-
product
PXI High Density MUX BRIC, 32-Chan, 10-Pole
40-570-412
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
PXI High Voltage Multiplexer, 12-Channel
40-320A-001
The 40-320A-001 is a single 12-channel MUX and is part of our 40-310/320A range of High Voltage Switching Modules which will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320A) configurations.
-
product
PXI Dual 8 to 1 RF MUX MCX 75 Ohm
40-834-102
The 40-834-102 is a 75 Ohm 8 to 1 RF MUX with 2 banks in a single PXI slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40-834 minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
product
PXI Dual SPDT RF Switch 6GHz 50 SMA Terminated
40-880-001
A range of 50Ω SPDT RF switching with automatic termination of unused signals. Available as a dual switch in a 1 slot PXI module, a quad switch in a two slot PXI module or hex and octal switches in three slot PXI modules.
-
product
LXI Microwave Multiplexer, 50Ω 6-Channel 2-Bank 26.5GHz SMA
60-801-302
The 60-801-302 is a 6-channel, 2-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
PXI 8 Slot BRIC 110x4 2A 2-Pole Matrix
40-566A-102
These modules are 2 Amp high-density large PXI matrix modules with the ability to switch up to 2 Amps at 150VDC/100VAC. They are available in 4 or 8-slot PXI sizes and are constructed using quality electro-mechanical relays for high switching confidence.
-
product
PXI BRIC4 FIBO Matrix Dual 20x4 3pin brkout
40-592A-001
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
PXI/PXIe Microwave Multiplexer, Triple SP6T, 3GHz, 50Ω, N-Type, Remote Mount
40-785C-563-E
The 40-785C-563-E (PXI) and 42-785C-563-E (PXIe) are triple SP6T 3GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
product
PXI Dual Microwave Transfer Switch 26.5GHz 50 SMA
40-782A-532
The 40-782A-532 is a dual transfer switch and is part of our range of PXI microwave switching modules. It has a characteristic impedance of 50Ω and a maximum operating frequency of 26.5GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
product
LXI Dual 8:1 Optic MUX SC/PC SingleMode
60-850-212
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
-
product
Single 16 to 1 50 600MHz PXI RF Multiplexer
40-764-001
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
product
PXI 8 Slot BRIC 360x8 2-pole (12 sub-cards)
40-561A-122-360X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
COM Express Basic Size Type 6 Module with 12th Gen Intel® Core™ Processor (formerly codename: Alder Lake-P)
Express-ADP
ADLINK’s Express-ADP COM Express Type 6 Basic size module is based on the 12th Gen Intel® Core™ processor and is the first COM Express module to support advanced hybrid architecture with up to 6 Performance-cores (P-cores) for IoT workloads and up to 8 Efficient-cores (E-cores) for background task management, boosting productivity and fueling IoT innovation across a wide variety of deployments.
-
product
Multiplexed Measurement Unit
YAV90MMU
YAV90MMU module (Multiplexed Measurement Unit) is a powerful subsystem containing 16-channel multiplexer and a 600V data acquisition channel with capability to control external switching and it is expandable through CAN bus.
-
product
PXI/PXIe Microwave Multiplexer, Single SP4T, 18GHz, 50Ω, SMA, Terminated
40-785C-421-T
The 40-785C-421-T (PXI) and 42-785C-421-T (PXIe) are single SP4T 18GHz microwave multiplexers with automatic termination of unused signals. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
product
400 MHz to 4.4 GHz, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device
783151-01
400 MHz to 4.4 GHz, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device - The USRP-2952 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless communication systems. Built on the LabVIEW reconfigurable I/O (RIO) architecture, USRP RIO delivers an integrated hardware and software solution, so researchers can prototype faster and shorten time to results. You can prototype a range of advanced research applications that include multiple input, multiple output (MIMO); synchronization of heterogeneous networks; LTE relaying; RF compressive sampling; spectrum sensing; cognitive radio; beamforming; and direction finding. The USRP-2952 is equipped with a GPS-disciplined 10 MHz oven-controlled crystal oscillator (OCXO) reference clock. GPS disciplining delivers improved frequency accuracy and synchronization capabilities.
-
product
NI-9472, 24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module
783907-01
24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module - The NI‑9472 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 30 V, … features transient overvoltage protection between the output channels and the backplane, and has an LED that indicates the status.
-
product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Dual Channel
40-204-002
The 40-204-002 (PXI) and 42-204-002 (PXIe) are dual channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault. Using the fault bus, switches can simulate a short between both wires or a short to one of two externally applied fault conditions – such as battery supply or ground - via two fault buses.
-
product
Zynq Ultrascale+ MPSoC (ZU19/17/11EG) 3U-VPX Plug-in Module
iW-RainboW-G35V®
AMD Xilinx’s ZU19/17/11EG Zynq Ultrascale+ MPSoC64bit, 8GB PS DDR4 RAM with ECC (Upgradable)Dual 64 bit, 8GB PL DDR4 RAM (Upgradable)8GB eMMC Flash (Upgradable)3U VPX Connectors based on ANSI/VITA 46.30 (P0+P1A & P1B+P2A)8 Optical transceivers through MT Ferrule Connector (P2B) based on VITA66.4
-
product
PXI 8-slot BRIC Matrix, 96x16, 1 pole (3 Sub-cards)
40-558-801-96x16
The 40-558-801-96x16 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
8-Slot BRIC, 768x4, 1 Pole, PXI Matrix (6 Sub-cards)
40-559-801-768x4
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXI 8-slot BRIC Matrix, 256x8, 1 pole (4 Sub-cards)
40-558-801-256x8
The 40-558-801-256x8 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXI 8 Slot BRIC 184x4 1-Pole (2 sub-cards)
40-560A-121-184X4
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 26.5GHz, 50Ω, SMA, Remote Mount
40-784B-132-E
The 40-784B-132-E (PXI) and 42-784B-132-E (PXIe) are dual SP4T 26.5GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
product
PXI/PXIe High Density 2A Multiplexer, 1-Bank, 128-Channel, 1-Pole
42-614D-015
The 40-614D-015 (PXI) and 42-614D-015 (PXIe) 1-bank, 128-channel, 1-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
65 GHz Single Channel Optical Module
N1030A
The N1030A is a plug-in module for the DCA-X mainframe that can be configured with one 65 GHz optical channel, or one 65 GHz optical and one 95 GHz electrical channel.
-
product
SMARC Short Size Module, Intel® Atom® X7000 Series (Amston Lake) Processors
LEC-ASL
The ADLINK LEC-ASL is a SMARC module that supports 2/4/8 cores Intel® Atom® x7000RE (x7211RE, x7213RE, x7433RE, x7835RE) and x7000C (x7203C, x7405C, x7809C) Processors (formerly Amston Lake) with integrated Intel® UHD graphics and high-speed interfaces. LEC-ASL modules support up 16GB LPDDR5 memory, up to 256GB eMMC storage (build option) and are also available with rugged operating temperature range and low power envelope, making them a perfect match for mission critical fanless edge computing applications that run 24/7.
-
product
PXI/PXIe Microwave Multiplexer, Triple SP4T, 18GHz, 50Ω, SMA, Remote Mount
40-784B-123-E
The 40-784B-123-E (PXI) and 42-784B-123-E (PXIe) are triple SP4T 18GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
product
PCI High Density Matrix, Single 22x8 1-Pole
The 50-510A series of matrix cards feature a wide range of switching configurations (22x4, dual 20x4, 22x8 and 44x4). Larger matrices may be constructed by daisy chaining the common signals from multiple cards. Expansion cables are available for the 50-512 and 50-513: The 50-512 can be expanded to 44x8 or the 50-513 can be expanded to 88x4 using two cards linked by the ribbon cable assembly 50-976-020-0.1M. Also the 50-512 can be expanded to 22x16 or the 50-513 can be expanded to 44x8 using two cards linked by the ribbon cable assembly 50-976-050-0.1M.
-
product
PXI/PXIe Very High Density Multiplexer, 5-Channel, 32-Pole
42-675B-002-5/32
The 40-675B-002-5/32 (PXI) and the 42-675B-002-5/32 (PXIe) are 5-channel, 32-pole multiplexers and are part of our range of very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems.
