Friction
See Also: Abrasion
-
Product
Universal Friction & Wear Testing Machine
Model MMW-1A
-
Jinan Testing Equipment IE Corporation
The MMW-1A UTM for Friction Wear can simulate rolling, sliding and rolling & sliding combined movement under the certain contact pressure to complete point, line and plane simulating tests. The UTM for Friction Wear can be used to evaluate the friction wear performance of lubricant, metal, plastics, coating, rubber, and ceramics etc. The UTM for Friction Wear can not only satisfy the needs of traditional petrochemical industry to research, develop and inspect the various kinds of intermediate & high grade hydraulic oil, combustion engine oil and gear oil, but also can simulate evaluation on new material development and new technology research under dry condition.
-
Product
Static Friction Coefficient Tester
JMY-16
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.4-2008; Inspection standard: JB/T4279.16-2008Used to detect static friction coefficient (μs) of enameled round wires with nominal conductor diameter ranging from 0.050mm to 1.600mm;The application of high-end SCM control allows for high sensitivity and excellent repeatability.Four-digit LED would automatically display static friction coefficient (μs) of sample;
-
Product
Coefficient of Friction Gauges
M5-2-COF
-
The M5-2-COF coefficient of friction (COF) gauge is an integral part of a COF testing system, typically including a motorized test stand and COF fixture. With a capacity of 2 lbF [10 N], the gauge can be used to measure friction for a wide range of materials, ideal for conformance to ASTM D1894 and other relevant standards. Static and kinetic coefficients are displayed on the backlit LCD, and are calculated from a user-programmable sled weight.
-
Product
Inclined Surface Coefficient Of Friction
DRK138
-
Shandong Drick Instruments Co., Ltd.
DRK138 Inclined Surface Coefficient Of Friction Tester is applied to testing the COF of film, paper, card board, sheet and so on. By testing the material’s frictional properties, the open performance of packages, packaging speed of packers and other indexes could be controlled to meet the requirements for production
-
Product
Rotational Friction Torque
-
Tests the smoothness of rotation and components of small precision motors, such as, gearbox, bearings, oil seals, etc. The motorized tester turns at a set rotational speed based upon the model. See the specifications table for more details. The tester can be used to measure torque in CW and CCW directions.
-
Product
Conventional friction and wear tester
EFM-III
-
The measurement unit of A&D's conventional friction and wear tester has been adjusted to enable the measurement of friction characteristics with higher precision.
-
Product
Friction and Wear Tester
EFM-III Series
-
The EFM-III series is a friction and wear tester for tribology evaluation in conformity with JIS K 7218. This tester is designed for scientific elucidation and technical evaluation of the characteristics relating to sliding friction, wear and lubrication, that are surface behaviors of relative properties of two interacting material surfaces (relative properties of solid materials in relative motion).
-
Product
High-pressure environmental friction and wear tester
-
This testing machine is used to evaluate the frictional characteristics in a pressure container. It can evaluate the frictional characteristics of refrigerants, oil, friction materials, etc. for compressors and so on. It has a load cell inside the pressure container to enable frictional-force measurement with high accuracy.
-
Product
High Resolution Encoders
HR-E
-
The High Resolution 8-dial Encoder (HR-E) from Badger Meter uses a non-contact field-proven light emitting diode technology to provide a high resolution 8-digit reading while at the same time eliminating friction and wear of traditional mechanical encoders. The HR-E communicates using the industry standard ASCII communication protocol to provide high resolution encoded output.
-
Product
Pin-disc Friction & Wear Testing Machine
WPD-2000
-
Jinan Testing Equipment IE Corporation
WPD-2000 is one type of pin-disc friction wear testing machine. The specimen of metal and non-metal material will be matched to pin shape, disc shape or dual rings to do the test. The pin-disc friction wear testing machine can measure the anti-wear characteristics and frictional coefficient even under lubrication status. WPD-2000 Pin-disc Friction Wear Tester is available in two moods, PC & software mood or non PC mood.
-
Product
Smart Card Reader
UTC-P06
-
Card Acceptor/ Reliability: User card Friction Type (ID-1) , 200,000 cycles. OS Support: Windows XP/7/8/10, Android, Linux. Dimensions: 130 x 35 x 40 mm.
-
Product
Vertical Dual Display Spring Torsion Testing Machine
Model TNS-S-L Series
-
Jinan Testing Equipment IE Corporation
This series of testing machines is mainly applicable for testing the torsion angle and torque of various kinds of small-sized torsion springs, coil springs, elastic components and other friction structures.
-
Product
Coefficient Of Friction Testers
-
Saicheng coefficient of friction (COF) tester is specialized in measuring the static and kinetic coefficients of friction of plastic film and sheet, rubber, paper, cardboard, woven bag, fabric style, metal material composite belt for communication cable and optical cable, conveyor belt, wood, coating, brake pad, wiper, shoe material, tire and other materials when sliding.
-
Product
Friction & Wear Testing Machine
-
Jinan Scientific Test Technology Co. LTD.
Friction & Wear Testing Machine
-
Product
Space Flight Components
-
A tec, Inc. specializes in the design, manufacture, and integration of complex test systems and quality critical components. Our production engineering expertise separates us from other manufacturing companies when both reliability and cost are important. Atec has the best in 5 to 9 Axis CNC machining, coordinate measuring machines (CMMs), 3D additive metal and plastic printers, 9-Axis capable waterjet, cryogenic liquid flow test benches and environmental test chambers. We can deliver to the tightest tolerances and most exacting requirements. We can advise our customers on electron beam welding, friction joining, electronic test, environmental test, acoustics, vibration and many other technologies that can reduce manufacturing and operating costs. We are currently manufacturing liquid rocket engine fuel and oxidizer valves for multiple launch vehicles and have participated in 158 consecutive launch successes. Atec manufactured and tested advanced lithium-ion battery adapter plates that manage power for the International Space Station. Atec is designing, manufacturing, and testing power flow modules that work to prevent system failure on the human crew capsule (CCTS) that will transport astronauts to/from the ISS. Atec was awarded NASA Agency-Level Small Business Subcontractor of the Year , SBA Region VI Subcontractor of the Year for our support to NASA and Boeing and we were named a DCMA Top 500 Supplier.
-
Product
Wind Direction Sensor
ENVIROMUX-EWDS
-
Balanced wind direction vane with a near-zero friction bearing and a high accuracy magnetic angle sensor to provide precision wind direction. Sensor range: full 360 degrees , zero deadband. Accuracy: ±1.8 degrees. Resolution: 12 bit or 0.025 degrees. Directional Vane approximately 8 inches (203 millimeters). 3 wire flying leads, 25-feet (7.6-meter). Supply voltage: 4.5 to 5.5 VDC. Current: 15 mA typical. Output: 5 to 95% of input voltage (0.25 to 4.75VDC). Requires the ENVIROMUX-S5VDC-5V to operate with ENVIROMUX-2D/5D/16D. Maximum cable length: 1000 ft (305m)
-
Product
Paper Testing Instruments
-
Whiteness and chromaciticity tester, whiteness meter, tensile stiffness tester, automatic horizontal tensile tester, automatic horizontal tensile tester, vertical tensile tester, pulp beating (refining) freeness tester, water absorbtion tester, Cobb tester, COBB sample cutter, coefficient of friction tester, electronic bending stiffness tester, paper and cardboard thickness meter, paper and cardboard thickness meter, ink rubber tester, standard strip cutter, softness tester, carton compression tester, paper air permeability tester, internal ply bond tester, puncture strength tester, paper tearing tester, electronic tearing tester, mullen burst tester, crush tester, Bekk smoothness tester, folding endurance tester
-
Product
Air Actuators
-
Del-Tron's linear air actuators (also referred to as linear actuators) are pneumatically actuated crossed roller slide assemblies controlled by a pair of Airpot air cylinders which provide extremely low friction and stiction characteristics. A light touch or physical obstruction will stop the unit’s movement to prevent damage to delicate and expensive equipment and parts. Low pressure operation is possible. The PNRE series requires less than 10 psi to operate.
-
Product
High Precision Motorized Rotation Stages
RAK
-
Model: RAKHigh Precision Motorized Rotation StagesNew construction ,new technology;the key index has up to the international level of the similar products by strictly inspection .This series products are used to laser precision processing,three dimensional scanning measurment system and so on .◆Stepper motor drive ,finish angle adjustment automatically;◆Worm and worm wheel has adopted durable to friction material ,high reliable accuracy of rotation .◆High precision ,ultra steel axises of importing ,achieve high precision, high load stable motion◆Outer circle has scale, interface , convenience for signal’s output◆Circle grating and encoder combine with MC series controller ,achieve closed-loop control Standard stepper motor and DB9 interface, choose to controller flexibility◆three phase stepper motor and servo-motor is planning
-
Product
Suspension Component Test Systems
-
Acoustic quality, vehicle dynamics and stability, and driver comfort play an increasingly important role in the development of new chassis and suspension systems – both passive and active. Noises in suspension components can cause customer dissatisfaction and lead to high warranty costs and are difficult to diagnose especially on historically-used, noisy hydraulic test rigs. The MB Suspension Component Test Rig (SCTR) enables dynamic simulation of real road excitations and synthesized waveforms, performing industry-standard Force-Velocity and Force-Displacement tests and low speed friction tests, and assessing other NVH and structure-borne noises for comprehensive performance characterization and sound and vibration analyses on a wide variety of chassis components.
-
Product
Diamond-Like Carbon: High-Performance Coatings for Extreme Applications
-
When durability matters, Diamond-Like Carbon (DLC) coatings deliver. Known for their hardness, low friction, and chemical resistance, DLC films are the go-to solution for protecting surfaces in high-stress environments: from precision mechanical parts to advanced semiconductor devices.
-
Product
Full Extension Quick Disconnect Slides for 30"D Cabinets
IMS-85-C-19
-
Special order only. Friction slide yellow zinc steel slides. Ideal for mounting chassis into cabinets.
-
Product
Production Test Stands for Electric Motors
-
Electric drives such as DC and EC motors are more and more extensively deployed in the automotive industry. At the same time there is an increasing requirement for a 100% analysis of motors for fault detection and error analysis as well as statistics on quality, without increasing production cycles times. The model-based Parameter Identification method (PI method) from imc allows testing to be performed under load, yet without an “explicit” separate load machine. Instead, the motor is loaded dynamically by exploiting its own inherent inertia. This allows motor parameters such as resistance, inductivity and friction to be determined within a few seconds. A mathematical model and its parameters reflect motor behaviour in its completeness and make it possible to monitor motor production based on limit values and trend statistics. The identified parameters of the model equation can then be used to calculate derived key performance indicators of the motor characteristic curve.
-
Product
Mechanical Tester
-
NANOVEA Mechanical Tester is the most versatile nanoindenter and scratch tester capable of precisely measuring the micro- to nanomechanical properties of wide ranges of materials from thin films, coatings, ceramics and composites to polymers and bio materials via Indentation, Scratch and Friction testing. All NANOVEA Mechanical Tester models come with true feedback load control from independent load and depth sensors that provide unmatched accuracy and the highest repeatability available on the market. This technology allows a user to perform Nanoindentation and Microindentation for Hardness and Elastic Modulus Testing, Stress vs Strain Analysis, Creep and Relaxation, Loss and Storage Modulus, Yield Strength and Fatigue, Fracture Toughness and Nano-scratch & Micro-scratch for Scratch Hardness Testing, Multi-pass Wear Test, Cohesive and Adhesive Failure Testing as well as Coefficient of Friction testing, all available on one system.
-
Product
Diaphragm Operated Pressure Switch
SA1100
-
Extremely rugged construction assures excellent reliability in chemical, petroleum and industrial plants. New design also provides burst pressure protection to 3000 psi (206 bar). The rolling diaphragm design maintains a constant effective area to minimize friction.
-
Product
BUTT SHEAR
STAG 98AL
-
It needs a lubrication able to ensure an optimal lubricating and protective power in conditions of high temperature and friction.
-
Product
CMP Tester
CP-6
-
The state of the art Rtec CMP tester CP-6 allows to study and characterize CMP process like never before. In addition to polishing wafers & substrates the tester comes with inline surface profilometer. This combinations sheds information on why and how the surface, friction, wear etc. changed. Tester also measures several inline parameters such as friction, surface roughness, wear volume etc. to understand the process in detail.
-
Product
High Speed Caged Ball
SBK
-
High Speed Caged Ball Ball Screw. THK high speed caged ball ball screw type SBK that eliminates collisions and friction between ball and prolongs the effectiveness of grease by utilizing the caged ball mechanism. This mechanism reduces a noise level, torque fluctuation, and a long maintenance-free period.
-
Product
Brakes
-
Power off, fail safe holding brakes. When voltage is applied, the friction disk is released allowing the motor shaft to rotate. Pittman power off brakes are best suited for parking brake applications used to hold a load in position, and are ideal for creating brake motor packages for small frame servo and stepper motors.
-
Product
Motor Performance Tester
CT Series
-
Shanghai Aoboor Electric Co., Ltd.
Test the cogging torque of motors, separate motor cogging torque and friction torque accurately; cogging torque test results is independent of test speed and speed fluctuation.
