Inertial Measurement Units
combinations of precision gyroscopes, accelerometers, magnetometers, and pressure sensors measuring motion.
See Also: IMU
-
Product
Inertial Navigation Systems
-
Safran Federal Systems is now one of the only companies with a full complement of PNT technologies with the addition of proven inertial navigation solutions.Hemispherical Resonator Gyro (HRG) Crystal™ technology leverages state of the art manufacturing and offers revolutionary performance and reliability over existing technologies, for tactical to strategic applications across all domains. With more than 30,000 HRGs produced and over 15 million operational hours, the technology is proven and tested in military applications worldwide.
-
Product
Resistance Measurement
-
Precision resistance measurement equipment for a range of applications. Specialist units measure down to fractions of a micro-ohm with high accuracy.
-
Product
Proving Units
-
Designed to suit a range of applications in the electrical contracting power utilities and industrial engineering sectors Seaward proving units are both self-powered and self-testing avoiding the need for a known supply point or bulky test equipment.
-
Product
Activity Detection Unit
DG009-M1
-
Many advanced EW receivers, particularly those associated with ECM jamming systems, do not require the high resolution frequency information associated with a DFD or IFM based receiver. This is typically the case where a single pulse present within a broad frequency band is required to be detected and instantaneously down-converted to an IF band.TDS manufactures a range of Frequency Activity Detectors (FADs) also known as Activity Detection Units (ADU) which perform frequency measurement of an RF pulse and output data in as little as 15ns. The basis of these products is TDS’s ability to produce high performance broadband channelisers and integrated detectors. These devices are ideal for receivers which must operate in very high pulse density environments.
-
Product
Measuring Stations
-
The main application is the measurement of the flux density on the surface of multipole magnets or components with magnets. A large amount of measuring stations is built for rotors.
-
Product
Measuring System
K-5201MA
-
To solve this problem, the following composition of the complex was chosen in the test stand conditions:laptop in a protected version PanasonicTBCF-53;measuring block - NIUSB-4431 with a set of vibroaccelerometers AP-2037;vibration excitation system LW 139.151-30 with mounting kit for the disk.The software of the complex provides the following functions:spectral analysis of vibration signals in the regulated range;search for natural excitation frequencies in given frequency ranges;Formation of database of existing disks;generation of reporting forms;and etc.
-
Product
Accurate Measurements
SA500
-
The SA500 is a derivative of PFOs WS500 WorkStation. Its application focuses on spectral attenuation and is designed to produce accurate measurements quickly and with confidence
-
Product
1RU Automated Switch Unit
UC1
-
Universal Switching Corporation
The UC1 switch system provides a modular solution for a variety of signals up to 50GHz, and is designed for smaller requirements. This product delivers ultra-high signal performance coupled with advanced remote/manual control and monitoring with 10/100 LXI certified Ethernet port, multi-serial port, front panel control, direct alarm input port, and auto-sense (on some PUC's).
-
Product
Environmental Measurements
-
Thermometers, temperature probes air velocity meters are everything you need for controlling and monitoring the quality of the environment, intended both as the working and as the living place.
-
Product
Calibration Units
-
Optical Stroboscope and Tachometer European Calibrator Unit was originally designed for in-house test and calibration of our comprehensive range of Digital Optical Tachometers, Optical Speed sensing products and Stroboscopes.
-
Product
PXI-4130, ±20 V, ±2 A DC, 40 W PXI Source Measure Unit
779647-31
Programmable Power Supply
±20 V, ±2 A DC, 40 W PXI Source Measure Unit - The PXI‑4130 is a programmable source measure unit (SMU). It has a single isolated SMU channel that offers a four-quadrant output that incorporates remote (4‑wire) sense. With its five current ranges, it is ideal for transistor characterization that requires accurately sourcing a constant current or voltage while sweeping another current. The PXI‑4130 also includes a utility channel that can source either current or voltage. This PXI SMU can act as either a constant voltage source or a constant current source, with a settable compliance limit for either mode. In addition, you can enable remote sense on the SMU channel to maximize voltage output and measurement accuracy on your device under test (DUT) for high-precision applications.
-
Product
Test & Measuring
-
Messung Electrical Engineering
Electronics manufacturing, testing and quality control need test and measuring equipment and ergonomic environments that are flexible, versatile and safe. Hence we bring the future of modern workplace systems for R&D labs, calibration centres, training and didactic centres, electronic assembly & testing, spread across the Indian electronic industry. Our innovative, modular & customised laboratory furniture systems, and intelligent test & measurement solutions are designed to improve efficiency while offering user comfort.
-
Product
Dual Function Slot MOSA Data Concentrator Unit (DCU)
NIU2A-DCU-01
Data Concentrator Unit
NIU2A-DCU-01 is a Modular Open Systems Approach (MOSA) Data Concentrator Unit with low power high performance ARM Cortex -A9 processing. 512 MB RAM, 32 GB SATA Flash, 2 x 10/100/1000Base-T Ethernet and optional Fiber Optic Ethernet support
-
Product
Power Supply Unit
PS-18V-U
-
Panasonic Industrial Devices Sales Company of America
A Portable Power Supply Unit available from Panasonic.
-
Product
Infrasound Measurements
-
Is sound that is lower in frequency than 20 Hz (hertz) or cycles per second, the "normal" limit of human hearing. Hearing becomes gradually less sensitive as frequency decreases, so for humans to perceive infrasound, the sound pressure must be sufficiently high. The ear is the primary organ for sensing infrasound, but at higher intensities it is possible to feel infrasound vibrations in various parts of the body.
-
Product
Measuring Management
-
Our test equipment is more than a test-set with a screen. Our application software provides an integrated tool to easily store the measurements at different stages and create a log of what we have done. Each measurement stores all data and settings, including display, markers and calibration.
-
Product
Safety Control Unit
SF-C21 Series
-
Panasonic Industrial Devices Sales Company of America
The safety control unit allows the user to connect and control various machine safety components. The SF-C10 series was specifically designed to connect and control Panasonic light curtains, while the SF-C21 safety control unit can be used for a variety of safety devices such as; safety switches, emergency switches, enable grip switches, safety beam sensors, safety scanners, and safety light curtains.
-
Product
Data Acquisition Unit CATCH
MS 1523
-
CATCH is a web based locomotive monitoring system. This system provides locomotive data on Internet. Locomotive data are automatically download and organized at one place. The downloaded data can be viewed from anywhere through the Internet. By this flexibility the decision taking authority can get into an action immediately.
-
Product
Control Unit for SITEx & SITExs
SITEX SCU286
-
The SCU286 has a system for direct measurement of the high voltage delivered by the X-Ray generator to guarantee the accuracy of the radiological parameters. Based on this data the control system maintains the stability of mA and kilovolts to within ± 0.5% in any selection range.SITEX & XS units offer a totally constant quality of exposures, as they are virtually exempt from fluctuations in the power supply.
-
Product
Inertial Navigation Systems (INS and IMU)
-
Inertial Navigation Systems (INS and IMU)High accuracy 100Hz GPS and GNSS receivers and Inertial Navigation Systems (IMU - inertial measurement units) with Real-time Kinematics (RTK) correction for the most precise position-based test and measurement applications.
-
Product
Test And Measurement
-
Standardized instruments used to evaluate individuals, populations, or processes.
-
Product
Battery Extra Load Units
-
Performing capacity/discharge test on a high-capacity battery may be challenging since high requirements are set on the discharge system. In cases when discharge test times need to be reduced, high load capacities are required from the discharge system. The battery extra load unit BXL is an additional load unit designed especially for this purpose.It is primarily used with BLU battery testers. However, the unit is a universal add-on device. This means it can be used as an additional load with any other discharge/capacity tester in the market.When discharge current exceeds the capacity of a single BLU device, extra load unit increases discharge capacity. A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way in accordance to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.
-
Product
Inline Measurement
-
X-Rite's inline solutions increase efficiency, reduce waste, and make life easier for production operators and quality controllers. It's a continuous monitoring system that can catch even small deviations immediately, so changes can be made before production moves out of tolerance. X-Rite offers inline solutions for all stages of paper manufacturing, as well as for the coil coating, plastics, coated glass, textile, and automotive industries. Inline systems are turn-key and have a very quick ROI.
-
Product
Light Measurement
-
Light is produced from many natural and artificial sources. Controlling light and having an accurate understanding of its output, directionality and the appearance of what it irradiates is key to product development, quality and the success of a light source. Here are just a few examples of why Labsphere is leading the industry in light measurement.
-
Product
PXI Based Multifunction Measurement and ICT Instrument
PXI-501
Multifunction Switch/Measure Unit
The PXI-501 is a multifunction measurement instrument for functional and in-circuit measurements.It combines two parametric measurement units with a digital voltmeter, a high voltage current source and a discharge unit. This powerful combination makes it the ideal instrument for classical analog in-circuit test and manufacturing defect analysis with additional functional test capabilities.With it’s fast sampling rate of up to 4MSps it speeds up measurements and is capable of measuring and generating AC signals up to 100kHz.To enhance the PXI-501 capabilities it can be combined with an ABex TM-501 or an ABex TM-404. The ABex TM-501 enhances the in and output range of the PXI-501. Furthermore, it provides a shunt current measurement upgrade. In combination with the ABex TM-404 it’s a complete in-circuit test solution with 86 channels in one ABex slot. For sure it can be upgraded to 2838 test points in one rack by simply adding additional matrix modules.With the above-mentioned terminal modules, the PXI-501 is able to act as a ABex system controller, so that no additional controller is required in the cassis.
-
Product
Test & Measurement
-
High-quality connection solutions for precise measuring, testing and examination. Whether low or medium voltage range, whether precise test runs or preventive measuring and testing: With an extensive portfolio of specific components and cables, Stäubli always ensures perfect and reliable contact between the measuring instrument and the points, objects and systems to be tested. In addition, we are a proven partner of leading manufacturers of measuring instruments in this field, for example for equipping them with high-quality sockets. Every product meets all quality and safety standards.
-
Product
PXI Single Bus 32-Ch 2A Fault Insertion Switch
40-190B-201
Fault Insertion Unit
The Single Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Level Measurement
Level Measurement
-
AMETEK Sensors, Test & Calibration
B/W Controls uses the same advanced magnetostrictive technology as in Gemco products providing high accuracy and reliability for continuous liquid level measurement.
-
Product
UFL Measurement
-
Many of the well known VNA manufacturors offer very expensive calibration kits and special phase-stable cables (which costs almost as much a MegiQ VNA) for measuring impedances. This is useful for some special scientific measurements, or when working in the higher GHz, but a setup with an uncooperative cable and a bulky (N) connector is not suited for measuring the small devices that we are developing.
-
Product
Measuring Tools
-
A very useful tool for various types of applications in construction and industries and a very convenient to that gives accurate measurement of distance, area and volume especially in large areas such as rooms, apartments, buildings, real estates, factories, warehouses, gardens, roads, infrastructures, and many other applications requiring accurate results for distance , area and volume measurement.
