 1-Pole Dual Analog Bus (5 sub-cards)
40-560A-021-230X8-M
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 4 Slot BRIC 276x8 Dual Analog Bus (6 sub-cards)
40-560A-021-276X8-M
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Chassis Remote Control Cable
-
The Chassis Remote Control Cable connects the PXI Remote Control Module to a variety of host interfaces on desktop PCs, rack-mount controllers, laptops, or other PXI or PXI Express systems.PXI Remote Control Modules support either copper cabling or fiber-optic cabling, and some models support both. Copper cables offer higher data throughput capability but are generally shorter (1 meter to 10 meters), while fiber-optic cables are available in much longer options (100 meters or more) but may have lower data throughput capability.
-
Product
3U PXIe Chassis
6025
-
The new W-IE-NE-R PXIe 6025 series provides a fully redundant and front accessible chassis solution for performance critical applications. Built as a 19” rack-mount chassis with 7U height and low depth the chassis is outfitted with an 8 slot PXIe hybrid backplane from Hartmann Electronic. A redundant power supply design as well as cooling fan tray guarantees highest reliability & availability.
-
Product
Desktop/Wallmount Chassis For MicroATX Motherboard
IPC-5122
-
Shockproof drive bay for slim ODD and 3.5" or 2.5" HDD, Lockable front door prevent unauthorized access. LED indicators for system fault detection, Easy-to-maintain system fan and reusable air filter. Built-in Intelligent System Module enabling whole system fan control and remote manageability.
-
Product
cDAQ-9181, 1‑Slot, Ethernet CompactDAQ Chassis
782052-01
-
1‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9181 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
cPCI Serial Chassis 4 Slots
4U 32HP
-
As the established PICMG 2.0 CompactPCI has evolved, so has Hartmann Electronic’s product line. The 4U cPCI 4 slot solution is designed with quality and versatility in mind. This chassis comes complete with a 3U, 4 slot PCIe Gen3 backplane with full mesh topology, powered by a 180W ATX power supply.
-
Product
Wallmount Industrial Chassis for ATX Industrial Motherboard
RK-608MB-C / IMB-M40H
-
ADLINK's rackmount and wallmount industrial chassis are aligned with integrated subsystem design, service and performance, is optimized for combined motion/vision/IO applications.
-
Product
SAE AS5643 Mil-FireWire PXI Express Test & Simulation Instrument
HSSUB-6120
-
Avionics Interface Technologies
Highest density capability available in an AS5643 3U PXI Express, single slot instrument - Four (4) FireWire nodes, each with three (3) ports - Apps provide high-level (AS5643) and low-level (1394) access, while accommodating end-user customization - S100, S200, S400, S800 transfer rates - Support all Nodes operating concurrently at 800 Mbps - Independent transformer coupling for each port - Eight (8) standard PXI backplane triggers - Industry standard Texas Instruments IEEE 1394b Chipset - ANSI C (typical), C++/C#/LabVIEW
-
Product
PXI 4 Slot BRIC 44x8 2-pole (2 sub-cards)
40-562A-022-44X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
Expansion Adapter Chassis
TB3-TO-CMC-LP
-
The TB3-TO-CMC-LP is an expansion adapter chassis using the Intel Thunderbolt 3 interface. The adapter allows the use of a front I/O XMC or PMC card outside its normal confines of a single board computer (SBC) or PC hosted carrier card. The TB3-TO-CMC-LP enables the deployment of XMC or PMC modules in systems previously unable to host them -- laptops, small form factor PCs, and other computers lacking add-in slots.
-
Product
cDAQ-9174, 4‑Slot, USB CompactDAQ Chassis
781157-01
-
4‑Slot, USB CompactDAQ Chassis - The cDAQ‑9174 is a CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9174 also has four 32‑bit general-purpose counters/timers. With multiple timing engines, you can run seven hardware-timed operations simultaneously, with three independent rates for analog input.
-
Product
cDAQ-9178, 8‑Slot, USB CompactDAQ Chassis
781156-01
-
8‑Slot, USB CompactDAQ Chassis - The cDAQ‑9178 is a CompactDAQ USB chassis designed for small, portable sensor measurement systems. The chassis provides the plug‑and‑play simplicity of USB to sensor and electrical measurements. It also controls the timing, synchronization, and data … transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The cDAQ‑9178 also has four 32‑bit general-purpose counters/timers. You can access these counters, as well as share clocks and triggers, through two built-in BNC connectors.
-
Product
Chassis - Control up to 16 Modules with as Many as 32 Two Pole Relays Per Module Allowing 1xN Multiplexers up to 1020x1, 2 Pole Muxes up to 512x1 or 2xN Matrix Configurations up to 256x2
JX/256-MF
-
These Chassis control up to 16 modules with as many as 32 two pole relays per module allowing 1xN multiplexers up to 1020x1, 2 pole muxes up to 512x1 or 2xN matrix configurations up to 256x2. Jumpering option allow the modules to be controlled as separate smaller muxes, i.e. 64 4x1 2 pole muxes, or combine specific groups to allow an almost unlimited combination of sizes. Add a Control Module and optional manual control to complete the system.
-
Product
PXI 8 Slot BRIC 300x8 2-pole (10 sub-cards)
40-561A-122-300X8
-
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
NI-9154, 8-Slot, Virtex-5 LX50 FPGA, MXI-Express CompactRIO Chassis
782457-01
-
8-Slot, Virtex-5 LX50 FPGA, MXI-Express CompactRIO Chassis - The NI‑9154 is a rugged MXI‑Express chassis for high-performance, high‑channel‑count applications. With the NI‑9154, you can add C Series I/O modules to your PXI system or industrial PC. You can daisy chain up to six NI‑9154 chassis in a single chain and connect up to eight chains to a single controller.
-
Product
3U CompactPCI 6-Slot Cubic Chassis with CompactPCI Power Module
cPCIS-2500 Series
-
The cPCIS-2500 series 3U CompactPCI 6-slot Cubic Chassis is designed for 3U CompactPCI cards and modules without rear I/O. It is 4U in height, 237 mm deep, and suitable for bench top use or wall mounting. It is ideal for industrial or transport applications where small chassis size and versatility are important. A built in cooling system with removable filter provides maximum cooling efficiency, and the 250W cPCI power supply allows easy maintenance. The cPCIS-2500 series' ability to handle a wide range of temperatures and excellent shock and vibration characteristics make it suitable for operating in a rigorous environment.
-
Product
Chassis - up to Twelve 8x1 or 4x2 Modules & up to Six 8k Modules
HXV/96-MF
-
These Chassis controls up to 12 8x1 modules, 12 4x2 modules, or up to 6 of the 8K modules in almost any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules, Driver Modules and a Control Module to complete the system.
-
Product
AXIe High-Performance 5-Slot Chassis
M9506A
-
5-slot AXIe chassis with embedded system module, Gen 3 performance, 300W per slot, and GPS option.
-
Product
4U Rackmount Chassis
-
4U rackmount chassis is a cost-effective computer chassis featuring a complete line of backplanes, power and storage device options. The 4U computer chassis provide the best support for various wallmount and rackmount system.
-
Product
2-Slot BRIC, 256x4, 1Pole, PXI Matrix (2 Sub-cards)
40-559-201-256x4
-
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays. With their high level of switching density, these PXI matrices allow a complete Functional ATE system to be housed in a single 3U PXI chassis and allow the use of much lower cost 8 or 14-slot chassis. The 40-559 matrices can be used in many industries; typical applications include automotive ECU and semiconductor package testing. Dual analog busing for the narrower matrix options, enable completely separate matrices within a single module for parallel testing.
