-
Product
High-Temperature Strain Gages
ZWH-, ZWN-, & ZWP-Series
-
ZWH-, ZWN-, and ZWP-Series strain gages are designed for dynamic and limited static strain measurement at hightemperature.These strain gages are manufactured using a round wire for superior bonding ability and performance. A high-fatigue wire (Option Z) is also available on each of the gages. These gages are supplied with a fiberglassreinforced tape carrier which holds the grid and leads in place during installation and are bonded using ceramic cements or Rokide® flame spray. The shelf-life of thesegages is 9 months.
-
Product
Digital Megohmmeter
800
-
The ACL 800 Digital Megohmmeter is a dependable and easy-to-use audit kit that is designed to test static dissipative surfaces for electrical resistivity and resistance according to industry standards such as ANSI/ESD test methods S4.1, S7.1, and ASTM D257. Tests are easy to perform with or without the 5lb probes. Use optional concentric ring probe for conformance to STM11.11.
-
Product
Laboratory Air Data Test Sets
-
DMA is a leading manufacturer of Air Data Test Set models for laboratory use achieving the highest accuracy and resolution. The MPS46 is digitally controlled through a keyboard, it uses very high accuracy pressure sensors, with a special characterisation for maximum accuracy (for static channel < 2 feet at sea level). Pressure resolution of 0.2 Pa. is also achievable. The intuitive user interface with touchscreen display ensures that all the functions are controlled with a minimum of key presses . The ADTS can be used in avionics ATE systems (rack height only 2U) for automated pitot-static testing through RS232, USB, Ethernet or GPIB/IEEE488. An internal pump or external rack mounted pump unit can be supplied as an option.
-
Product
Bench Power Supply, Single, Adjustable, 2 Output, 1 V, 15 V, 60 A
72-7655
-
High current switch mode power supply with remote sensing and control.*Bright 3 digit dual LED displays*Simultaneous display of output voltage and current*Excellent load and line regulation*Low ripple and noise*Overload (constant current limiting), short circuit, over temperature and OVP protections*Variable speed thermal static control fan for cooling*Highly efficient active power factor corrector*Front panel banana jacks for loads up to 5A*Rear panel binding posts for loads up to 60A*12-month limited warranty *view Terms & Conditions for details
-
Product
Low-Cost 16-Bit Multi-Function DAQ Card with 2-CH Encoder Input
PCI-9221
Data Storage
The ADLINK PCI-9221 is a 16-bit high-resolution and low-cost multi-function DAQ card, with 16-CH singleended or 8-CH differential input capable of up to 250 kS/s sampling rate. In addition, the PCI-9221 comes with a 2-CH 16-bit static analog output and programmable function I/O. The software-programmable function I/O supports a variety of applications, including TTL digital I/O, general-purpose timer/counter, encoder input, and PWM output. The flexible function I/O makes the PCI-9221 the best single-board solution for combined data acquisition and simple motion control functionalities. Ideal for manufacturing, laboratory research, and factory automation, the PCI-9221 comes with all the functions you need at an affordable price.
-
Product
Static Field Meter
-
This contactless precise electrostatic field meter can immediately sensor the static voltage on a charged body without contact. The measuring range is 0.010kV ~ 20.000kV with the sensing distance 1 inch (2.54cm). The meter provides alarm function for prompt.
-
Product
Single Phase Reference Standard Meter
-
Signals & Systems India Private Limited
The Single Phase Portable Reference Standard (SPRS-1102) from SANDS is a portable meter test equipment that helps to calibrate the error present in the single-phase energy meter i.e. the meter under test (MUT). The SPRS supports both static and electro-mechanical types of meters. It can also be used to compute the voltage, current, energy, phase angle etc of the meter under test. It has an LCD display and an alphanumeric keypad to suit the user. It can be interfaced with the PC for analysis. It has the capability of storing 1000 test results.
-
Product
Universal Testing Systems
-
Instron universal testing systems are versatile, high-accuracy platforms (available in electromechanical and hydraulic variants) designed to perform a wide range of static mechanical tests, such as tension, compression, bend, peel, shear, puncture, and more, on virtually any material. They support force capacities from fractions of a newton up to thousands of kilonewtons, with precision load measurement, high data acquisition rates, and compatibility with thousands of accessories, including a wide range of extensometers, grips, fixturing, and automation solutions to meet demanding quality and throughput standards.
-
Product
Environmental Chambers
3119-600 Series
-
The Instron environmental chambers are precision thermal enclosures designed to integrate with static or dynamic test systems, enabling evaluation of material behavior under controlled non-ambient conditions. They circulate hot or cold air over specimens and grips using forced-convection to maintain stable temperatures. These chambers are available in a variety of standard sizes (or can be customized), and are compatible with extensometers, grips, and fixtures to provide a turnkey solution for temperature-dependent testing from subzero to elevated conditions.
-
Product
Circuit Breaker Analyzer
CBA 2000
-
CBA 2000 diagnostic system is designed to grant the highest accuracy while testing circuit breaker. It can perform static and dynamic contact resistance measurement and it’s a precise timing speed and motion analyzer. Circuit breaker timing test set CBA 2000 is the perfect solution when a complete and reliable diagnostics has to be performed on circuit breakers.
-
Product
Mechatronics
-
MERA performs design, construction, supply, installation and certification of stands for various testing types:● static loading● dynamic and life-cycle● transporting testing (vibration table)● thermal testing● centrifuges● modeling of take-off, landing modes, etc.
-
Product
Pressure Gas Leak Detectors
-
The testo 512 differential pressure meter is available as four models. This model has a measuring range from 0.0.29 psi and is ideal for measuring pressure differences at filters and for carrying out pitot static tube measurements in air ducts at air flow speeds between 16 and 180 fps.
-
Product
Electrostatic Potential Monitoring Device
-
electrostatic potential monitoring device that has an interface for connecting our potential sensors EMS-01 / EMS-01A / KS-2100 and measures static electricity in real time. It is possible to monitor static electricity with simple The compatible potential sensor EMS-01 / EMS . With SD card support, measurement data and alarm history can be collected with a time stamp. Operation using the touch panel display and screen display, and to notify and manage the measurement status with multiple control outputs. ...-01A Has Passed The Intrinsically Safe Explosion-Proof Structure Certification In Combination With The Safety Cage KS-301A, And Can Be Used In A Dangerous Atmosphere.
-
Product
Motor Drive Analyzer, 1 GHz, 8 Ch, 12 bits, 10 GS/s, 50 Mpts/Ch
MDA 8108HD
Analyzer
Static power analysis - like a dedicated power analyzer.Dynamic power analysis – capture more information.Complete test coverage – control system, power section, motor.Comprehensive mechanical interface.Harmonics calculation option.Vector display option (THREEPHASEVECTOR).Waveform Transformations option (THREEPHASEdq0).16 Channels with OscilloSYNC™.
-
Product
32 Channel Multi-Purpose DIOS/TAP Modules/Interfaces for Spare JT 2148 QuadPOD Transceiver Slot
JT 2149/MPV eMPV
Interface
The JT 2149/MPV and the JT 2149/eMPV are a 32 channel multi purpose DIOS/TAP pod modules/interfaces that can be plugged into any spare JT 2148 QuadPOD transceiver slot. The DIOS channels of these units I/O interface pods enable increased fault coverage and thus improved diagnostic resolution during boundary-scan testing. The principal difference between the two versions is the use of an extended case on the eMPV that allows standard 0.1″ connections to be used to access ths TAP and static IO signals (see tab below)- on the standard /MPV unit these signals are available at the front face 0.05″ connector. The units are fully supported by JTAG Technologies’ development tools. Additional DIOS modules can be serially connected if more parallel access points are required.
-
Product
Universal Measuring Device For Magnetic Fields
Teslameter M-Test MK4
-
The M-Test MK4 precisely detects and measures static or dynamic magnetic fields. The ~ 1 mm thick tangential probe allows precise, punctual measurements in hard-to-reach places, air gaps or on surfaces. The M-Test MK4 is particularly suitable for measuring permanent magnets or small ferromagnetic parts.
-
Product
Four-Wheel Drive Dingle Roller Dynanometer for Cars with Axle Load of up to 2.4T, for Installation in an Existing LPS 3000 Dynanometer
MSR 500/2 CAR 4WD (LPS 3000) | VP 230038
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.The MSR 500/2 CAR 4WD is suitable for installation in an existing LPS 3000 base.
-
Product
Engine Speed Control and Measurement (Test Set A)
MS 1100
-
*Checks the parameters such as current, voltage, speed, and turbine gas temperature of 804E and 811 engines Portable instrument*Testing of Automatic engine control system and after burner control system*Simulates the temperature signal derived from the engine TGT (Temperature Gas Turbine) thermocouples*Simulates the speed signal, NL (low pressure shaft speed signal) drive from the L.P shaft Probe*Indicates the current signal to the FCU solenoid derived from the engine control amplifier*Measure the TGT and NL simulated signal at static position*Measure the signal produced by the engine TGT thermocouples*Measure the NL signal produced by the LP shaft*Measure the NH (High-pressure shaft speed) signal produced by HP shaft*Indicates the solenoid current, produced by the engine control amplifier*Indicates the solenoid voltage, produced by the engine control amplifier*Used to test engine in both static and dynamic states
-
Product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD (ADD. BRAKE) | VP 230041
-
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of the tyre is the same as on the road. Operating methods such as load simulation, including optional modules for the measurement of external data, e.g. driving cycles, are possible.The MSR 500/2 CAR 4WD can also be extended with a 3rd or 4th eddy current brake.
-
Product
Charge Meter
NK-1001A/NK-1002A
-
Probe-type charge meter that can easily measure the amount of discharge charge that causes static electricity destruction in the manufacturing, inspection, and assembly processes of electronic devices.Many ESD phenomena that impair electronic devices are represented by the CDM ( Device Charging Model). The CDM is a model that represents a phenomenon in which a high peak current flows at high speed when the device itself is charged and its external electrode is grounded. The coulomb meter measures the amount of discharge charge, which is the integral value of the current, with high accuracy.
-
Product
Non Contact Flange Torque Transducer
FF425
-
Contactless Torque Transducers with flange couplings at either end with measuring ranges from 0-100Nm up to 30kNm as standard (bespoke sensors up to 16MNm) for a variety of in line static and rotary torque measurement applications.The Datum Electronics Series FF425 non contact flange torque sensor and FF410 torque sensors have been designed to fit easily inline with any drive train or test rig using standard DIN size couplings. With Flange couplings at either end of the torque transducer, it has many advantages over other torque measurement systems on the market.
-
Product
Bi-Directional Differential-TTL I/O PXI Card
GX5642
Instrument Card
The GX5642 is a 3U PXI instrument card that can be used for general data acquisition, process control, Automatic Test Equipment (ATE), Functional Test, and factory automation applications. The GX5642 consists of 64 bi-directional TTL-to-differential LVDS I/O channels. Each channel has two ports (TTL and LVDS) and can be individually set to operate in either conversion or static I/O modes.
-
Product
Pitot Tubes
-
The dpm-i Pitot Tube is a new design concept in Pitot Static Tube technology. It is a multi-functional sensor. It can replace thermally heated instruments, where power requirements are high. Gives easy access to duct measurement compared to a standard Pitot Tube. For example, in ceilings voids and confined areas, where there is a thick lagging or metal cladding.
-
Product
Electrostatic Sensor
EF-S1
-
Panasonic Industrial Devices Sales Company of America
The EF-S1 Electrostatic Sensor allows for easier in-line measurement of static electricity.
-
Product
High-Density Precision SMU (10 PA, 30 V)
PZ2131A
Source Measure Unit
The Keysight PZ2131A is a high-channel density precision source / measure unit (SMU) having 5 channels per module and saving space for a wide range of applications requiring numerous precision power supplies. The narrow-pulse function and fast Digitizer Mode allow the PZ2131A to expand the conventional static DC measurements to emerging dynamic measurements. Its seamless current measurement ranging function eliminates the time it takes to change the range and expands the dynamic range to cover multiple measurement ranges, which reduces test duration. These capabilities make the PZ2131A suitable for applications that require numerous precision power supplies, such as semiconductor reliability tests and integrated circuit (IC) tests. The Keysight PX0107A low noise filter adapter lowers its voltage source noise level, which makes the PZ2131A suitable for noise-sensitive applications such as quantum computing as well.
-
Product
Acoustic Compound Protection System
ACOMPRIS
-
Static kind of infrastructure is often vulnerable to attacks by either small arms fire (SAF) or mortars. The objects could be for instance a military forward operating base, an embassy or a post from the United Nations. As attacks may occur all the time, persistent and affordable protection is required. Especially when inhibited by civilians, ease of operations use and maintenance become more important. Often installed in remote places far away from the electricity grid, power consumption is an issue.
-
Product
Liquid Level Temperature Integrated Transmitter
HR8500
-
HighReach Measuring & Controlling System Co.,Ltd
The HR8500 intelligent liquid level temperature transmitter is a meter for static pressure level measurement and medium temperature measurement. The input structure is all stainless steel sealed.
-
Product
In-line Plastic Mixers
-
Ideal for one-use fluid dispensing, Nordson EFD’s disposable static mixers eliminate the need to worry about premature curing of materials.
-
Product
LED Tester For Ultra High Power
-
Electrical Testing: Forward：VF、DVF、VFD、IF、DIF Reverse：VZ、DVZ、IR、DIR AC：VAC、IAC、WAC、PFOptical Testing: can test LOP in cd/mcd/W/mW/lm... from different optical components Wavelength λp,λd,λc,hw,purity,(x,y),CCT,CRIFour-wire measurement and contact resistance in case of deviation. Auto polarity identification and preheat function.Compatible mechanical interface.Optional ESD static test system.
-
Product
TESTVAC KIT
MVTKIT
-
*Allows fast, efficient static testing and monitoring of many vacuum operated components*Diagnostic: vacuum leaks, valve timing, engine condition*Under hood: distributors, carburetors, EFI, EGR and PCV valves
