Mil-Std-1553
Interface Standard for Digital Time Division Command/Response Multiplex Data Bus
See Also: MIL-STD, 1553, Mil-Std-1760
-
Product
Combination Module: 2 Ch. MIL-STD-1553 & 12 Ch. Discrete I/O
CM8
-
The CM8 module is a combination of NAI's MIL-STD-1553B module, FTB, and Enhanced Discrete I/O module, DT4. The CM8 offers twelve channels of discrete I/O and two channels of MIL-STD-1553B communications. The twelve discrete I/O channels are programmable as either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3-60 VCC source. The discrete I/O channels also provide additional functionality modes such as Pulse Width Modulation (PWM) output mode and Pattern Generator output mode. The two MIL-STD-1553B communications channels feature a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
Software
LV-1553
-
The LV-1553 software is the interface to operate Abaco Systems' MIL-STD-1553 USB, XMC, PCIe, PCI, cPCI, ExpressCard, PCMCIA, Q104-Plus, AMC and VME boards with National Instruments’ LabVIEW graphical programming environment.
-
Product
Redundant Strap down INS ATE Test Station
-
Redundant Strap down Inertial Navigation System (RESINS) checkout test station comprises of cPCI chassis with various functional I/O modules like ADC, DAC, DIO, VFC, Relay matrix, MIL 1553, GPIB, Serial communication interfaces and Custom Built System interface adaptor.
-
Product
Single UTMC BC/RT/M or SUMMIT 1553 Controller
PCI-1553 PLX
Controller
The PCI-1553-X uses a single UTMC’s Sµmmit or BCRTM communication device as its 1553 bus controller, or remote terminal, or monitor terminal. The single controller has two redundant channels. This controller accesses 64Kx16 word of external memory and has external for both channel A and B. The 3U PCI board has on-board transformersfor both channels.
-
Product
PC Card
I/O Mezzanine modules
-
MAX Technologies’ IPM mezzanine modules are available for MIL-STD-1553, ARINC 429, ARINC 561, ARINC 568, ARINC 629, ARINC 708, ARINC 717, SERIAL ASYNC RS-232/422/485, CSDB, ASCB, HDLC/SDLC, Pulse/Frequency generator, Analog, Single and Differential Discrete I/O and more.
-
Product
MIL-STD-1553
-
The Avionic Interface MIL-STD-1553 products offer solutions for flight test instrumentation (FTI), for data acquisition, for protocol analysis, embedded IP solutions and COTS applications.
-
Product
vibration test system
-
Labtone Test Equipment Co., LTD
Labtone EV series of electrodynamic shaker vibration test System simulate the vibration environment under the laboratory condition, and test the impact strength as well as reliability of various vibration test applications.Labtone EV series of electromagnetic vibration testing system simulate the vibration environment under the laboratory condition, and test the impact strength as well as reliability of various vibration test applications. In the laboratory, with the aid of vibration testing system, simulations of reproduction of sinusoidal, random, resonant search and dwell, classical shock and road models, etc. can be achieved. It is essential for product quality assurance, new product research and development.Labtone EV series of electromagnetic vibration testing system is specially designed to meet the need for long time operation. Vertical and horizontal vibrations can be achieved by the installation of vibration resistant base. The standard platform is equipped with high efficiency airbag shock isolation device, so that the vibration transmitted to the building can be minimized. There is no need for additional foundation in most of the cases.A complete set of vibration testing system is composed of shaker, power amplifier and vibration measuring control system, in accordance with the relevant national and international standards (such as: MIL-STD, DIN, ISO, ASTM, IEC, ISTA, GB, GJB, JIS, BS, etc.) to provide technical support for establishing product quality inspection.
-
Product
Aerospace And Defense Software (3000A/T/G X-Series)
D3000AERB
-
MIL-STD 1553 and ARINC 429 triggering and analysis for the InfiniiVision 3000A, 3000T, 3000G X-Series oscilloscopes, along with mask testing, advanced math, video analysis, and more.
-
Product
Micro Coax, Contact, ITA, RG316
610141101
Coax Contact (ITA)
Primary mating contact 610140101. (May mate with other Receiver contacts, as well.)Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 50µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC – 3 GHzVSWR 1.22 @ 3 GHzInsertion Loss – √f(GHz) x .06 dBDWV 800 V RMSContact Resistance 6 mOhms center/4 mOhms outer Cable Specifications RG316Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
Product
Intelligent Interface Card
IIB-1553-PC104+
-
The IIB-1553-PC104+ is an intelligent interface card giving full MIL-STD-1553 test, simulation and bus analysis capability on the PC104+ bus, providing 1553A, 1553B, McAir and STANAG 3838 variants in a single card. The IIB-1553-PC104+ supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a variable amplitude dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
Product
Linear Bench or Rack Mount Power Supplies Programmable, Local Control, Ultra Low Ripple/Noise
Series PTR
-
SERIES PTR are operationally programmable power modules that can be programmed to any level within their rated range and fully loaded at any output setting. These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
-
Product
USB 1553 and ARINC Appliance
USB-MA4
USB Interface
The industry’s first USB 3.0 SuperSpeed Multi-channel MIL-STD-1553 and/or ARINC-429 appliance!1-2 1553 Dual Redundant Channelsand/or 8 ARINC-429 Channels (4 RX/TX and 4 RX)Supports ARINC-717 (shared with 429 channels)
-
Product
500W to 1500W - Single Output
LZSA Series
-
*Five year warranty*-40°C to +71°C Operation*MIL-STD-810E Vibration / Shock*Input transient protected*UL508, SEMI F47, Factory Mutual (Cl 1, Div 2)*Rugged design with conformal coating*Superior thermal design
-
Product
Coax, Contact, Receiver, 75 Ohm HD, sm59/U Belden 1855A, 3 GHz
610102133
Coax Contact (Receiver)
Primary mating contact 610102132. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Female & Male Shield – BrassCenter Contact – BeCuContact Plating Center Conductor Shield – 30µ” Au over 100µ” NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 2.0 lbs max [0.91 kg]Electrical SpecificationsCharacteristic Impedance 75 ΩFrequency Range DC to 3 GHzVSWR ≤ 2.26 @ 3 GHzInsertion Loss -0.86 dB MaxDWV 1500 VDC min.Contact Resistance 5 mΩ center/ 3 mΩ outer Cable Specifications sm59/U Belden 1855AEnvironmental SpecificationsOperating Temperature -55°C to +125°CVibration MIL-STD 1344, Method 2005, Test Condition 4Shock MIL-STD 1344, Method 2004, Test Condition EInsulation Resistance 1000 MΩ min.
-
Product
HS1760/MIL-STD-1760E XMC Network Interface Controller
XMC-1760-NIC-FP
-
Avionics Interface Technologies
Configuration Variants available: XMC-HS1760-NCNT: One NC Node and One NT Node, XMC-HS1760-NCNC: Two NC Nodes, XMC-HS1760-NTNT: Two NT Nodes - SAE AS5653-Compliant Network Controller/Network Terminal NIC - Unsolicited data path for handling Fibre Channel link service or non‐FC-AE‐1553 traffic - Supports DMA for high speed streaming of data75 Ohm single‐ended or 150 Ohm Differential coax interface – TNC connectors - Each port supports 1.0625 Gbps speed - ANSI C API interface for both NC and NT - Device driver support: Windows, Linux, & VxWorks - Quad (4) port board available on request
-
Product
Avionics Data Bus Tester
Distributed CORVUS
-
Distributed CORVUS works in conjunction with CORVUS-300 to isolate bus anomalies and fault resolution. The Transmit unit, C-9235-TX, sends 1553 like data pattern through a bus stub and coupler to the Receive unit, C-9235-RX, on another stub. This will measure insertion loss, possible bit errors and correct polarity. The Receive unit can also be used to give a digital scope representation of the active data bus showing signal quality and peak to peak amplitude.
-
Product
Bus Interface
IP-1553
-
MIL-STD-1553 is a versatile standardized bus interface. MIL-STD-1553 is robust featuring Manchester encoding and enough voltage swing to provide excellent noise immunity and reasonable throughput rates.
-
Product
Type 12R2, 10U, 19" Rackmount, MIL-Rugged, Vertical
12R2-10U-V
-
The 10U, 12R2 is designed to meet the harsh environment of shipboard, airborne, and ground mobile applications per MIL-STDs. Shock isolated versions are designed to attenuate 25G shock inputs to the chassis to less than 10Gs at the card cage.
-
Product
Transient Generators
9354-1 & 9354-2
-
The Model 9354-1 & 9354-2 Transient Generators were especially designed for the performance of a variety of pulse susceptibility tests on subsystems and/or equipment, in accordance with MIL-STD-461D and E, method CS116; also capable of testing for RTCA DO160D, section 22; MIL-STD-461C, methods CS10 and CS11.
-
Product
Multi-Protocol Board
EXC-8000cPCI
-
The board supports up to 6 modules, and each module represents an independent test and simulation device. Most modules are based on existing Excalibur products such as the 1553 Px family and the ARINC429 RxTx.
-
Product
Fibre Channel Simulyzer™ Products
-
Avionics Interface Technologies
Our Fibre Channel products support most popular avionics Upper Layer protocols including FC-AE-ASM, FC-AE-1553, FC-AE-RDMA and FC-AE-AV. All AIT Fibre Channel modules utilize multiple processors with large onboard RAM. An onboard processor runs the driver software, minimizing host CPU interaction, enabling autonomous operation with minimal interaction during time-critical applications.The Fibre Channel products use our Simulyzer™ technology that enables the hardware to simultaneously perform Fibre Channel data generation and Fibre Channel monitoring on the same physical board. The Fibre Channel test products include full-function device driver software for the most popular operating systems, an application interface supporting development environments, as well as a comprehensive set of source code examples.
-
Product
USB 2.0 SmartCable For MIL-STD-1553 Test And Simulation
ASC1553
-
The ASC1553 (AIM SmartCable) USB module offers full function test, simulation, monitoring and recording for MIL-STD-1553B applications implemented in an ultra compact form factor.
-
Product
CompactPCI Interface Card
CPCIC-1553/PXI
Interface Card
The CPCIC-1553/PXI Interface Card and AltaAPI Represent the Latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology with Multi-Layer Software. Our Card and Software Packages are Designed for Fast, Portable Integrations. The CPCIC-1553 is the Only Commercial Off the Shelf (COTS) Card that Passes and Executes the SAE AS4111/4112 Protocol Tests.
-
Product
MIL-STD-1553 Protocol
-
For demanding application needs, our 1553 product line combines high-speed encoding/decoding, intelligent protocol processing and advanced board-level functionality.
-
Product
Coax, Contact, ITA, 20 GHz, RG 223, Crimp, 90 Series Modules only
610102117
Coax Contact (ITA)
Primary mating contact 610102116. (May mate with other ITA contacts, as well.)20 GHz coax contacts have an impedance of 50 Ohms and a current rating of 5 amps.It is recommended to use SF142 to achieve 20 GHz and RG223 to achieve 12 GHz.Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating 30µ" Au over 100µ" NiContact Termination Shield – Crimp/ClampInsulator PTFEMating Force 3.0 lbs max [1.36 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 20 GHzVSWR 1.15 + .01 (f) GHz w/ RG142 (8 GHz)1.15 + .01 (f) GHz w/ SF142 (20 GHz)Insertion Loss .06 x√f(GHz) dBDWV 800 V RMS Shield to center contact1000 V RMSContact Resistance 5 mOhms center/ 3 mOhms outer Cable Specifications RG 223 Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
Product
Attitude And Heading Reference Systems
AHRS
-
Beginning in 2001, Inertial Labs began manufacturing its MEMS-based, IP-67 sealed, MIL-STD-810G qualified, multiple interfaces and COM ports Attitude and Heading Reference System in response to the need for an inclusive and price competitive Antenna Pointing, Aiming, and Stabilizing applications. Each INS contains an Inertial Labs-developed tactical or industrial-grade inertial measurement unit (IMU) and an Inertial Labs-manufactured high-precision Fluxgate magnetometer.
-
Product
Constant Acceleration Tester-Arm Type
KRD31 series
-
KRD31 series constant acceleration tester are used to test articles under extreme acceleration conditions based on standard like MIL-STD-810F, MIL-STD-202 and IEC68-2-7. It is most suitable for testing electronic components or devices. Under high g effect on microcircuits, to check adaptability and reliability of wiring and the internal structures. It may expose mechanical and structural defects that are not found with vibration and shock tests.
-
Product
Flight-Certifiable SBC
SBC314C
-
The SBC314C flight-certifiable single board computer is engineered in accordance with DO-178C and DO-254 and is available with supporting artifacts. It delivers great and proven performance thanks to the Power Architecture T2081 processor, and its diverse I/O set brings high functionality to the small form factor. The integrated XMC site allows even more connectivity, including high-density MIL-STD-1553 and ARINC 429 data bus communications as well as avionics discrete I/O through our RAR15CX flight-certifiable mezzanine.
-
Product
Longbow Launcher / LEA Test Set
TS-201B
-
The TS-201 is a state-of-the-art I-Level and Depot level test set for MIL-STD-1760 and legacy armament systems including launchers and bomb racks.
-
Product
PCI Generic Carrier Cardfor PMC (PCIbus Mezzanine Card) Modules
ACP-1
-
PCI generic carrier card for PMC (PCIbus mezzanine card) with 1 PMC slot. Modular solution combines any AIM PMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party PMC module.
