Filters
Electronic circuits which refine signal by blocking certain frequencies, while allowing other frequencies to pass.
See Also: Filter / Amplifiers, EMI Filters, Low Pass Filters, Programmable Filters, Attenuators
-
Product
Bench/portable Universal Counters With USB Interface 3GHz Or 6GHz
TF900 Series
-
Frequency, period, pulse width, frequency ratio, duty cycle, and event counter modesDC to 3000 or 6000MHz range, 0.001mHz resolutionHigh impedance measurement up to 125 MHzAC or DC coupling, 1M/50Ohm selection, polarity invertSwitchable attenuator, threshold controlNoise filter for low frequency measurementsSelectable measurement time; display hold functionLarge 10 digit display with full range of annunciatorsInternal rechargeable batteries for portable useUSB interface provides full remote control and readback
-
Product
Public Switch Telephone Network Tester
295B
-
The Testphone 295B is a test telephone designed for use on Public Switched Telephone Networks (PSTN). It is designed for use on both Dual-tone Multi-frequency (DTMF - tone dialling) and Loop Disconnect (LD - pulse dialling) lines. Fitted with an integral ADSL filter, the telephone will not cause interference when connected to ADSL/Broadband lines in either `on hook` or `off hook` mode.
-
Product
Harmonic Filter Resistors
-
Post Glover designs, builds and tests their harmonic filter resistors in accordance with applicable IEC and IEEE standards to guarantee their performance. With no two installations ever being the same, our experienced engineers develop the proper solution for your particular application and environment. Our low inductance designs are built using all stainless steel elements in corrosion resistant enclosures chosen for your unique specification. Request a quote for your custom harmonic filter resistor.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-02 And WMA-02LF
-
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Band Pass Filters
-
High-Pass (HPF series), Low Pass (LPF series) and Band Pass (BPF series) Filters are available, providing desired skirt selectivity and rejection levels with minimum insertion loss in the pass band. The filters are offered in all standard waveguide bands covering 18 to 400 GHz depending on our possibility to fulfil the customers' requirements. Dimensions of filters depends on required specifications. .
-
Product
6-Channel SD/ED/HD Video Filter With Charge Pump
ADA4424-6
-
The ADA4424-6 is a high performance video reconstruction filter specifically designed for consumer applications. It consists of a standard definition (SD) section with two fifth-order Butterworth filters, and a high definition (HD) section with three fifth-order filters. The SD section contains an internal Y/C summer for CVBS output, whereas the HD section provides selectable corner frequencies for either extended definition (ED) or HD signals.
-
Product
USB-5132 , 50 MHz Bandwidth, 2-Channel, 8-Bit USB Oscilloscope Device
780468-01
Oscilloscope
50 MHz Bandwidth, 2-Channel, 8-Bit USB Oscilloscope Device - The USB‑5132 low-cost oscilloscope device has two channels that sample up to 50 MS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes and an instrument driver that includes data streaming and analysis functions. This device is ideal for portable and benchtop applications with fast signals that require flexible measurement configurations and up to 50 MHz of analog bandwidth.
-
Product
Passive Component Integration
Passive Component Integration
Integrate passive optical components of your choice such as WDM couplers, splitters, band-pass filters, PM beamsplitters and circulators. PXIe and benchtop models support SMF, MMF and PMF.
-
Product
Mezzanine System
5147
System
ECM P/N 5147 provides two channels of 12 bit A/D conversion using the Analog Devices AD9235, and is suitable for medium resolution high speed applications. The two differential inputs are terminated in 120 ohms and buffered with a gain of 1 differential amplifier. Differential Input range is +/-3.0V. Sample rates are 20MHz per channel with a 5MHz 4 pole elliptical analog input filter.
-
Product
ICE 4000 Series
ICE4003
-
The ICE4003 is a dual channel filter that provides two independent UHF TX/RX channels in a single package. Each channel can operate autonomously into a dedicated antenna or both channels can be combined into a single antenna. Furthermore, the combiner used in the ICE4003 is capable of combining any combination of TX/RX signals while minimizing path loss. Currently, supported radios include the ARC-225 and ARC-210. The ICE4003 is designed with a flexible interface to support future radio requirements, such as JTRS. A mounting tray is available as an option for easy incorporation on your platform. Cost-effective modifications are available on the ICE4003. Please contact your sales representative at 513.870.9060 or Support@PoleZero.com for details.
-
Product
Ethernet/LXI digitizerNETBOX 14 Bit High Speed Digitizer - 500 MS/s on 12 Channels, 12 Single-Ended Inputs
DN6.445-12
Digitizer
The digitizerNETBOX DN6.44x series allows recording of up to 24 synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
System for Analysis and Jamming of 10/25/40/50/100Gbps Ethernet and Gen 6 (32G) Fibre Channel
SierraNet M328Q
-
The SierraNet M328Q™ system provides for analysis and jamming of 10/25/40/50/100Gbps Ethernet and Gen 6 (32G) Fibre Channel data capture and protocol verification for developers & protocol test engineers in LAN, SAN, NAS and other Ethernet and Fibre Channel applications. Available with two QSFP28 FlexPorts™ for maximum configuration and utility, the SierraNet M328Q includes an easy to use, customizable software interface, large capture buffers, and the most advanced capture, triggering, impairment and filtering capabilities in the industry.
-
Product
Digital Input Board, 16 Isolated Channels, 24V
APCI-1016
-
*16 digital inputs, 24 V Optical isolation 1000 V Input filter*Protection against pole reversal*Standard drivers for:*Real time drivers for Windows 2000/NT/98.*The board is supplied with the universal software ADDIPACK.
-
Product
Microphone Preamplifier
426A11
-
1/2-inch ICP preamplifier with gain and filter switches (for prepolarized microphones)ICP(R) low noise preamplifier with gain, filters, and TEDS
-
Product
Fast Tuned Notch Filter
ES005 & ES006
-
Teledyne Defence & Space’s (TDS) range of Fast Tuned Notch Filters (FTNF) have been designed to protect Electronic Support Measures (ESM) receivers from high duty cycle, frequency agile interference produced by on board (or cohort) combat radar systems. ESM sensors often need protection from high power nearby radars, and such signals can reduce receiver dynamic range.
-
Product
PXI-5105, 60 MHz, 8-Channel, 12-Bit PXI Oscilloscope
779685-02
Oscilloscope
60 MHz, 8-Channel, 12-Bit PXI Oscilloscope—The PXI‑5105 high-density PXI oscilloscope device has eight simultaneously-sampled channels with flexible settings for coupling, impedance, voltage range, and filtering. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with many channels that require up to 60 MS/s or 60 MHz of analog bandwidth. The PXI‑5105 also features PXI synchronization and data streaming capabilities.
-
Product
Low-PIM, Low-Power Filter Solutions for Monitoring Broadband Emissions
-
Bandpass/Bandstop, Notch, and HighpassCompact Design for Rack Mounting of Several BandsSuitable for Monitoring Emissions from Semiconductors,TX/RX Chipsets, SAW/BAW Filters, Cell Phones,Printers, PDA’s, etc.
-
Product
0.5-18GHz High Performance Receiver
QR026
-
The Teledyne Defence & Space (TDS) Single Channel High Performance Receiver provides a new approach for ESM / ELINT applications, incorporating patented features offering wide band synthesized capability from 500MHz to 18GHz, with frequency extensions available up to 40GHz.TDS’s new QR037 digital receiver module combines high dynamic range RF down conversion and LO generation with digitisation and signal processing capabilities to provide a compact solution for a number of ELINT/COMINT and ESM applications.Excellent dynamic range and linearity is achieved through a combination of RF and digital down conversion stages coupled with high performance pre-selection and IF filtering.
-
Product
Network Interface Card
NIC10G
Interface Card
Featuring the Intel 82599ES dual 10GbE controller, the NIC10G supports flow control, integrated IPsec security engines, optimized queues, IPv6 offloading, advanced filtering capabilities, and Tx/Rx IP, TCP and UDP checksum offloading capability. Also has integrated a PCI Express Gen 2 interface supporting up to 8 lanes.
-
Product
Roughness Testers
-
Roughness is an important parameter when trying to find out whether a surface is suitable for a certain purpose. Rough surfaces often wear out more quickly than smoother surfaces. Rougher surfaces are normally more vulnerable to corrosion and cracks, but they can also aid in adhesion. A roughness tester is used to quickly and accurately determine the surface texture or surface roughness of a material. A roughness tester shows the measured roughness depth (Rz) as well as the mean roughness value (Ra) in micrometers or microns (µm). Measuring the roughness of a surface involves applying a roughness filter. Different international standards and surface texture or surface finish specifications recommend the use of different roughness filters. For example, a Gaussian filter often is recommended in ISO standards.
-
Product
EMI Filter/TVS Arrays
-
ProTek offers TVS protection and EMI Filtering all in one package. These space saving devices are ideal for use in portable electronics such as Cellular Phones, Cellular Phone Accessories, Laptops, and PDAs.
-
Product
UV TOCONs
-
SiC based UV sensor with integrated amplifier and 0 – 5 V voltage output. Measures intensities from 1.8pW/cm² up to 18W/cm². Spectral response for broadband UV or filtered for UVA, UVB, UVC or UV-Index. Also available for blue light (GaP chip) or visible light (Si chip) measurement. Available in TO5 housings or as miniature sensor probes (stainless steel or plastic). Special TOCONs for hydrogen flame sensing (TOCON_F) and for fire detection (TOCON_N) available. Also available for operating temperatures up to 120°C (standard is 85°C). Please learn more about the sglux TOCONs here: TOCON selection guide and here: TOCON User Guide.
-
Product
Acoustic Wave Device
-
Murata offers high-performance acoustic wave radio frequency (RF) devices including filters, duplexers, diplexers, resonators, and frequency control devices. This allows us to provide a wide range of acoustic wave-based RF devices in a one-stop service to all RF engineers.
-
Product
Digital Storage Oscilloscope
DCS-1000B Series
-
*100MHz/70MHz/50MHz Digital Storage Oscilloscope*Waveform update rate up to 50,000wfms/s*256 color gradient 7inches WVGA display*10M memory depth per channel independently*1M FFT mathematical sampling analysis mode*Zoom In/Play and Pause Function*Diversified Trigger Functions*X-Y Mode Display*Go/NoGo Function*Data Log Function*Digital Filter Function*36 Measurement Parameter Selections
-
Product
Miller 400D
44550
-
No need to select ranges or adjust dials – the Miller 400D provides a direct read-out of resistance with the push of a button• Bluetooth interface allows optional data-logging via a Bluetooth-enabled PC (or PDA)**• Rugged, hard plastic case - safe to use on wet ground – IP67 rating for dust and water intrusion• Resistance measurement range from 0.01Ω to 10MΩ (auto-ranging) • High resolution digital display• Resistance measurements are unaffected by any stray interference signals that may be present in the earth during readings, due to the use of narrow band-pass filters centered at 82.2Hz (the unit’s operating frequency)• Runs on a set of replaceable D-cell alkaline batteries...no need to periodically recharge the unit or to plug it into a power source• Performs 10,000 single readings on a fresh set of batteries• Integrates with Universal Rectifiers’ Soil Depth Selector/Multi-Pin Cable Harness System (please see Integration with Universal Rectifiers’ Cable Harness)
-
Product
OEM Module For Conversion Between IP And ASI
DTM-3200-RA
-
The DTM-3200 converts IP to ASI, or ASI to IP. Integrate this compact module to extend the range of I/O standards supported by your product. Technical highlights include advanced IP-jitter filtering, ultra-low latency and zero-jitter IP transmission.
-
Product
AC & DC Capacitors
Power Electronics
-
AC & DC capacitors for power electronics applications with high current and harmonic distortion. DC capacitors for power inverters for railways, welding, energy storage and filtering applications. Typical applications: inverter, filtering, switching, high power lighting, traction and railways, welding, PFC with high voltage and high harmonic application (i.e. Wind turbines).
-
Product
AC/DC Power Capacitors
ACF Series
-
For 70Vac~400Vac / 100Vdc~700Vdc Pulse Current requirement, please refer to our DC Pulse Current Capacitors for Power Electronic applications.For continuous and High RMS Current requirement, please refer to our High AC Current Capacitors LC series, which support continuous duty even at +105C.We manufacture AC Filter Capacitors for a wide variety of applications with different Capacitances, Voltages, Discharge Energy ranges, dv/dt, Pulse Discharge Currents, RMS Currents, frequency ranges, size restriction and even capacitor mountings.
-
Product
Remote Monitor Management Information Base
SNMP RMON MIB
-
For every control table in the MIB, create and delete rows with various combinations of SNMP requests (all variables in a single request throughall variables in individual requests).Determine which row of this table is modeling the ethernet interface connected to the agent (requires that we are using ethernet). Check that this is for the same interface discovered in the "interfaces" test. Check counters.Build a history control row pointing to the interface connected to the agent. Check validity and traffic reported.Test agent's ability to generate an alarm on an RMON variable, then on threshold condition. Test for support of alarms on failing events, and in the event of target variable vanishing.Set up agent to track hosts on the ethernet interface connected to the agent. Check that entry was added for Rmon device's own ethernet address.Generate various top N reports (hostTopN test) and check validity.Start a matrix capture and check that the src-dst and dst-src tables are in sync.Check a channel and check for event generation (filter test).Create a channel and start a capture. Test locking and wrapWhenFull operation.
-
Product
PCI-5105, 8‐Channel, 12-Bit, 60 MHz Bandwidth PCI Oscilloscope Device
779686-01
Oscilloscope
8‐Channel, 12-Bit, 60 MHz Bandwidth PCI Oscilloscope Device—The PCI‑5105 high-density oscilloscope device has eight simultaneously-sampled channels with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with many channels that require up to 60 MS/s or 60 MHz of analog bandwidth.
