Isolated Digital Output Modules
-
Product
PXI 32 Channel Switch Simulation Module
40-480-221
Digital I/O
The 40-480 is designed to simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. It allows automotive I/O devices to be tested for correct operation under adverse conditions. The design includes protection circuits that ensure module damage cannot be caused by wiring faults or UUT failures. Each module can support up to 32 channels and is suitable for both 12V and 24V automotive applications.
-
Product
Computer On Modules
COM Express Basic
Computer on Module
COM Express Basic is the latest COM 125mm x 95mm form-factor, including Intel core i, Intel 6th Generation and Intel Atom processor. Because of wide range of processors, Intel core i, Intel 6th Generation and Intel Atom processors, COM Express can provides not only high-speed interfaces like HDMI/DisplayPort, PCI Express, SATA and USB 3.0 for volume data transportation, but also LVDS, PCI, and IDE for legacy applications.
-
Product
32-Ch DPST 2A-125VAC 24VDC Multiplexer
YAV904X8
Multiplexer Module
The YAV904X8 features 32 channels of DPST relays distributed in 4-banks. The module uses electro-mechanical relays allowing each channel to switch current up to 2A and voltage up to 125VAC.
-
Product
LXI Microwave Multiplexer, SP4T, 2-Bank, 50GHz, 50Ω, SMA-2.4
60-803-702
Multiplexer Module
Our 60-803-702 is a 2 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 180 MS/s on 2 Channels, 2 Single-Ended Inputs
DN2.447-02
Digitizer
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
LXI Microwave Multiplexer, SP4T, 13-Bank, 67GHz, 50Ω, SMA-1.85
60-803-813
Multiplexer Module
Our 60-803-813 is a 13 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
COM Express
Computer on Module
COM Express, defined by the PCI Industrial Computer Manufactures Group (PICMG), is the most successful Computer-On-Module (COM) standard in the embedded market today. COM Express employs a mezzanine-based approach, whereby an off-the-shelve module with two 220-pin board-to-board connectors, plugs into a custom, application-specific carrier board.
-
Product
Computer On Modules
COM Express Compact
Computer on Module
Advantech COM-Express Compact includes Intel core i, Intel 5th Generation, Intel atom processor, which are all designed with low power consumption processors. They perform the same functions and same pin definitions as the COM-Express Basic module but with smaller board dimensions of 95 x 95 mm. And COM Express Compact series provide from Intel core i, Intel 5th Generation, Intel atom processors, and is the best solution for mobile applications.
-
Product
LXI High Voltage Switching Multiplexer Plugin Module
65-231-900-HI
Multiplexer Module
The 65-231-900-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 50GHz, 50Ω, SMA-2.4
40-785C-451-TE
Multiplexer Module
The 40-785C-451-TE (PXI) and 42-785C-451-TE (PXIe) are single SP4T 50GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
4x (1 to 4) + 1x (4 to 1) 50 Ohm 2.5GHz Mux
YAV91500
Multiplexer Module
5x (1×4) Mux + 2x Pass trough30Vac/dc, 10W MaxMax current 500mACAN Control (or Ethernet with Ethernet to CAN Gateway)Drivers dll & VIs availableReflective
-
Product
PXI Quad 4 to 1 Mux 1GHz 75 Ohm SMB
40-749-751
Multiplexer Module
The 40-749 is a quad 4 to 1 RF MUX available in 50 Ohm or 75 Ohm versions occupying a single PXI slot. The module is available with SMB or SMA connectors for 50 Ohm versions or, 1.0/2.3 or Mini SMB connectors for 75 Ohm versions. Applications for the 40-749 include routing high frequency signals to and from oscilloscopes, analyzers, signal generators and synthesizers, telecoms tributary switching, video/audio switching and switching high frequency logic signals.
-
Product
NI-6585, 200 MHz, 32 LVDS-Channel Digital I/O Adapter Module for FlexRIO
781071-01
Digital I/O Adapter
200 MHz, 32 LVDS-Channel Digital I/O Adapter Module for FlexRIO—The NI-6585 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a digital instrument for interfacing with 32 low-voltage differential signaling (LVDS) digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6585 can operate at up to 200 MHz clock rates and includes support for common LVDS voltages.
-
Product
NI-9421, 24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module
NI-9421 / 779002-01
Digital Module
24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module - The NI‑9421 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels and has an LED indicating the state of that channel. The NI‑9421 offers isolation between the input channels and earth ground.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP10T, 22 GHz, 50 Ω, SMA, Terminated, Remote Mount, Failsafe
40-788-132-TE
Multiplexer Module
The 40-788-132-TE (PXI) and 42-788-132-TE (PXIe) are dual failsafe SP10T 22 GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
Product
PXI 2 Banks of 80 Channel 1 Pole MUX
40-615-022-2/80/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration. Connections are made via a front panel 200-pin connector.
-
Product
Octal 4 to 1 50 600MHz PXI RF Multiplexer
40-760-008
Multiplexer Module
This octal 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781774-02
Signal Module
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 6-Bank 18GHz SMA
60-802-206
Multiplexer Module
The 60-802-206 is a 4-channel, 6-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PCIe-5775, 12-Bit, 6.4 GS/s, 2-Channel PCI FlexRIO Digitizer Device
785593-01
FlexRio Digitizer
The PCIe-5775 is a PCI FlexRIO Digitizer Device that provides 6 GHz of AC-coupled analog bandwidth and 12 bits of resolution. You can operate the PCIe-5775 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. With a passband from 1 MHz to more than 6 GHz, the PCIe-5775 is ideal for high-bandwidth frequency domain applications, including radar prototyping, LIDAR, and communications.
-
Product
PXI 2A Multiplexer, 8-Bank, 4-Channel 4-Pole
40-614-005
Multiplexer Module
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
Product
LXI High Voltage Switching - 1-Bank, 1-Pole, 24:1 Multiplexer Plugin Module
65-231-902
Multiplexer Module
The 65-231-902 plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
EMX-75XX
Digital I/O
The EMX-75XX Series adds to AMETEK VTI Instruments' growing PXI Express (PXIe) Core Automated Test Equipment (ATE)TM family as a high-current, high-density digital input/output line of modules. Unlike many static I/O PXIe modules on the market today, the EMX-75XX Series can sink or source up to 300 mA on each channel. Delivering beyond just 2 V and 5 V, engineers can program the cards to support a wide range of voltages and more—on every channel, for both input and output.
-
Product
FPGA PXIe High-Performance Digital I/O Card
GX3700e
Digital I/O
The GX3700e is a user configurable, FPGA–based, 3U PXI Express card offering 160 digital I/O signals which can be configured for single-ended or differential interfaces. The card employs the Altera Stratix III FPGA, which can support SerDes data rates up to 1.2 Gb/s, digital I/O clock rates of 700 MHz, and features over 45,000 logic elements and 1.836 Kb of memory. The GX3700e is supplied with an integral expansion board providing access to the FPGA’s 160 I/Os. Alternatively, users can design their own custom expansion cards for specific applications - eliminating the need for additional external boards which are cumbersome and physically difficult to integrate into a test system. The design of the FPGA is done by using Altera’s free Quartus II Web Edition tool set. Once the user has compiled the FPGA design, the configuration file can be loaded directly into the FPGA or via an on-board EEPROM.
-
Product
Signal/Thermocouple, Module, Receiver, TriPaddle/ Thermocouple, 84/12 Position
510104261
Receiver Module
Signal/Thermocouple, Module, Receiver, TriPaddle/ Thermocouple, 84/12 Position
-
Product
PXI Single SP4T Multiplexer 18GHz 50 SMA
40-784A-121
Multiplexer Module
Pickering Interfaces’ range of 40-784A PXI Microwave Multiplexer Modules have a characteristic impedance of 50Ω and are capable of switching signals up to 40GHz. Available in single, dual or triple, SP6T or SP4T formats, they are suitable for constructing complex microwave switching networks and provide a range of switching configurations to suit most applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors
-
Product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 8-Channel, 2-Pole
40-739-004
Multiplexer Module
The 40-739-004 (PXI) and 42-739-004 (PXIe) are dual 8-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
Product
LXI 50Ω 6:1 Microwave Multiplexer 16-bank 40GHz SMA
60-800-416
Multiplexer Module
Our 60-800 Microwave Multiplexer range is suitable for switching 50 ohm signals up to 40GHz. With the capability of supporting up to 16 banks of 6 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA connectors.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP10T, 18 GHz, 50 Ω, SMA, Remote Mount, Failsafe
40-788-121-E
Multiplexer Module
The 40-788-121-E (PXI) and 42-788-121-E (PXIe) are single failsafe SP10T 18 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
Product
Extreme Rugged Cold Plate Mount System with Intel® Xeon® Processor and MIL-DTL-38999 Connectors
HPERC-KBL-MC
Processing Module
Inside the tiny footprint of ADLINK’s HPERC lives the power of Intel® Xeon® processor and optional GPGPU parallel processing engine based on a NVIDIA Quadro MXM module. Dual removable secure erase RAID-0 SSDs provide 12Gb/s throughput and security for deployment in hostile environments.
