Crimp Force
See Also: Force, Compression, Pull Force, Pull off Force, Push Pull Force, Peeling, Tension, Gravity, Electrical, Magnetic
-
product
Signal, Contact, Receiver, TriPaddle, 7 Amp, 20-24 AWG, Crimp only
610110101
Primary mating contact 610110108. (May mate with other ITA contacts, as well.)p/n 610110125 TriPaddle Receiver 50µ" AU plating.p/n 610110101 TriPaddle Receiver 30µ" AU plating.Specifications Operating Voltage & Current 7 Amps Max. Continuous (20 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAContact Body BeCuContact Plating 30µ” Au over 100µ” NiContact Termination CrimpCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
product
Connector, D-Type 50-Pin Male With Crimp Pins
GT96108
Connector, D-type 50-pin male with solder pins.
-
product
Force gauge management software
CNR LOCK
CENTOR Manager is a simple, user-friendly utility that enables you to communicate with your CENTOR Easy, Star or Dual memory.It enables you to:– modify the calibration date,– reset the overload counter to zero if the sensor has not been damaged,– block access to the menus and configuration.
-
product
Ergonomic Force Gauges
MSE100 Series
AMETEK Sensors, Test & Calibration
The MSE100 ergonomic gauge is a simple-to-use, ergonomically designed mechanical instrument ideal for muscle strength evaluations and job task analysis.
-
product
AFM (Atomic Force Microscope) Optical Platform
The AFM platform allows fully-integrated use of confocal Raman microscopy and AFM for Tip-Enhanced Optical Spectroscopies (such as Tip-Enhanced Raman Spectroscopy (TERS) and Tip-Enhanced PhotoLuminescence (TEPL)), but also for truly co-localized AFM-Raman measurements.The myriad of AFM (Atomic Force Microscope) techniques that allow study of topographical, electrical and mechanical properties can be performed with any laser source available in Raman spectrometer, or with other external illumination (e.g., solar simulator or other tunable or continuum source). TERS and TEPL can provide nanoscale chemical and structural information, making the AFM-Raman platform a two-way road; where complimentary techniques provide novel and unique imaging capabilities to each other.
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type C, Ø1.50mm, 305gf
K100-C150305-SKAU
K100 Series, Pitch 100mil, Tip Style C, Tip Diameter Ø1.50mm, Spring force 305gf, Steel with Gold Plating.
-
product
High Force Type Probe For PCB, K100 Series 100mil Pitch, Type A, Ø0.80mm, 305gf
K100-A080305-SKAU
K100 Series, Pitch 100mil, Tip Style A, Tip Diameter Ø0.80mm, Spring force 305gf, Steel with Gold Plating.
-
product
Force Sensor Elements
The STL Force Sensing Tension Links are a series of unique force sensors. The Tension Links utilize the internal strain gage process sucessfully and are used in bolts, load pins and flat load cells. The sensing element consists of a strain gage bridge circuit internally installed in a small hole along the longitudinal axis. This unique arrangement provides a most effective means for the protective sealing of the internal electronics while minimizing the adverse effects of extraneous torsion and bending loads.
