Fading Simulators
test to verify wireless communicatons link in adverse transmission conditions.
-
Product
PCI Strain Gauge Simulator Card, 2-Channel, 350 Ohm
50-265-012
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
PXI/PXIe LVDT/RVDT Simulator Module, 2-Banks
43-670-103-AABBCC
Simulator
The 41/43-670-103 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types. It has two banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal.
-
Product
PXI/PXIe Resolver Simulator Module, 4-Banks
41-670-201-AABBCC
Simulator
The 41/43-670-201 is ideal for the simulation of Resolvers. It has four banks, each capable of simulating the output of a single 5 or 6-wire resolver.
-
Product
3U cPCI Synchro/Resolver Simulation Board
75DS2
Simulator
NAI’s 75DS2 is a Synchro/Resolver Simulation Board with four independent, isolated channels. These channels can incorporate up to four Digital-to-Synchro/Resolver Simulation Converters with 1.5, 2.2, or 3 VA drive capability, or either two or four Digital-to-LVDT/RVDT Simulation Converters. One of the outputs on each channel can be grounded without affecting performance.
-
Product
Single Stream STANAG3910 Electrica lTest And Simulation Module – Rafale – for PCI
APXX3910-EN
Simulator
Single Stream STANAG3910 Test and Simulation Module – Rafale – for PCI with 1 dual redundant HS/LS channel and onboard Electrical Front End. The APXX3910-EN is a functional replacement for model APX3910-EN.
-
Product
PXI RTD Simulator Module, 12 Channel, PT100
40-263-301
Simulator
The 40-263-301 is a 12-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
GPS Simulator
ADIVIC MP6220
Simulator
Multi-channel GPS simulator for GPS receiver position fix testIndividual channel is power adjustableSingle channel mode for receiver S/N ratio testTunable power output level from -160dBm to -55dBm
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for CPCI With 2 Or 4 CAN Bus Nodes
ACC825-3U-x
Simulator
ARINC825 (CAN bus) Test & Simulation module for CPCI with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACC825-3U-x CPCI card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
PCI Strain Gauge Simulator Card, 2-Channel, 3k
50-265-102
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
PXI Strain Gauge Simulator Module 2-Channel, 1.5K
40-265-402
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 1.5Ω) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Single Stream STANAG3910 Electrical Test & Simulation Module For 3U PXI Express/Compact PCI Express
ACE3910-3U-1-EN
Simulator
Single Stream STANAG3910 Test and Simulation module – Rafale – for PXI Express/Compact PXI Express with 1 dual redundant HS/LS channel and onboard Electrical Front End (EFE).
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, Simplified Current Sink, 750 V Isolation
41-752A-902
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Battery Simulator SoftPanel
A170202
Battery Simulator
For the products developed to connect batteries for use, if the battery is not ready or unable to be provided due to high cost, the 17020 battery simulator can be used to confirming the product functions during development. The applications of battery simulator include motor drives within the car system, OBC, D-D convertor or charger within the CSS system and products of DC bus, etc.
-
Product
Solar Array Simulator
62000H-S series
Simulator
The latest programmable solar array simulator power supply 62000H-S Series released by Chroma provide simulation of Voc (open circuit voltage) up to 1800V and Isc (short circuit current) up to 30A. The 62000H-S provides an industry leading power density in a small 3U high package. The solar array simulator is highly stable and has a fast transient response design, which are both advantageous to MPPT performance evaluation on PV inverter devices. The 62000H-S Series have many unique advantages including high speed & precision digitizing measurement circuits with a 100kHz A/D, 25kHz D/A controlled I-V curve and a digital filter mechanism. It can simulate an I-V curve accurately and response the mains ripple effect from the PV inverter. In addition, the built-in EN50530/Sandia SAS I-V model in the standalone unit can easily program the Voc, Isc, Vmp, and Imp parameters for I-V curve simulation, without a PC controller.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, 750 V Isolation
43-752A-003
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Battery Simulator
Battery Simulator
The battery simulator is used for testing satellite power supplies and is used in combination with a Solar Array Simulator and load systems (consumer simulation) for the validation and commissioning of satellite power supplies. Loads and power supplies in the battery simulator are operated in combination to represent a 2-square function and to simulate both charging and discharging of the battery.
-
Product
PXI Battery Simulator Module, 4-Channel, 5 Amp
41-754-011
Battery Simulator
The 41-754-011 and 43-754-011 are 4 channel battery simulators, capable of supplying up to 8 V and 5 A per channel. The channels are fully isolated from ground and from each other allowing series connection to simulate batteries in a stacked architecture. The isolation barrier (1000 V channel to GND and 750 V channel to channel) allows the module to be used as a battery stack representative of those used for vehicle propulsion..
-
Product
Mobile Communications DC Source, 15V, 3A
66311B
Battery Simulator
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66311B mobile communications DC source provides fast transient, exceptional sourcing, and precision measurement.
-
Product
Dual Port Simulator Fiber Channel PCI-X Module
PCI-X FC4 Simulyzer
Simulator
The modules are available as a single-function board - for analysis or for simulation / data generation - but also as a full-function board for simultaneous analysis and simulation. With a simple firmware/software upgrade, a single function board can become a full function board without having to purchase new hardware.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, 1 kV Isolation
41-752A-112
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI/PXIe LVDT/RVDT/Resolver Simulator Module, 2-Banks
41-670-003-AABBCC
Simulator
The 41/43-670-003 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types, as well as resolvers. It has two banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 2 channels of 5 or 6-wire or 4 channels of 4-wire.
-
Product
PXI RTD Simulator Module 12 Channel PT100
40-262-201
Simulator
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the design principles of our 40-260 PXI Precision Resistor, this RTD simulator module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels.
-
Product
PXI Battery Simulator Module
41-750-001
Simulator
The 41-750 is a battery simulator module that can be used to simulate the power supplies of cellular phones and other portable battery devices. It features fully floating output terminals than can deliver voltages up to 6 Volts. The fast responding remote sense connections allow the module to regulate the supply voltage at the device under test.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, 1 kV Isolation
41-752A-102
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI Strain Gauge Simulator Module 6-Channel, 1.5k
40-265-406
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 1.5kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
43-752A-913
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI/PXIe LVDT/RVDT/Resolver Simulator Module
43-670-XYZ-AABBCC
Simulator
The 41/43-670 range is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types, as well as resolvers. Available with up to four banks, each bank is capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 4 channels of 5 or 6-wire or 8 channels of 4-wire.
-
Product
Mobile Comm DC Source w/ Battery Emulation, DVM
66321D
Battery Simulator
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66321D mobile communications dc source provides fast transient response, exceptional sourcing, output resistance programming, and precision measurement. This product is specially designed for testing next generation digital wireless communications products. The 66321D mobile communications dc source offers a new capability that simulates the internal resistance of a battery or battery pack. Additionally, these high performance models offer improved transient response and stable output operation with either short or long load leads. The 66321D dc source provides all of the capabilities of the 66321B with the addition of a built-in digital voltmeter.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for PCI With 2 Or 4 CAN Bus Nodes
ACP825-x
Simulator
ARINC825 (CAN bus) Test & Simulation module for PCI with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825-x PCI card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
PCI Strain Gauge Simulator Card, 6-Channel, 350 Ohm
50-265-016
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
