Test Bench
worktable including instrumentation, fixturing and unit under test.
See Also: Test Benches
-
Product
Three Phase Meter Test Bench
-
Supreme Instrument Laboratories
Three phase meter test bench suitable for calibration & testing of AC Ammeters, Voltmeters, Single phase Energy Meters, Watt Meters, Power Factor Meters, Three Phase Two Wire & Three Phase Four Wire Energy Meters Trivector Meters, Maximum demand indicators, of active & reactive systems, Three phase 3 wire & 4 wire watt meters, Var Meters, Power Factor Meters etc.
-
Product
Universal test bench for optronic maintenance
COPI
-
COPI is a universal test bench used for test and maintenance of all kinds of optronic equipments.
-
Product
MCB Instantaneous Trip Test Bench
-
The SCR Elektroniks MCB Instantaneous Trip Test Bench is designed for Testing of MCB to carry out “Test of Instantaneous Tripping and of correct opening of the Contacts” as per IEC: 60898-1:2002 Clause 9.10.2 at rated voltage. This test is carried out with power factor between 0.95 and 1 with the sequence operation being O-t-CO-t-CO-t-CO with timings as specified in 9.12.11.1.
-
Product
ATE & Test Systems
-
Data Patterns' core business for over 20 years has been the development of Automated Test Equipment for critical aerospace requirements. Data Patterns developed a Multi Programmer with associated test automation software in 1994. Christened the DP-800 this product was adopted for the implementation of test rigs for Navigation Platform Test Benches, Engine Test Bed Automation, Cable Harness Test Systems, etc. This product was effectively utilized in the development of test benches required by Indian Space Research Organisation (ISRO) for the Polar Satellite Launch Vechicle (PSLV) and Geo Stationary Launch Vehicle (GSLV). Based on this foundation, the next generation test benches were developed in the cPCI architecture. Presently, Data Patterns develops cPCI based test systems for Laboratory applications as well as VME based test systems for challenging environmental conditions. Examples of test solutions built by Data Patterns are indicated below.
-
Product
Benchtop with Drop-In Test System
600 Series Compact ATE Platform
-
The Circuit Check 600 Series Compact ATE Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 600 Series Compact ATE, test procedures can become automatic, with test steps and go/no-go limits easily programmable. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
Product
Benchtop Test System
300 Series Benchtop ATE
-
The Circuit Check 300 Series benchtop ATE Test Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 300 Series Benchtop ATE, test procedures can become automatic, with test steps and go/ no-go limits easily programmable in common tabular form. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
Product
Test Bench Software
HORIBA TestWork
-
The versatile, customizable HORIBA TestWork operating software serves as a central tool for test bench management and control. Thanks to its high level of flexibility, it can be precisely tailored to a wide range of applications. At the same time, the intuitive interface enables fully automated execution of even complex test runs without losing sight of the essentials.
-
Product
Test Benches
-
Our range of test benches is designed for accurate measurement, performance validation and quality control of electrical components and systems. They provide standardised and customised AC and DC testing, with variable signal frequencies and waveforms.
-
Product
AXIe Switch Module
PK100x4
-
The PK100x4 AXIe module implements a 100x4 matrix switcher structure (100 inputs – 4 outputs). The module is designed to work in functional control systems, systems for monitoring and diagnostics of ground-based electronic equipment, control systems for bench tests.
-
Product
Pitot / Static Tester for Laboratories and Workshops
ADSE 741
-
The ADSE 741 is a complete high performance three channel Ps, Pt and AoA stand-alone test bench specially designed to be used in the workshop or in the laboratory to test and calibrate all air data equipment such as altimeters, vertical speed indicators, air speed indicators, pneumatic AoA (Angle of Attack) indicators, MACH-meter, air data computers, specific probes and sensors.The high precision embedded sensors enable the ADSE 741 to be used as a pressure standard.The user interface is programmed underWindows and Labview, with a data base managed in a spreadsheet for easy evaluation, management, statistics and presentation.
-
Product
Buchholz Relay Test Benches
-
HAOMAI Electric Test Equipment Co., Ltd.
Buchholz relays are used to protect transformers, and these test benches perform necessary quality and performance checks.
-
Product
Functional test
-
Maschinenbau Haldenwang GmbH & Co. KG.
Test bench for small vehicles with 2 wheelsRoad load simulationDetermination of maximum speedMeasurement and evaluation of speed, speed, distance traveledDisplay of wheel power at test speedDisplay on your PC monitorExpression of test resultsCustomer and vehicle databaseEuro system console MCD 2000 with switching elements for roller setPort for external devices
-
Product
High-Performance Autoranging DC Power Module, 60V, 20A, 300W
N6754A
-
This module is used in both the small, multiple output 1U high N6700 Low-Profile Modular Power System (for ATE systems) and the multiple output N6705 DC Power Analyzer (for bench testing). GPIB, LAN, USB, and LXI compliance are standard. Select from more than 20 different DC power modules, ranging in capability from basic to high precision, and in power from 20 - 300 W.
-
Product
PC Based Comprehensive Test Setup for Luminaires
-
Our zest for innovation has resulted in continuous upgrades in the existing line of products. Till now we used to manufacture 3 different equipments for Driver, MCPCB and Luminaires Component testing. We at SCR Elektroniks have developed our comprehensive tester to incorporate all the 3 systems in a single bench. Here in this tester one can test all the three DUT in a single bench. Since all the 3 testing procedures have many tests in common, we have incorporated all the tests in a single bench such that testing of Luminaire driver, Luminaire PCB and Final Luminaire set is performed in single test bench. Only these tests are performed over the DUT else other are disabled for them.
-
Product
Complete Transformer Test Bench
-
Weshine Electric Manufacturing Co., Ltd
Our multifunction Transformer Test Bench (VS-ZHSY Series) is intuitive with all of the ease of working with individual, dedicated instruments. We deliver this experience through our design philosophy. Rather than producing a single, complex system with afterthought towards rendering it friendly, we uniquely combine several intelligent instruments packaged as a single system.
-
Product
Laser Testing
-
CI Systems provides a wide range of laser testers, whether stand-alone systems, such as Depot Field Laser Tester, Depot Laser Tester or integrated in a multi-sensor electro-optical test bench. These testers can also be integrated with CI Systems' standard Laser Tester software and PC package to serve as the necessary testing tool for a larger system comprising a Laser Range Finder, Laser Marker and Laser Designator.
-
Product
Manually Variable Attenuators
-
The JFW 50 Ohm dual rotary attenuator has been a staple tool to RF engineers for over 30 years. Our years of proven quality and performance make our manually variable attenuators right for any RF environment. Whether you are using the rotary attenuator on your RF test bench or mounting it to a panel, the JFW dual rotary attenuator makes adjusting attenuation quick and easy.
-
Product
Modular Multilevel Converter (MMC) Test Bench
-
Research into innovative HVDC interconnections and FACTS applications requires a flexible hardware architecture that allows testing of new topologies and switch configurations.
-
Product
Fuel Display Unit Tester
MS 1125
-
Fuel Display Unit Test Bench is a compact table-top test bench with front panel controls, indications, built-in signal simulator and necessary power supply for testing the serviceability of Fuel Display Unit of Helicopter. FTB operates on 230 V AC and supplies 28 V DC power to FDU. FTB is housed in a metallic cabinet FTB interfaces with both 61 Pin connector and 6-pin socket mounted on the rear panel of FDU by means of the cable connected to the unit. FTB is fabricated utilizing off-the-shelf standard industrial/commercial components like rotary switches, toggle switches, press switches, test sockets, fuse holders, potentiometer etc. The Frequency generation circuit is integrated into FTB for the simulation of Fuel probe and flow rate signals. The frequency of the signal can be selected by means of a rotary switch Low amplitude sine wave signal is simulated for testing flow rates. Variable voltage DC power supply with a voltage range of 24 to 29 Volts is provided within FTB to power-up FDU. 5 V DC is provided for the operation of signal generating circuit (PIC Frequency Controller Board). An off-the-shelf Hand held battery operated Digital Multimeter (DMM) procured from the prominent manufacturer (FLUKE) is supplied with FTB for setting up and measurement of various parameters like Resistance, Voltage, Frequency etc.
-
Product
MCB Temperature Rise and Power Loss Test Bench
-
The SCR Elektroniks 3 station MCB Temperature Rise and Power Loss Test Bench is economically designed to verify temperature rise and measure power loss as per clause 9.8 of IEC 60898 with the circuit designed to follow test procedure as per Cl 9.8.2. The temperature rise is measured in accordance with Cl 9.8.3 and 9.8.4 while power loss is measured and verified as per Table 15 of Cl 9.8.5.
-
Product
Dynamometer Power Supply
DES Series
-
The DES 310 and DES 311 power supplies are suited to the entire range of Magtrol's Eddy-Current and Powder Brake Dynamometers. To avoid any disruption of the surrounding electronic modules, the DES 310 / DES 311 supplies are fitted in an industrial housing made of extruded cast aluminum. This housing must be installed directly on the test bench, as near to the dynamometer as possible.
-
Product
Phase Angle Meter
597C
-
Red Phase Instruments Australia Pty Ltd.
The Model 470A has similar software and performance as the Model 465C. It is packaged in a 19? style bench-top case with all connections on the front panel for use in meter test benches. It has inputs for comparison with another polyphase standard or 3 separate single phase standards for verifying calibration accuracy.
-
Product
Virtual tester
-
Emulate tester patterns in simulation environment with DUT simulation model. The simulation allows pre-silicon debug of test programs. Reads the actual ATE program and creates a Verilog /VHDL simulation test bench.
-
Product
Flowbenches
-
The product that started it all for SuperFlow, a simple device to measure and quantify the amount of air-flow through cylinder head runners and intake manifolds. In the 1970s the goal was to win Formula V races, a hobby of SuperFlow’s founder. Today, SuperFlow produces a series of air flow test benches used for things like increasing engine performance and fuel economy, developing catalytic converters and certifying their flow rates at the end of a production line as well as a variety of other air flow test applications across multiple industries.
-
Product
High Flexibility VNA Cables
-
Our lines of high frequency VNA test cables display excellent electrical properties such as wonderful phase stability of +/- 6° at 50 GHz and +/- 8° at 67 GHz as well as VSWR of 1.3:1 at 50 GHz and 1.4:1 at 67 GHz. The 50 GHz assemblies are terminated with 2.4mm connectors while the 67 GHz versions utilize 1.85mm connectors. The braided stainless steel armoring surrounding the coax provides a rugged, but flexible cable with a flex life exceeding 100,000 cycles, making these test cables ideal for use in semiconductor probe testing, precise bench top testing as well as lab/production testing where the need for a highly flexible, yet durable cable solution is required. The VNA test cables are also equipped with rugged stainless steel connectors that provide up to 5,000 mating cycles when attached with proper care. Additionally, the flexibility of these cables makes it easier and safer to test a Device Under Test (DUT). A swept right angle 2.4mm and 1.855mm connector option allows these cables to fit in tight spaces and can reduce the length of cable required in many applications.
-
Product
High-Power, Rack-Mount Amplifiers
-
High-power, rackmount amplifiers utilize advanced power combining techniques to achieve high output power levels. These integrated amplifiers include advanced cooling capabilities and other customizable features. Though a focus on modularity, these rackmount amplifiers are ready for easy integration into a larger system or lab test bench.
-
Product
Solid Oxide and Molten Carbonate Fuel Cell Test Stations
-
Greenlight''s SOFC test systems include options for integrated reformers, de-sox, gas mixing, water saturation, pre-heating, furnace, heat recovery and water balance. These SOFC test rigs can be configured to operate on gaseous or liquid fuels, with operating temperatures up to 1000C. Pressure control is optional and furnaces can be tailored for either planar or tubular cell configurations. For single cell or button cell testing, Greenlight offers the X20 table-top SOFC test bench, including furnace and optional fixtures.
-
Product
Pitot Static Indicator
ADSE 740
-
The ADSE 740 is a complete high performance dual pressure Ps and Pt standalone test bench specially designed to be used in the workshop or in the laboratory to test and calibrate all air data equipment such as altimeters, vertical speed indicators, air speed indicators, MACH-meter, air data computers ...) and sensors.
-
Product
Capture & Replay System
-
PacketStorm Communications, Inc.
The PacketStorm CRS is a packet capture and replay system with hardware time stamping at 10Gbps. The user specifies which packets to capture based on the filter parameters. Packet captures can be continuous or stop capture after a certain number of frames, bytes, or time. The 10G filters include: Source Address, Destination Address, Source Port, Destination Port, and Protocol. The CRS file management includes automatic file compression and decompression. Operation is via the console or the remote GUI. There are two CRS versions: 1U and Lunchbox. The 1U version is intended to be installed in a rack or on a test bench. The lunchbox version includes a keyboard, mouse, and monitor and is intended to be moved about between stations and labs.
-
Product
DMX Tester
DMXter 2U
-
Here's the DMXter 2U, a Lil'DMXter2 for bolted down applications. All the hardware and software features of the standard Lil'DMXter2 in a 2U 19" rack box, plus many new features.The user controls, the XLR connectors, and the LED illuminated LCD display are on the front panel. The 2U is equally at home as the back up controller in a theatre or TV studio, running a trade show booth, the background lighting for themed entertainment or as the built in test controller in a touring show DMX distribution rack. Its increased I/O capabilities will make it a useful addition to your test bench.
