Fading Simulation
test to verify wireless communicatons link in adverse transmission conditions.
-
Product
Multiprotocol P104Plus Interface Board for Embedded Applications or Avionics Test & Simulation Applications
EXC-4000P104plus
-
The EXC-4000P104plus is a multiprotocol P104plus interface board for embedded applications or avionics test and simulation applications. Each board holds up to five independent modules. Two on-board modules use the MIL-STD-1553 communications protocol (M4K1553Px); another on-board module uses the ARINC-429 communications protocol; two additional detachable modules can be any one of the following types:M4K1553PxS (Single Function - RT validated) This module operates as a Bus Controller, Remote Terminal or a Bus Monitor. This module qualifies for airborne applications.M4K1553Px (Multi Function) This module operates as a Bus Controller, up to 32 Remote Terminals and as a Bus Monitor. Supports an Internal Concurrent Monitor in RT and BC/RT modes.M4K1553Px(S)-1760 Same as M4K1553Px(S) plus MIL-STD-1760 options.M4KMMSI Mini Munitions Store Interface module. Supports RT, BC/Concurrent-RT/Concurrent Monitor and Bus Monitor modes. Up to 8 hub ports EBR-1553 [10 Mbps 1553 protocol using RS-485 transceivers] and 1 monitor output.M4KH009 Based on our H009 family. This module operates as a Central Computer Complex (CCC) and/or up to 16 Peripheral Units (PUs) simultaneously, or as a Bus Monitor. In addition, a Concurrent Bus Monitor enables concurrent monitoring of the bus during CCC and PU simulation.M4K429RTx Based on our ARINC 429RxTx board. This module supports either five or ten ARINC 429 channels each of which can be configured in real time as a receive or transmit channel.M4K708 This module supports two channels of ARINC 708/453, each one selectable as either transmit or receive.M4KSerial This module supports up to 4 independent channels of serial communications, each of which can be selected as RS485, RS422 or RS232.M4KDiscrete This module supports 20 selectable input/open collector output discretes. The module supports TTL (0 to 5 volts) or avionics (0 to 32 volts) voltage levels.M4KCAN This module supports up to 6 independent channels of CAN 2.0B protocol with standard and extended message frames and message identifiers.
-
Product
2 PRI + 24 BRI-U ISDN Simulator
CH-24BRI-U-MOD-2PRI
-
The most inexpensive ISDN simulator on the market. This unit has two PRI ports and 24 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
Product
PXI Analog Output/Current Loop Simulator Module - 8 Channel
41-765-003
-
The 41/43-765-003 is an 8-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Radar Threat and Target Simulation Unit
MS 1605
-
PTG is used to field/LAB evaluation / testing of RADAR. PC is used to control the profile of the target generation. PTG will work in both stand alone and remote mode. The PTG has keypad and LCD for stand-alone operation. The PC can interface the PTG through the USB link. The operator can communicate through the GUI to the PTG. MIL1553B Communication used for Interfacing with RADAR.
-
Product
Manikins for realistic simulation of the acoustic properties of a human
Head & Torso Simulators
-
If you need to carry out realistic in-situ measurements of headphones, telephones or hearing aids, you need a Head and Torso Simulator such as the B&K ‘HATS’ – Type 4128D or GRAS’ Kemar to complete your test setup. These manikins have built-in ear and mouth simulators that provide a realistic reproduction of the acoustic properties of an average adult human head and torso. They are commonly used for tests on telephone handsets, headsets, audio conference devices, microphones, headphones, hearing aids and hearing protectors. Please contact your sales engineer or email sales@listeninc.com for more information.
-
Product
Simulators
SAE J1708/J1587
-
The Au SAE J1708/J1587 simulators (Gen II, V1.00A release) can simulate up to 44 most frequently used Engine/Transmission/ABS parameters, warnings and diagnostic messages. Up to six Engine MID, three transmission MID and six ABS MID can be field configured. All editions can run independently (without personal computer). This family of simulators are designed very easy to use. It is widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration to product development and product validation.
-
Product
PXI Strain Gauge Simulator Module 6-Channel, 3k
40-265-106
-
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 3kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Solar Simulator
Sirius 150A
-
Solar Simulators are used to simulate “real” solar radiation conditions and are widely used for the photovoltaic device research and QA etc.Beam collimation and spot uniformity are important properties along with spectral matching are key operational requirements. The SS150 and SS1000 are suitable for all types of solar cells and well match their optical requirements.
-
Product
Modbus Simulator & Tester
Modbus Poll
-
Modbus Poll is a Modbus master simulator designed primarily to help developers of Modbus slave devices or others that want to test and simulate the Modbus protocol. With the multiple document interface you can monitor several Modbus slaves and/or data areas at the same time. For each window you simply specify the Modbus slave ID, function, address, size and poll rate.
-
Product
Configurable Simulation Of ECU Diagnostics.
TestCUBE2
-
Softing Automotive Electronics GmbH
The ECU simulation TestCUBE2 is the counterpart for all cases of application in which an ECU is not yet (e.g. preparation of workshop tests) or no longer (e.g. tester regression test) available. TestCUBE2 is a configurable hardware and software solution for simulating ECU diagnostics with real bus communication. With just one device, you can simulate several ECUs or even an entire vehicle at the same time.
-
Product
Mechanical Simulation in Matlab
-
There are variety of numerical possibilities in the MATLAB and Simulink simulation environment. For those simulation environments we offer you various toolboxes that allow you to perform simulations easily and efficiently. These toolboxes can be combined with all available ways of MATLAB and Simulink. Our toolboxes can provide you support in the following areas: Analysis of structural dynamic behavior, Vibration and noise abatement, Design of active systems, Model Reduction, Ansys-Matlab interface.
-
Product
AIT PXI Express Test & Simulation Instruments
-
Avionics Interface Technologies
AIT’s Test & Simulation Instruments for MIL-STD-1553, ARINC 429, ARINC 664/Avionics Ethernet, and Fibre Channel are available in PXI and PXI Express form factors and are supported by software drivers for Windows, Linux, and LabVIEW Real Time. All instruments are also supported by Software Development Kits which provide API’s for C/C++, C#, and LabVIEW.
-
Product
Compensation Block for Thermocouple Simulator Modules
40-965-912
-
The Compensation Block is a accessory specifically designed for the 41-760 and 41-761 Millivolt Thermocouple Simulator modules. This block will give the user the temperature of the front panel junction of the module to cabling. This data can then be combined with other factors, temperature on the other end of the cable for example, to compensate the thermocouple hence increase the accuracy.
-
Product
Multiphysics Simulator
-
The COMSOL Multiphysics simulation environment facilitatesall steps in the modeling process defining your geometry, specifying your physics, meshing, solving and then post-processing your results. Model set up is quick, thanks to a number of predefined modeling interfaces for applications ranging from fluid flow and heat transfer to structural mechanics and electromagnetic analyses.
-
Product
Voltage Variation Simulator
KES7400A
-
The KES7400A Series comes in a single cabinet that consists of a Signal Generator module (including an arbitrary pulse generator), which combines our power supply technology and EMC technology, and a high-speed bipolar power supply module. Many automotive electronic devices have long wire harnesses and inductive load characteristics, as do motors, or capacitive load characteristics with a large-capacity capacitor connected between the input and ground. In the case of these devices, general DC power supplies exceed the linear operation range, potentially making it impossible to obtain the desired waveform output.
-
Product
PXI Automotive Switch Simulator Modules
-
Pickering's Switch Simulator Modules are designed for automotive test applications. These modules simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. They allow automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
USB 2.0 SmartCable For MIL-STD-1553 Test And Simulation
ASC1553
-
The ASC1553 (AIM SmartCable) USB module offers full function test, simulation, monitoring and recording for MIL-STD-1553B applications implemented in an ultra compact form factor.
-
Product
MIMIC® IoT Simulator
-
The MIMIC IoT Simulator creates a real-world test lab with many thousands of manageable IoT sensors, gateways and other connected devices to simulate your IoT environment related to*Industry 4.0*Smart Factories*Smart Cities*Smart agriculture
-
Product
Dual Channel Gigabit Ethernet Test & Simulation Instrument for PCI Express
PCIe-DCE
-
Avionics Interface Technologies
Dual channel, high precision Ethernet Test Instrument
-
Product
ARINC 664 Part 7 Test & Simulation Interface for PCI
PCI-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfacesSimulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboardError Injection including Runt Frames, Short IFG, and Invalid MAC FCS - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
2 Port BRI-S/T-U ISDN Simulator
BRI-2UST
-
The unit has two S/T and two U ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
Product
Single, Dual or Quad Stream MIL-STD-1553A/B Test and Simulation Module
APE1553-x
-
MIL-STD-1553 Test and Simulation Module for PCI Express with 1, 2 or 4 Dual Redundant channels (APE1553-1, APE1553-2, APE1553-4) plus 8 programmable discrete Input/Output channels. A unique feature of AIM’s APE1553-x module is the option for the MILScope™ capability. Models APE1553-1-DS/APE1553-2-DS integrate an onboard Analogue to Digital Converter (ADC) which samples, measures and stores the MIL-STD-1553 waveform. Automatic waveform validation is performed by the users Application Software or in conjunction with AIM’s PBA.pro Databus Test and Analysis Software and Test Scripts.
-
Product
Solar Array Simulator DC Power Supply
62000H-S
-
Chroma Systems Solutions, Inc.
Solar Array Simulator DC Power Supplies by Chroma provide programmable simulation of Voc (open circuit voltage) up to 1800V and Isc (short circuit current) up to 30A. The 62000S-H series provides an industry leading power density in a small 3U high package. The Solar Array Simulator is highly stable and has a fast transient response design, which are both advantages to MPPT performance evaluation on PV inverter devices.
-
Product
Gyro Simulator for Aircraft or Bench Use
TA-256A
-
This is a transformer isolated gyro simulator that can substitute for the KI256 attitude indicator and thus eliminate the requirement to remove that gyro to a remote stand and route a vacuum or pressure source out to the aircraft.
-
Product
ESD - Simulator
SESD 230
-
The test generator SESD 216 simulates electrostatic discharge as defined in the standard IEC / EN 61000-4-2. Depend on the Equipment Under Test (EUT) and the test set-up for laboratory tests the IEC standard shows two test methods
-
Product
4, 8 and 16 Channel ARINC429 Test and Simulation Module
ANET429-x
-
The ANET429-x is a member of AIM’s Ethernet based modules for analysing, simulating, monitoring and testing ARINC429 channels.
-
Product
Impulse Noise Simulators
INS Series
-
A simulator to reproduce fast rise-up noises which are generated when switching ON / OFF electric current on the inductive load. It can be used for performance evaluation of electronic equipment upon reproduction of line noises which are intruded to the power supply lines or induced noises onto the telecommunication lines.
-
Product
Battery String Simulator
BSS
-
AMETEK Programmable Power, Inc.
The Elgar Battery String Simulators (BSS) provide safe, reliable battery power for spacecraft testing. The broad range of features available ensures simulation capabilities for more than just two terminal power. It's the ideal solution for complete integrated system testing, not just battery elimination.
-
Product
Load Cell Simulators / Testers
-
A load cell simulator is a handy tool during initial setup, particularly of a batching by weight scale. It replaces the load cell(s) in the system allowing the scale technician to simulate various weights that will trigger the outputs setpoints for activating valves, gates, and mixers. These products are a must for anyone involved in scale installations and repairs.
-
Product
Lightning Surge Simulator
LSS-720B
-
Voltage surge test (1.2/50µs) and current surge test (8.2µs) specified under JEC-210 and 212 standard. (JEC: Japanese Electrotechnical Committe)High voltage surge test up to 20kV and high current surge test up to 4000A (30kV/6000A model available)
