PXI DAQ
-
product
PXI 10W Programmable Resistor Module, 1-Channel, 1Ω to 31.5Ω
40-253-110
The 40-253-110 is a programmable resistor module with 1 channel which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
TB-2630B , Screw Terminal, Ribbon, PXI Module Multiplexer Terminal Block
781687-01
The TB-2630B provides the necessary routing to configure the PXI-2630B PXI Multiplexer Switch Module as a single, dual, or quad 1-, 2, or 4-wire multiplexer. You can directly connect the TB-2630B to the front panel I/O connectors of the PXI-2630B. The NI TB-2630B features ribbon cable headers to connect signals to the PXI Multiplexer Switch Module as well as screw terminals for trigger input and trigger output signals.
-
product
Wideband Amplifier PXI Card
GX1222
The GX1222 is a 3U single-slot, PXI-based wideband power amplifier used for signal amplification purposes. Offering excellent fidelity, the GX1222 amplifies signals from DC to over 20 MHz with a fixed gain of x10. Custom gains are also available without compromising signal purity and amplifier performance.
-
product
PXI 2 Amp Multiplexer, 4-Channel, 7-Bank, 2-Pole
40-655A-002
The 40-655A-002 is a 2 Amp multiplexer, specifically designed for switching POTS, ISDN or xDSL telephony signals, contains seven separate 4-channel multiplexers, 2-pole switching and is suitable for switching signals to 220VDC/125VAC.
-
product
PXI 8 Slot BRIC 220x8 1-Pole (10 sub-cards)
40-562A-121-220X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI 4 Slot BRIC Solid State 64x8 1-Pole (2 sub-cards)
40-563A-021-64X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
Fixed Wavelength CW Laser Source (FP) - PXI
Laser 1100 Series
The Laser-1102 is a Continuous Wave (CW) laser source offering high power 850 nm output into multimode fiber with stable output power operation.
-
product
Single 32x2 1-Pole High-Density PXI Matrix Module
40-520-502
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
product
PXI 12-Slot BRIC Matrix, 640x8 1-Pole (10 sub-cards)
40-558-121-640X8
The 40-558-121-640x8 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXI Single 24x8 Matrix, 2 Pole Switching
40-521-022
Typical applications for this high density matrix include signal routing in Functional ATE and data acquisitionsystems. These PXI matrix cards are constructed using high reliability rutheniumelectro-plated reed relays, offering >10e8 operations to give maximum switchingconfidence with long life and stable contact resistance. Larger matrices may be constructed by Daisy Chaining the common signals from multiple PXI modules. For example, 7 PXI modules will form a 168x8 Matrix, a total of 1344 crosspoints in a 7-slot PXI Chassis. All 40-521 series modules are fitted with reed relays (ruthenium sputtered type), these offer very long life with good low level switching performance and excellent contact resistance stability.Spare Reed Relays are built onto the circuit board to facilitate easy maintenance with minimum downtime.
-
product
PXI Precision Resistor Module 4-Channel, 1.5 to 3.55k
40-297-123
.This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI Digital I/O Module With Power Distribution - Without DC-DC Converter
40-228-002
The 40-228 provides 32 channels of digital input and 32 channels of digital output, together with switched +12V, +5V, +3.3V and -12V supply outputs derived from the PXI backplane. The module is available fitted with a DC-DC converter (40-228-001) which provides an additional -5V supply ouput. Alternatively the module can be supplied with an industry standard footprint for a DC-DC converter (40-228-002) allowing the user to fit one of their own specification if required. The 40-228 includes a breadboard area that allows users to add their own circuitry to the module.
-
product
PXI 8-Slot BRIC Matrix, 20x32 1-Pole (4 sub-cards)
40-562B-121-20X32
The 40-562B-121-20X32 is a high density BRIC8 matrix module with a size of 20x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
PXI 5W Programmable Resistor Module, 1-Channel, 2Ω to 6.97kΩ
40-252-130
The 40-252-130 is a programmable resistor module with 1 channel which can be set between 2Ω and 6.97kΩ with 0.125Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI Interface Module, AIT MIL-STD 1553
M3406A
Interface to the LRU in avionics test solution Up to four channel MIL-STD-1553 bus interface with full error injection and detection Concurrent Bus Controller, multiple Remote Terminals (31), and Bus Monitor operation capabilities Data capture filtering, 100% bus recording, and physical bus replay Variable output voltage signal and software selectable bus coupling modes 10 high voltage (up to 30 V) programmable DIO lines PXI trigger generation on 1553 bus events
-
product
PXI 8 Slot BRIC 230x8 1-Pole Dual Analog Bus (5 sub-cards)
40-560A-121-230X8-M
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI Power Supply
A PXI power supply provides the required power for a test application or additional devices. A constant output voltage is generated from the stabilized voltage of the PXI chassis.
-
product
PXI Multiplexer Single 24 Ch 2 Pole
40-632-021-24/2
This series of general purpose multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 68-pin connector. Available reed relay formats are 1-pole, 2-pole, 4-pole and 1-pole screened.
-
product
PXI Semiconductor/IC Test System
A high-density 100MHz PXIe digital IO card designed for characterizing, validating, and testing a variety of digital and mixed-signal ICs. Each IO card consists of a Sequencer Pattern Generator (SQPG) and 32 channels of full ATE-like features. The 33010 IO card is expandable up to 256 channels. Some unique features of the 33010 include an on-board SQPG, per pin timing/levels/ PMU/TFMU, multiple time domains, and multithreaded testing for complex IC testing. Each channel is also equipped with 64M vector memory, 16 timing sets with on-the-fly timing change, and per pin timing and frequency measurements up to 400 MHz.
-
product
ARINC 429 Test And Simulation PXI Module
PXI-C429
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
PXI 8 Slot BRIC Solid State 320x8 1-Pole (10 sub-cards)
40-563A-121-320X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI 8 Slot BRIC 198x8 1-Pole (9 sub-cards)
40-562A-121-198X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
PXI 12-Slot BRIC Matrix, 64x16 1-Pole (2 sub-cards)
40-558-121-64X16
The 40-558-121-64x16 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXI 8-Slot BRIC Matrix, 528x4 1-Pole (12 sub-cards)
40-562B-121-528X4
The 40-562B-121-528X4 is a high density BRIC8 matrix module with a size of 528x4 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
product
PXI Fault Insertion Switch, 7-Channel, One Fault Bus, 20 A, Hardware Interlock
40-194A-001-HI
The 40-194A-001 is a 7-Channel PXI Fault Insertion switch with hardware interlock and one fault bus, designed for the simulation of fault conditions in automotive systems. As well as high current handling of 20A, very low currents can also be switched.
-
product
4-Slot BRIC, 84x12, 1 Pole, PXI Matrix (2 Sub-cards)
40-559-401-84x12
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXI 5W Programmable Resistor Module, 2-Channel, 2Ω to 13.6Ω
40-252-031
The 40-252-031 is a programmable resistor module with 2 channels which can be set between 2Ω and 13,6kΩ with 0.25Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI Strain Gauge Simulator Module 2-Channel, 2K
40-265-302
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 2kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
PXI 2-Slot BRIC Matrix, 192x8, 1 Pole (3 Sub-cards)
40-558-201-192x8
The 40-558-201-192x8 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
product
PXI 17 x SPDT RF Switch 1.2GHz 50 SMB Connectors
40-754-117
The 40-754 is a 50Ω High Density RF switch available with 17 or 9 SPDT relays in a single PXI module. The 40-754 is available with two connector options; an SMB connector that provides a frequency range of 1.2GHz (useable to 1.8GHz) occupying two PXI slots, or an MS-M RF multiway connector which limits the bandwidth to 500MHz but offers a high density solution occupying one PXI slot. The RF switch design is identical in each case.


























