Isolated Digital Input Cards
-
Product
Temperature Module
U1586B
Temperature Input Module
The U1586B temperature adapter expands the capabilites of your handheld oscilloscope or handheld digital multimeter to measure temperature, either in °C of °F. To be used with a K-type bead thermocouple, and with approximately 1600 hours battery life with an alkaline battery, this adapter ensures you get the most out of your handheld scope or DMM purchase.
-
Product
PCIe 8 Bit High Speed Digitizer - 2.5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4I.2220-X8
Digitizer
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PCIe 16 Bit High Speed Digitizer - 180 MS/s on 2 Channels
M4I.4470-X8
Digitizer
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Digital Multimeter Device
Digital Multimeter
Digital Multimeters measure voltage, resistance, current, capacitance, inductance, and temperature. Some models also have an isolated digitizer mode. Use these products to test consumer electronics, fuel cells, aerospace production, and more.
-
Product
PCIe-5774, 12-Bit, 6.4 GS/s, DC-Coupled, 2-Channel PCI FlexRIO Digitizer Device
785648-02
FlexRio Digitizer
The PCIe-5774 is a PCI FlexRIO Digitizer Device that provides up to 3.2 GHz of DC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5774 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The voltage ranges are software-selectable and include 200 mV peak-to-peak and 1 V peak-to-peak, with a selectable DC offset.
-
Product
PXIe-4353, 32-Channel, 24-Bit PXI Temperature Input Module
781348-01
Analog Input Module
32-Channel, 24-Bit PXI Temperature Input Module—The PXIe‑4353 is a thermocouple input module that provides integrated data acquisition and signal conditioning for temperature measurements. The PXIe‑4353 includes increased accuracy and synchronization features for scalable measurement systems from low‑ to high‑channel counts. The high accuracy is attributed to the NI TB‑4353 isothermal terminal block that optimizes thermal conductivity between the thermocouple terminals and the cold-junction compensation (CJC) channels. The PXIe‑4353 has two auto zero channels for offset compensation as well as open thermocouple detection to identify disconnected thermocouples.
-
Product
PXI Strain/Bridge Input Module
Strain/Bridge Input Module
PXI Strain/Bridge Input Modules feature up to eightchannels that support quarter-, half-, or full-bridge sensors at speeds up to 102.4kS/s. The modules provide increased accuracy, high data throughput, and a range of synchronization features. Optional features include remote sensing, internal bridge completion, and shunt calibration options per channel. PXI Strain/Bridge Input Modules are ideal for dynamic strain, load and pressure measurements, and test cell installations requiring accuracy and flexibility.
-
Product
PCI-6528, 48-Channel, 24 Sink/Source Inputs, 24 Sink/Source Outputs, Channel-Channel Isolated, Digital I/O Device
778833-01
Digital I/O Module
The PCI-6528 is an industrial, parallel digital I/O interface.With programmable power-up states, you can configure the initial output states in software, to ensure safe … operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6528 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
PXI Semi-Dynamic Digital I/O Module, 64-Channel
40-419-001
Digital I/O Module
The 40-419-001 is a 64-channel digital I/O module suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. It can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
Product
10-CH General-Purpose Timers/Counters & 8-CH Digital I/O Card
PCI-8554
Digital I/O Module
- Supports a 32-bit 5 V PCI bus- On-board four 82C54 programmable timer/counter chips- 10-CH independent 16-bit down counters- 1-CH 32-bit cascaded timer- Four programmable clock sources for each timer/counter
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 125 MS/s on 4 Channels (Single Ended) or 2 Channels (Differential)
M2P.5962-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
1 MS/s, 12-Bit, 16-Ch Multifunction PCI Card
PCI-1712
PCI Card
16 single-ended or 8 differential or a combination of analog inputs12-bit A/D converter, with up to 1 MHz sampling rateTwo 12-bit analog output channels with continuous waveform output function16-ch digital input and 16-ch digital outputThree 16-bit programmable multifunction counter/timers on 10 MHzProgrammable gainAutomatic channel/gain scanningOnboard FIFO memory (AI: 1,024 samples AO: 32,768 samples)Auto-calibration (AI/AO)PCI-Bus for data transferPre-, post-, about- and delay-trigger data acquisition modes for analog input channelsFlexible triggering and clocking capabilities
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 2.5 GS/s on 4 Channels, 1.5 GHz Bandwidth
DN2.222-04
Digitizer
The digitizerNETBOX DN2.22x series allows recording of up to 8 channels with sampling rates of 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786163-01
FlexRio Digitizer
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
Industry Pack Carriers and Digital I/O
CPCI-4pack-6U
Digital I/O Module
The CPCI-4pack-6U module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the CPCI-4pack-6U is the perfect solution. The Local DSP can be used to simply move data to and from the CPCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc. Custom application software can be downloaded to the DSPvia the CPCI bus or the local serial port.
-
Product
PCIe Digital Waveform Acquisition with Programmable Threshold - 720 MBit/s Internal Sampling Rate Timing, 700 MBit/s External State Clock
M4I.7730-X8
Digital Waveform
The M4i.77xx-x8 series digital waveform acquisition (logic-analyzer) cards include versions with 32 synchronous channels, either single-ended with programmable threshold levels or differential. The large onboard memory can be segmented to record different waveform sequences. While the M4i.77xx cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum digital acquisition cards. Therefore existing customers can use the same software they developed for a 10 year old 60 MS/s digital input card also for an M4i.77xx series 720 MS/s logic analyzer.
-
Product
NI-9239 , ±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module
780181-01
Voltage Input Module
±10 V, 50 kS/s/ch, 24-Bit, Simultaneous Input, 4-Channel C Series Voltage Input Module - The NI‑9239 performs differential analog input. With channel‑to‑channel isolation, your entire system, including the device under test, is protected from harmful voltage spikes up to the isolation rating. In addition to safety, isolation eliminates measurement errors caused by ground loops because the front end of the module is floating. Designed for both speed and accuracy, the NI‑9239 is an effective general-purpose analog module because of its resolution, sample rate, and input range.
-
Product
PXIe Digital I/O: 28 LVDS Channels, 8 Trigger Channels
M5302A
Digital I/O Module
M5302A is a single-slot Digital IO PXIe module with 28 programmable LVDS channels and 8 single-ended channels. The LVDS channels can be used to communicate to the device under test or can be used to control other devices by emulating protocols such as Camera Link. The single-ended channels are suitable for event triggers or other general-purpose IO applications.
-
Product
Handheld Digital Multimeter Transit Case, Aluminum-clad
U1172A
Digital Multimeter
Use this aluminum-clad case to transport your handheld digital multimeters (DMMs).
-
Product
sbRIO-9207, Non-Enclosed, 500 S/s, 16-Channel C Series Voltage and Current Input Module
781069-01
Current Input Module
Non-Enclosed, 500 S/s, 16-Channel C Series Voltage and Current Input Module - The sbRIO‑9207 is a combination voltage and current input module designed with industrial systems in mind. It features eight current and eight voltage input channels, with built-in noise rejection. Non-enclosed modules are designed for OEM applications.
-
Product
ARINC 429 Multichannel Interface Card for Mini PCI Systems
DAS-429mPCI/RTx
Interface Card
The DAS-429mPCI/RTx is an ARINC 429, multichannel interface card for Mini PCI systems. The card’s small size and suitability for Mini PCI notebook computers, make them a complete solution for developing and testing ARINC 429 interfaces and for performing system simulation of the ARINC-429 bus, both in the lab and in the field.The DAS-429mPCI/RTx is supplied with C drivers, including source code and Mystic application program.
-
Product
PXI Analog Input Module
Analog Input Module
PXI Analog Input Modules feature multiple analog-to-digital converters (ADCs) as well as built-in signal conditioning. Sample rates range from 5 kS/s/ch to 2 MS/s/ch. You can choose from modules that offer up to 28 bits of resolution and up to 32 simultaneous channels. PXI Analog Input Modules offer different types of isolation and filtering, so you can choose options that meet specific application needs. The modules promote increased accuracy, high data throughput, and are ideal for scalable measurement systems with low and high channel counts.
-
Product
High Performance 50 MHz Dynamic Digital I/O PXI Subsystem
GX5960 Series
Digital I/O Module
The GX5960 digital subsystem represents the highest level of performance available for PXI-based digital instrumentation and features high performance pin electronics and a timing generator / sequencer in a compact, 6U PXI form factor. The GX5960 series consists of the GX5961 clock generator board with 16 driver / sensor channels and the GX5964 driver / sensor board which supports 32 bi-directional I/O channels. Up to 528 digital I/O channels can be supported by the GX5960 digital subsystem. Each digital channel features a wide drive / sense voltage range of -14 V to +26 V (maximum swing of 24 volts) which can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and a load value (with commutation voltage level) – offering the user complete flexibility when creating test programs and fixtures for multiple UUTs. In addition, each channel offers a parametric measurement unit (PMU) for DC measurements.
-
Product
NI-9401, 5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module
782401-01
Digital Module
5 V/TTL, 8 Bidirectional Channels, 100 ns C Series Digital Module - The NI‑9401 is a configurable digital I/O interface for input or output in 4‑bit increments. Therefore, the NI‑9401 can create three configurations: 8 digital inputs, 8 digital outputs, or four digital inputs and four digital outputs. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the NI‑9401 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and more. Each channel features transient isolation between the I/O channels and the backplane.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786165-01
FlexRio Digitizer
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PCIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
PXI Digital Multimeter, 6 digit, Enhanced Performance
M9183A
Digital Multimeter
The Keysight M9183A is a 6 digit PXI digital multimeter that measures common parameters such as DCV, DCI, ACV, ACI, 2- and 4-wire resistance, frequency, capacitance, and temperature. It offers40 ppm basic DCV measurement accuracy, excellent noise rejection, and handles inputs of up to 300 V.
-
Product
NI-9475, 60 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module
780132-01
Digital Module
60 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module - The NI‑9475 works with a variety of industrial devices such as solenoids, motors, actuators, relays, and lamps. Each channel sources up to 1 A at levels up to 60 VDC and features isolation from … channel‑to‑earth ground.
-
Product
DIOS (Digital I/O Scan Module)
JT 2122/MPV
Digital I/O Module
The JT 2122/MPV DIOS (digital I/O scan module) increases the coverage and improves the diagnostic resolution of boundary-scan testing by extending test access to connectors and/or test points. JT 2122/MPV DIOS provides bi-directional parallel-scan access to up to 128 or 133 I/Os in a standard DIMM-168 module.
-
Product
1 Meter Long SCSI Cable with 100 Pin Connector
U2903A
Digital Cable
The Keysight U2903A is an accessory compatible and recommended to be used with the U2600A Series USB used with the U2600A USB Modular Digital I/O modules. The pin-outs of the U2903A is dependent on the USB Modular Digital I/O module that it is working with. For more information, please refer to the data sheet or the user guide of the USB Data Acquisition unit that U2903A is to be used with.
-
Product
NI-9203, 200 kS/s, ±20 mA, 8-Channel C Series Current Input Module
783731-01
Current Input Module
200 kS/s, ±20 mA, 8-Channel C Series Current Input Module - The NI‑9203 is intended for high-performance control and monitoring applications. It features programmable input ranges and variable connectivity options. To protect against signal transients, the NI‑9203 … includes a channel‑to‑earth ground double‑isolation barrier (250 Vrms isolation) for safety and noise immunity.
