Isolated Digital Output Modules
-
Product
NI-9478, 50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module
779940-01
Digital Module
50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module - The NI‑9478 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. The NI‑9478 features programmable current limits, which provide customizable system protection that is ideal for solenoid and valve control applications. Each channel is compatible with signals from 5 V to 50 V and features isolation from channel‑to‑earth ground.
-
Product
PXI Hybrid Dual SPDT Coaxial Switch, DC to 26.5 GHz, Unterminated
M9155C
Switch Module
M9155C PXI Hybrid Dual SPDT Coaxial Switch, DC to 26.5 GHz, Unterminated
-
Product
Signal, Module, Receiver, TriPaddle, 90 Series, 256 Position
510104149
Receiver Module
Primary mating module 510108131. (May mate with other ITA modules, as well.)
-
Product
PXIe-6537, 32-Channel, 50 MHz, 200 MB/s PXI Digital I/O Module
779989-01
Digital I/O
32-Channel, 50 MHz, 200 MB/s PXI Digital I/O Module—The PXIe‑6537 can continuously stream data over the PXI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
Product
PXI 8-slot BRIC Multiplexer, 10-Channel, 80-Pole (7 Sub-cards)
40-570A-115
Multiplexer Module
The 40-570A-115 is a 10-channel, 80-pole High-Density Multiplexer and is part of our BRIC family. The 40-570A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
Product
PXI 3A Power MUX BRIC, 3-Channel, 48-Pole
40-571-003
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
PXI/PXIe High Density 2A Multiplexer, 1-Bank, 64-Channel, 2-Pole
40-614D-016
Multiplexer Module
The 40-614D-016 (PXI) and 42-614D-016 (PXIe) 1-bank, 64-channel, 2-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PMC Module
PMC-1553
PMC Module
Operating temperatureCommercial: 0 to +55 °COptional: -25°C to +80°C• Non-operating: -40°C to 85 °C• Airflow requirement: .5 CFM• Humidity: 5 to 90% (non-cond.)• Altitude: 0 to 10’000 ft
-
Product
FPD Tester Signal Module
A040209-05-04
Signal Module
A040209-05-04 is a MIPI signal module board and complies with the MIPI DSI v1.2 / MIPI D-PHY v1.1 signal specifications and standards. A040209-05-04 is used with the FPD Tester and can be applied to MIPI Display testing, providing MIPI Panel standard signal and other related controls.
-
Product
LXI Microwave Multiplexer, SP6T, 7-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-800-507
Multiplexer Module
Our 60-800-507 is a 7 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
LXI Microwave Multiplexer, SP4T, 14-Bank, 18GHz, 50Ω, SMA
60-803-114
Multiplexer Module
Our 60-803-114 is a 14 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 18GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
LXI High Voltage Switching - 1-Bank, 1-Pole, 48:1 Multiplexer Plugin Module
65-231-900
Multiplexer Module
The 65-231-900 plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
Blank, Module, Receiver/ITA, iCon and i1
510160100
Blank Module
Blank modules are used to help cover empty spaces created by unused module slots and help prevent debris entrance into the test rack.
-
Product
PXIe-2790, 6 GHz, Dual 2x1 PXI RF Multiplexer Switch Module
782576-01
Multiplexer Module
PXIe, 6 GHz, Dual 2x1 PXI RF Multiplexer Switch Module—The PXIe‑2790 can either switch or combine RF signals for multi-DUT cellular and wireless connectivity production test. It features high-performance solid-state relays that offer unique benefits such as an unlimited mechanical lifetime and fast switching time, as well as front-mounted SMA connectors that provide easy connection to your RF devices.
-
Product
PXI 2A Multiplexer 158-Channel 1-Pole
40-611-001
Multiplexer Module
The 40-611 Very High Density multiplexer module is available in 158-Channel 1-Pole or 79-Channel 2-Pole configurations. Both configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI 8x4 RF Matrix 300MHz 50 SMB With Loop-Thru
40-729-001-L
Matrix Switch Module
40-727/728/729 are RF Matrix Modules suitable for switching frequencies to 300MHz (50Ω version). The modules are available in either 50Ω or 75Ω versions with a choice of coaxial connectors. The 40-727/728/729 are designed designed to provide a simple and scalable bidirectional matrix to RF frequencies. They are intended for the easy construction of high performance bidirectional matrix switching systems.
-
Product
PXI 12-Slot BRIC Matrix, 1008x6 1-Pole (12 Sub-cards)
40-558-121-1008X6
Matrix Switch Module
The 40-558-121-1008x6 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PCI Resistor Card 2-Channel 1.5 Ohm To 2.04k Ohm With SPDT
50-293-122
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI 8-Slot BRIC Matrix, 2A 1-Pole 264x8, 6 Sub-cards
40-567A-106
Matrix Switch Module
The 40-567A-106 is a PXI 1-pole 264x8 matrix in BRIC8 format and is part of a range of high density matrix modules able to switch up to 2 A or 100VDC/70VAC. The 40-567A BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXIe Flexible Microwave Module, Dual SP6T Terminated 26.5 GHz, Single SPDT 26.5 GHz, 50 Ω, SMA
42-890-004
Switch Module
The 40-890 (PXI) and 42-890 (PXIe) range of PXI microwave modules allows users to specify the mix of relay types, frequencies and quantities based on the application requirements within the capabilities of the module driver card. Choose from the extensive relay selection already available in the Pickering microwave range to create a flexible solution.
-
Product
PXI 8 Slot BRIC Matrix, 2A 1-Pole 192x12, 6 Sub-cards
40-597A-106
Matrix Switch Module
The 40-597A-106 is a PXI 1-pole 192x12 matrix in BRIC8 format and is part of a range of high density matrix modules able to switch up to 2 A or 200 VDC/210 VAC. The 40-597A BRIC modules are available in 2, 4 or 8-slot sizes to suit most high performance PXI matrix requirements, constructed using high quality electro-mechanical relays for high switching confidence.
-
Product
PXI 12-Slot BRIC Matrix, 132x16 1-Pole (12 sub-cards)
40-562B-321-132X16
Matrix Switch Module
The 40-562B-321-132X16 is a high density BRIC12 matrix module with a size of 132x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Precision Resistor Module 4-Channel, 1.5 to 925
40-297-121
Programmable Resistor Module
This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI/PXIe RF Multiplexer, Single 16-Channel, 3GHz, 75Ω, MCX
40-835A-101
Multiplexer Module
The 40-835A-101 (PXI) and 42-835A-101 (PXIe) are single 75 Ohm 16-channel RF multiplexers in a single slot. It has been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The design of the 40/42-835A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
Intelligent ARINC Interface Module
M4K717
Interface Module
The M4K717 is an intelligent ARINC 717 interface module for the multiprotocol Excalibur 4000 family of carrier boards.The module supports two ARINC 717 receive channels and two transmit channels.In transmit mode, the module sends the four subframes from a pre-defined buffer in dual-port RAM.In receive mode, the module stores all subframes with status and Time Tag information appended to each subframe.The M4K717 comes complete with C-driver software library including the source code.
-
Product
PXI 10 Banks of 8 Channel 2 Pole MUX
40-615-022-10/8/2
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP6T, 50GHz, 50Ω, SMA-2.4
40-785C-551-E
Multiplexer Module
The 40-785C-551-E (PXI) and 42-785C-551-E (PXIe) are single SP6T 50GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 255 Ohm
50-294-013
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Single-Mode, 9/125 Fiber, SC/PC Connectors
42-852A-218
Multiplexer Module
The 40/42-852A-218 is a PXI/PXIe 8-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
Product
PXI 12-Slot BRIC Matrix, 99x16 2-Pole (9 sub-cards)
40-562B-322-99X16
Matrix Switch Module
The 40-562B-322-99X16 is a high density BRIC12 matrix module with a size of 99x16 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.





























