Crimp Force
See Also: Force, Compression, Pull Force, Pull off Force, Push Pull Force, Peeling, Tension, Gravity, Electrical, Magnetic
-
Product
Mechanical Force Gauges
-
Imada mechanical force gauges are highly accurate instruments used to test the quality, strength or functionality of component parts or products. Imada mechanical force gauges check both compression and tension (push or pull). Peak force can be captured using the peak indicator needle and the tare ring compensates for the weight of attachments. Imada force gauges are constructed with a heavy-duty metal case and all metal components to enable them to retain their calibration for years with proper care. These mechanical force gauges never need charging or batteries and are intrinsically safe in hazardous environments.
-
Product
Charge Amplifier for Outputs from Piezoelectric- or mV-type Accelerometers, Force Gauges, Microphones & Pressure Pickups
Trig-Tek™ 201AP
Amplifier
Amplify the outputs from piezoelectric- or mV-type accelerometers, force gauges, microphones, and pressure pickups
-
Product
160-Pin DIN41612 Connector, Crimp Pin, Female, 45º
40-960-160-F5
DIN41612 Female Connector
Suitable for users to create their own cable assemblies where a 45 degree down cable exit would be preferred. If the user requires the connector to have a second fixing then it can be fitted with an additional screwlock assembly 40-969-101 where applications permit.
-
Product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, 22-28 AWG, Crimp, 30µ" Au
610138216
Signal Contact (Receiver)
*Please note: The difference between this p/n and 610138116 is the amount of gold plating. See below.P/n 610138116- 50µ" AuP/n 610138216- 30µ" AuPrimary mating contact 610138109. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BeCuContact Plating 30µ" Au over 100µ" NiContact Termination CrimpCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force(lbs) 0.24
-
Product
Economical Load and Force Measurement
ELF
-
Tekscan's ELF force and load measurement system matches the market's need for an inexpensive load and force measurement system with Tekscan's ability to deliver innovative load and force measurement solutions. The system consists of data acquisition hardware, software, and FlexiForce B201 sensors.
-
Product
Force Tensiometers
Sigma 700/701
-
The outstanding versatility of Sigma 700 and 701 force tensiometers makes them suitable for research and development, industrial quality control, routine measurements as well as academic research. Both instruments are computer controlled and have a high level of automation.
-
Product
Ergonomics Force Gauges
Series E
-
Series E push / pull force gauges make job task analysis and ergonomics analysis simple and accurate, ideal for workplace design, strength assessment, and ergonomic studies. Series E presents the ergonomist and other professionals with a simple and economical testing solution. 100 lbF, 200 lbF and 500 lbF (500, 2,500, and 5,000 N) capacity force gauges are available, along with a wide range of attachments for various applications.
-
Product
Axial Force And Torsion Testing Machine
-
Evaluation Testing That Approximates Operating Conditions of Materials and Parts - Loading methods similar to actual usage - Allows simultaneous application of axial and torsional loads to samples
-
Product
Force Sensors
-
General purpose force sensors are offered in either stud or axial mounted configurations. They are internally pre-loaded and can be used for dynamic compression, tension, and impact force measurements. Tapped mounting holes on both ends of the radial connector style support link, platform, integrated link, and free-standing installations. The axial mounted type offers protection of the electrical connector and sensor cable from potential damage during drop testing and in free-standing installations. Supplied impact caps facilitate impact and drop force measurements.
-
Product
Atomic Force Microscope
DriveAFM
-
The DriveAFM is Nanosurf’s novel flagship AFM platform: a tip-scanning atomic force microscope (AFM) that combines, for the first time, several capabilities in one instrument to enable novel measurements in materials and life sciences.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type I, Ø1.26mm, 155gf
K100-I126155-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style I, Tip Diameter Ø1.26mm, Spring force 155gf, Steel with Gold Plating.
-
Product
Motorized Force & Torque Measurement Test Stands
-
Mark-10 offers a wide and unique range of motorized force measurement and torque measurement test stands. Motorized stands offer a significant advantage over manual test stands by providing constant test speed. Some models can be programmed for advanced test sequences to accommodate demanding applications. All motorized test stands carry the CE mark. A test stand is an integral part of a testing system, typically also comprising a force gauge or torque gauge, grips, software, and accessories.
-
Product
Signal/ Micro Power/Micro Coax, Module, Receiver, QuadraPaddle, iCon Series, 100/15 Positions, for crimp contacts
510160107
Receiver Module
Primary mating module 510161107. (May mate with other ITA modules, as well.)
-
Product
Force Sensors
-
HBK Force Sensors and Force Transducers with strain gauge or piezo technology measure static and dynamic tensile and compressive loads up to 20 MN - with virtually no displacement.
-
Product
Temperature Forcing System
-
Wewon Environmental Chambers Co, Ltd.
Wewon Technology specializes in the research, development, production and sales of laboratory testing equipment system services. Through more than ten years of accumulation in the field of equipment, the business of wewon Tech is mainly divided into three fields, namely optical communication, automobile and new energy industry.Specialized equipment from Wewon Environmental Chambers Co., Ltd. includes thermal stream instrument, environmental chambers, walk in chamber, salt fog test chamber, vibration testing machine, xenon lamp aging tester, ultraviolet weather testing equipment, tensile testing machine and various IP protection level test equipment. The system characteristic of Wewon Tech thermal stream temperature test system as below technical parameters mentioned.https://www.wewontech.com/temperature-forcing-system/
-
Product
High Force Large Area Bond Tester
Sigma HF
-
- For high force and large area- Typically for IGBT, power modules and batteries up to 1000 kgf- High axis speed- Deep access up to 80 mm- SEMI S2 safety cabinet with visual feedback- Flexible positioning of multiple work holders
-
Product
Force Sensors For Pull/push Direction
-
INELTA Sensorsysteme GmbH & Co. KG
The force sensors can be integrated easily and uncomplicatedly by the regular standard thread.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type H, Ø0.80mm, 155gf
K100-H080155-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style H, Tip Diameter Ø0.80mm, Spring force 155gf, Steel with Gold Plating.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type K, Ø1.50mm, 230gf
K100-K150230-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style K, Tip Diameter Ø1.50mm, Spring force 230gf, Steel with Gold Plating.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type Q, Ø0.80mm, 155gf
K100-Q080155-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style Q, Tip Diameter Ø0.80mm, Spring force 155gf, Steel with Gold Plating.
-
Product
Force Data Acquisition Software
-
SW-1X data acquisition software is for force gauges with RS-232 output.SW-2X data acquisition software is for collecting force and displacement data from RS-232 output force gauges, with a -s test stand.Force Recorder data acquisition software is for ZTS & ZTA force gauges with USB output. Force Recorder Pro collects both force and displacement data with ZTA gauge and FA test stand.
-
Product
Ergonomic Force Gauges
-
AMETEK Sensors, Test & Calibration
The ergonomic gauges from Chatillon are ideal for functional capacity evaluations and basic muscle strength measurements where economy and ease-of-use are essential. Simplicity is a key design criterion for these ergonomic gauges.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type K, Ø1.50mm, 155gf
K100-K150155-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style K, Tip Diameter Ø1.50mm, Spring force 155gf, Steel with Gold Plating.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type L, Ø1.50mm, 230gf
K100-L150230-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style L, Tip Diameter Ø1.50mm, Spring force 230gf, Steel with Gold Plating.
-
Product
Force Distance Tester
925
-
The Model 925 is a low cost force-distance tester. It communicates with a Windows™-based PC to send data into an Excel format. The data can then be viewed and analyzed in tabular or graphical format. Once in the Excel format, the data can be transferred or used in any of the multiple Excel operations. This line of displacement-force test stations has a positional resolution of 0.0025 mm (0.0001 inches). Your test department will appreciate the high accuracy readings provided over the complete travel range.
-
Product
Force Transducers
-
Metra Mess- und Frequenztechnik in Radebeul e.K.
Piezoelectric force transducers are suited for the measurement of tensile and compression force.
-
Product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type D, Ø0.80mm, 305gf
K100-D080305-SKAU
Spring Probe
K100 Series, Pitch 100mil, Tip Style D, Tip Diameter Ø0.80mm, Spring force 305gf, Steel with Gold Plating.
-
Product
Miniature Quartz Force Sensors
-
Often the test engineer will try to take low level measurements with a sensors not rated for these low levels. Due to insufficient sensitivity the resulting data may be noisy, hard to analyze or unusable. Using the appropriately sized and ranged PCB Miniature Quartz Force Sensor solves the problem and gives reliable data at a Low Amplitude level. The miniature sensor configuration permits low-amplitude, dynamic compression, tension, and impact force measurements.
-
Product
Load Cells, Weighing and Force Sensors
-
We are pleased to offer Load Cells from both Zemic and Vishay. We are the exclusive UK distributor for Zemic load cells.
-
Product
AFM Atomic Force Microscope
FM-Nanoview 6800
-
Zhengzhou Nanbei Instrument Equipment Co. Ltd
All-in-one design, smart structure and shape.Scan head and sample stage are designed together, strong anti-vibration performance .Precision laser detection and probe alignment device make laser adjustment simple and easy.Adapt servomotor to drive the sample approaching tip manually or automatically, to realize precision scanning area positioning.
