Isolated Digital Output Modules
-
Product
90/120 GHz Dual Channel Optical Module
N1032B
Optical Module
The N1032B is a plug-in module for the DCA-X mainframe that includes two optical channels up to 120 GHz.
-
Product
Flex Socket Test Module
JT 2127/Flex Socket Test Module
Test Module
The JT 2127/Flex STM memory socket tester is a family of hardware adapters specifically designed for the testing of of PCB-mounted DIMM & SODIMM sockets using a JTAG/boundary-scan controller and supporting software. The testing of memory sockets has always been troublesome for test and production engineers using JTAG/boundary-scan systems. Even when it is possible to create memory writes/reads from a boundary-scan compliant access device on the UUT (Unit Under Test), the initialization process may fail leaving you with little diagnostics information. What’s more it can still be uncertain whether fault lays with the DIMM module itself or the socket. Using the new JT 2127-Flex system from JTAG Technologies you get pin-point diagnostics from a known-good test interface so you can be certain that your socket is soldered correctly.
-
Product
PXI Solid State Switch Module, 6xSPST, 30 A
40-183B-011
Switch Module
The 40-183B-011 has 6 high current SPST switches in two PXI chassis slots. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 30A of continuous current and switch up to 40V signals. The switch can sustain inrush currents in excess of 120A. AC or DC signals can be switched since the switch is polarity insensitive.
-
Product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781339-04
Signal Module
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP6T, 18GHz, 50Ω, SMA, Remote Mount
40-784B-023-E
Multiplexer Module
The 40-784B-023-E (PXI) and 42-784B-023-E (PXIe) are triple SP6T 18GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber, SC/PC Connectors, With Interlock
42-850A-214-M50-HI
Multiplexer Module
The 40/42-850A-214-M50-HI is a PXI/PXIe 4-channel multiplexer with SC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 5 GS/s on 2 Channels, 2.5 GS.s on 4 Channels, 1.25 GS.s on 8 Channels, 1.5 GHz Bandwidth
DN2.225-08
Digitizer
The digitizerNETBOX DN2.22x series allows recording of up to 8 channels with sampling rates of 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
SMARC Short Size Module with Intel® 6th Gen. Atom® x6000 Processors (formerly codename: Elkhart Lake)
LEC-EL
Computer on Module
The ADLINK LEC-EL is a SMARC module that supports Intel Atom® x6000 (x6425E, x6413E, x6211E, x6200FE, x6425RE) processors (formerly Elkhart Lake) with integrated Intel® UHD graphics and high speed interfaces. LEC-EL modules support up 8GB LPDDR4 memory, and are also available with rugged operating temperature range and low power envelope, making them a perfect match for mission critical fanless edge computing applications that require safety and reliability at all times.
-
Product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 4-Channel, 2-Pole
42-739-006
Multiplexer Module
The 40-739-006 (PXI) and 42-739-006 (PXIe) are dual 4-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
Product
LXI High Voltage Switching - 2-Bank, 1-Pole, 12:1 Multiplexer Plugin Module
65-231-904
Multiplexer Module
The 65-231-904 plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP10T, 18 GHz, 50 Ω, SMA, Terminated, Failsafe
40-788-121-T
Multiplexer Module
The 40-788-121-T (PXI) and 42-788-121-T (PXIe) are single failsafe SP10T 18 GHz microwave multiplexers with automatic termination of unused signals. The 40/42-788 range of multiplexers are available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel. Remote versions are also available which can support one or two multiplexers in a dual slot module.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 8-Bank 26.5GHz SMA
60-802-308
Multiplexer Module
The 60-802-308 is a 4-channel, 8-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
16/32 GSa/s Digitizer
M8131A
Digitizer
Wideband 32GSa/s Optical Data Interface (ODI) modular stream-able digitizer.
-
Product
PXI/PXIe RF Multiplexer, Dual 4-Channel, 3GHz, 50Ω, MCX
40-872A-102
Multiplexer Module
The 40-872A-102 (PXI) and 42-872A-102 (PXIe) are 50 Ohm 4 to 1 PXI RF multiplexers with 2 banks in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
LXI Microwave Multiplexer, SP4T, 14-Bank, 67GHz, 50Ω, SMA-1.85
60-803-814
Multiplexer Module
Our 60-803-814 is a 14 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-Purpose Digitizer - 125 MS/s on 12 Channels, 80 MS/s on 24 Channels, 24 Single-Ended Inputs, 12 True Differential Inputs
DN6.596-24
Digitizer
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
PXI 3A Power MUX BRIC, 4-Channel, 12-Pole
40-571-301
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
PXI High Density MUX BRIC, 24-Chan, 20-Pole
40-570-313
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
LXI Microwave Multiplexer, SP4T, 15-Bank, 67GHz, 50Ω, SMA-1.85
60-803-815
Multiplexer Module
Our 60-803-815 is a 15 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI 3A Power MUX BRIC, 4-Channel, 48-Pole
40-571-004
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
PXI Solid State Multiplexer, 5 Amp, Single 48-Channel, 1-Pole
40-652A-001
Multiplexer Module
The 40-652-001 is a 48-channel, 1-pole MUX and is part of our range of multiplexers uses solid state relays with high tolerance to surge currents and hot switching events. These multiplexers provides an isolation relay in the common to minimize capacitive loading when expanding the multiplexer across multiple modules. The 40-652 can sustain 30A for 300µs on hot or cold switching.
-
Product
PXI 2A Multiplexer 158-Channel 1-Pole
40-611-001
Multiplexer Module
The 40-611 Very High Density multiplexer module is available in 158-Channel 1-Pole or 79-Channel 2-Pole configurations. Both configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
Switch Modules - 32 Single Pole Relays Arranged as a 16x2 Matrix
JX32/AB-1
Switch Module
This module has 32 single pole relays arranged as a 16x2 matrix as shown in the figure to the left. The matrix may be operated and wired individually for up to 16 16x2's per chassis, or jumpered to the backplane to form up to a 256x2 matrix. It is available with Type S or M reed relays for high speed, long life application.
-
Product
Combo Unit, 7.5 Digit Digital Multimeter (DMM) with 10-Bit 1GHz Digitizer in a Single VXI Slot
6084A
Digitizer
Increases test system performance and density with this combo unit, which packages a 7.5 digit Digital Multimeter (DMM) together with a 10-bit, 1 GHz Digitizer into a single VXI slot.Replaces the Wavetek 1362 DMM, Analogic DBS Series, and Agilent VXI DigitizersDigitizer with 4 Inputs, 10-bits, 1 GHz, up to 4 GS/s and Ranges up to 500V DMM with 7.5 Digits for DC Volts, Current and Ohms with AC Volts up to 1 MHzIVI-COM Drivers and Soft Front Panels ProvidedMore Dynamic Range (by 20 dB for DMM and 12 dB for Digitizer) for Better Legacy Range Mapping
-
Product
PXI 8-slot BRIC Power Multiplexer, 32-Channel, 6-Pole (6 Sub-cards)
40-571A-404
Multiplexer Module
The 40-571A-404 is a 32-channel, 6-pole 3 Amp Power Multiplexer and is part of our BRIC family. The 40-571A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 50 GHz, 50 Ω, SMA-2.4, Failsafe
42-785C-451
Multiplexer Module
The 40-785C-451 (PXI) and 42-785C-451 (PXIe) are single failsafe SP4T 50 GHz unterminated microwave multiplexers. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
PXI/PXIe Microwave Transfer Switch, Single, 18 GHz, 50 Ω, SMA, Failsafe, Remote Mount
42-782B-521-E
Switch Module
The 40-782B-521-E (PXI) and 42-782B-521-E (PXIe) single failsafe transfer switches with remotely mounted relays are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 18 GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
Product
PXI Monitored Multiplexer, Single 64-Channel, 1-Pole
40-619-301
Multiplexer Module
The 40-619-301 is a high density PXI 2 A multiplexer module in single 64-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC.
-
Product
COM Express Basic Size Type 7 Module with Intel® Xeon® D SoC and 4 SODIMMs
Express-BD74
Computer on Module
- 4 SO-DIMMs, up to 128GB dual channel DDR4 at 1866/2133/2400MHz ECC (dependent on SoC SKU)- Intel® Xeon® D SoC (up to 16 cores)- Two 10G Ethernet and NC-SI support- Up to 32 PCIe lanes (24x Gen3, 8x Gen2)- GbE, two SATA 6 Gb/s, four USB 3.0/2.0- Supports Smart Embedded Management Agent (SEMA®) functions
-
Product
NI-9266 , 8-Channel C Series Current Output Module
785046-01
Current Output Module
8-Channel C Series Current Output Module - The NI‑9266 is ideal for interfacing and controlling industrial current-driven actuators. The module has built-in open-loop detection, which generates an interrupt in software when an open loop is detected as well as zeroing outputs to ensure safety and avoid driving actuators at system power on. The NI‑9266 includes channel‑to‑earth ground isolation for safety and noise immunity.
