Level
high or low along a bead it's a measure referenced.
See Also: Liquid Level, Signal Level Meters, Level Transmitters, Depot Level Test
-
product
PCIe Adapters
Teledyne LeCroy offers a broad spectrum of PCI Express protocol analyzer platforms (Summit T516, Summit T54, Summit M5x, Summit™ T416, Summit T48, Summit™ T3-16, Summit T3-8, Summit T34, Summit T28, and Summit T24). The Summit T516, T54 and M5x are Teledyne LeCroy’s leading edge products supporting PCIe 5.0 and CXL specifications. The Summit T416, T48, T34, T3-16 and T3-16 are Teledyne LeCroys midrange protocol analyzers. These protocol analyzers are at the forefront of SSD and computer storage analysis, test and compliance. The Summit T28 and T24 are entry level protocol analysis tools for development and test at PCIe 2.0.
-
product
LCR Meter
ST5C Colibri
*Built-in direct LCR probe*Convenient one-hand operation*Ideal for Surface Mount Devices*Automated component identification*Automated test range selection*Manual C, R, L and ESR modes*Manual test frequency overrides*Test signal level 0.5 Vrms*Portable and ergonomic design*OLED Display*Built-in Li-Ion battery
-
product
Short Buddy® Audible Trouble Shooter
230
Short Buddy helps you find the short! This unique tool connects at the fuse panel and becomes in series with the test circuit. A system of audible beeps helps you find the problem and permit hands free troubleshooting. Have a dead short? Short Buddy gives you continuous re-set/re-power capability, a real time saver. While you push, pull, tug and grab wires, Short Buddy is always watching the current level. If your tug causes the dead short again, Short Buddy opens the circuit for 10 seconds, then re-applies power to the circuit. Re-powering the circuit can also be done manually.
-
product
High-Performance USB-Controlled PLL Synthesizers
Rugged, SMA-connectorized designs that support a USB 2.0 interface with a PC supplying DC power and GUI command control. They cover a broad range of frequency bands from 25 MHz to 27 GHz. These USB-Controlled PLL Synthesizers deliver output attenuation that is adjustable up to 50 dB in 1 dB steps and high output power levels ranging from +10 dBm to +19 dBm typical. Phase noise is as low as -108 dBc/Hz at 100 MHz offset and phase locked speed is 1 msec typical.
-
product
Preconditioning
Preconditioning is performed prior to package level reliability testing to simulate the effects of board assembly on non-hermetic devices where moisture may have been absorbed during normal storage. The subsequent exposure to high temperature during infra reflow assembly can cause internal damage such as “pop corning” and delamination.
-
product
Electronic DC Load, 500V, 16A, 400W
LDH400 Series
Versatile solution for direct testing of dc power sources and PFCsConstant current, resistance, conductance and power modesWide voltage and current range, 10 to 500V and 0 to 16A400 watts continuous dissipation at 28°C (360W at 40°C)High resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminalsLoad inputs rated to CAT II (300V)Full bus control via USB, RS232 and LXI compliant LAN interfacesGPIB Option
-
product
PXI 4 Slot BRIC 90x16 1-Pole (6 sub-cards)
40-561A-021-90X16
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
Dual MAX31865 PT-100 RTD to Digital Breakout
SEN-30202-PT100
Dual channel breakout board for the MAX31865 RTD-to-Digital converter from Maxim. Two breakout hardware configurations are available standard, designed to interface with either the PT100 or PT1000 platinum RTDs. For non-standard applications, including thermistors, custom hardware configurations can be accommodated. Contact Technical Support for more information. RTD devices may be wired in 2, 3 or 4-wire configurations using the 4-pin screw terminal input. The MAX31865 breakout is interfaced via 3 or 4-wire SPI with a data-ready output for specific operating modes. An LDO and a high-speed level shifter are included to allow interfacing with microcontroller devices between 3.0V and 5V (all Arduinos, Raspberry PI, etc) without sacrificing device performance.
-
product
Air Data Computer (ADC) Tester
MS 1122
The ADC tester is used in 2nd line maintenance is to check the functionality of ADC. This unit is a rugged customized hardware based on full functionality test of ADC. The Air Data Computer (ADC) Tester is a fully automated GO/NOGO tester with full functional testing in 2nd line maintenance. This tester is to test ADC at unit level and identify faulty Shop Replaceable Unit (SRU). This tester is also used to carry out PI checks on ADC before clear them for installation on aircraft. ADC Interface board designed to test full functionality of ADC. The Air Data Computer (ADC) test equipment shall be used for testing ADC of Tejas Aircraft. ADC test equipment shall verify the functionality against specifications during second line maintenance and pre-installation on the aircraft.
-
product
Moisture Analyzer
2850
Establishing a new standard for clean gas moisture analyzers, the 2850 provides exceptional performance, with virtually no interferences, multi-gas compatibility, and on-board measurement verification. The 2850 uses the most accurate trace moisture measurement technology available to deliver an ultrafast response to both increasing and decreasing moisture levels.
-
product
Low PIM Coaxial Switch, DC to 20 GHz, Matrix
87406Q
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87406Q is a low PIM matrix coaxial switch, operating from DC to 20 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency and ultimately maximizes test throughput.
-
product
Limit Controller
1401+
The 1401+ limit controller is a member of the P series family. The instrument provides a latched relay output which is activated when process value either exceeds or falls below the a pre-set limit level, providing a fail-safe cut off which has to then be reset before the process can continue.
-
product
Oscilloscope
When the Generator is active, the actual output levels are controlled by the Volume/dB dialog (F9 key, or button on the Generator Control dialog), but the screen display remains full-scale because it shows the digital signal as generated, before conversion to analog and attenuation by the output mixer volume controls. (The digital waveform size is set by the Generator Level controls for the active streams on each channel.)
-
product
Sound Level Meter
SM-2
Monacor International GmbH & Co.
Sound level meter (class 2), one-hand operation. Electret microphone capsule. Max hold and data hold function. A and C rating, slow and fast. Additional output for DC/˜V via 3.5 mm jack. Supplied with a practical nylon carrying bag.
-
product
Chemiluminescence NO/NO2/NOX Analyzer
Model T200
Teledyne Advanced Pollution Instrumentation
The Model T200 NO/NO2/NOx analyzer uses the proven chemiluminescence detection principle, coupled with state-of-the-art electronics to allow accurate and dependable low level measurements for use as an ambient analyzer or dilution CEMS monitor.A unique AutoZero feature provides superb stability by continuously correcting for zero drift, while advanced Adaptive Filtering allows the analyzer to optimize performance under changing conditions. The Model T200 includes a permeation inlet dryer for ozone generation to provide excellent reliability with no periodic replacement required. A catalytic exhaust ozone scrubber is standard for maximum safety and pump life.
-
product
Continuous Level Measurement
Drexelbrook manufactures a full range of continuous level measurement instruments, providing the highest level of performance for liquids, slurries and bulk solids applications. With a wide variety of technology options, Drexelbrook is uniquely qualified to properly evaluate and recommend the very best solution for your application.
-
product
HVAC/R Environmental Meter
FLIR EM54
The FLIR EM54 is ideal for inspecting and troubleshooting HVAC/R ducting systems within residential, commercial, and industrial facilities. This meter can help you verify that duct inlets and outlets have the specified volumetric flow – a prerequisite to an efficient functional system. Featuring humidity, wet bulb, and dew point functions, the EM54 can measure deviations from proper relative humidity levels. Plus, the included Type-K contact temperature probe is useful to check electric motors and thermal equipment components for proper operating temperatures.
-
product
Materials Measurement
Our VNAs are used for a variety of materials measurement applications. From NASA estimating fuel levels in the fuel tank with 1-Port reflectometers to Compact and Cobalt analyzers incorporated into portable, table-top free-space measurement systems that take materials RF measurement out of the lab and into the field or manufacturing environment to measuring moisture and sugar content in crops, liquid level in bottles of soft drinks and other food quality parameters using microwave sensor systems.
-
product
Y/t Recorder Software Module
Metra Mess- und Frequenztechnik in Radebeul e.K.
*Time graph display*Level display of vibration acceleration*VM-PLOT+ also for velocity and displacement*RMS, positive, negative and unsigned peak values, slow changing instantaneous value*Two time axes for clock time and time since start*Up to four signals per window*One VM-Plot license can be operated simultaneously up to four times with different settings *External Messengers*Offline measurement
-
product
PCIe-6536B, 32-Channel, 25 MHz, 100 MB/s Digital I/O Device
782630-01
The PCIe-6536 can continuously stream data over the PCI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
product
Power Supplies
NW-650B
Experience our new NW-series of power supplies. The NW-series can power your system from 450 to 650 watts. It offers a cooling system with a fan size of 120mm with automatic settings, so you no longer have to worry about high or low settings and if your fan is spinning too slow or too fast. The NW-series will adjust itself according to the necessary heat dissipation level. It is dual PCI-E ready for better graphics capabilities (at 650W). Painted in black, the NW series works and looks great.
-
product
PXI 8 Slot BRIC 150x8 1-Pole (5 sub cards)
40-561A-121-150X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
Hand Held Instrumentation
A selection of hand held instruments for many applications including a large range of digital thermometers, light level meter, stroboscope and a range of great value handheld sensors.
-
product
CL PX4 Dual Frame Grabber
Xcelera-CL PX4 Dual
Building on the field proven technology and performance of Teledyne DALSA’s X64 frame grabbers the new Xcelera Series leverages the PCI Express (PCIe) platform to bring traditional image acquisition and processing technology to new levels of performance and flexibility. The PCIe host interface is a point to point host interface allowing simultaneous image acquisition and transfer without loading the system bus and involving little intervention from the host CPU. The X64 Xcelera-CL PX4 Dual is a highly versatile PCIe frame grabber capable of acquiring images from two independent Camera Link™ Base cameras and performing image transfers at rates up to 1024MB/s. Its low cost, combined with its ability to support multiple tap configurations from area and linescan monochrome/RGB cameras simultaneously; in addition to its onboard FPGA Bayer decoding and real-time shading correction makes the X64 Xcelera-CL PX4 Dual an ideal solution to a wide variety cost-sensitive applications.
-
product
Optic Node
OX 752
Converts even weak Optic Signals to a high quality RF Signal. LED BAR Optic Level Display has been provided for ease of system maintenance. They are best suitable for Analog as well as Digital transmission to maintain BER, MER Characteristics.- High Quality Nodes- Frequency 40 ~ 1000 MHz- Good Sensitivity of -11 dBm- RF O/P 110 dBµV at 0 dBm Optic I/P- High Voltage Surge Protection- LED Optic Level Display- Powder Coated Housing
-
product
120 A High Voltage 50 Ω Pulse Generator
TLP-12010C
High Power Pulse Instruments GmbH
- High pulse output current up to 120 A (short circuit)- Ultra-fast 50 Ω high voltage pulse output with typical rise time 100 ps (0 A to 40 A) and 300 ps in high-current mode (0 A to 120 A)- Wafer, package and system level TLP, VF-TLP and HMM testing- Up to 180 kW peak output power into 50 Ω load- Built-in HMM pulse up to ±32 kV in 50 Ω-configuration- High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)- 6 USB programmable pulse rise times: 100 ps to 50 ns (custom selectable)- 8 (optional 9) programmable pulse widths: 0.5 ns (optional), 1 ns to 100 ns (0 A to 40 A), 1 built-in pulse width: 100 ns (>40 A)- The optional pulse width extender TLP-3011C enables pulse width up to 1.6 µs in 68 GPIB programmable steps (0 A to 40 A)- Optional external pulse width extensions from 5 ns to 500 ns (>40 A to 120 A)using the external pulse width extender TLP-12012A6- Built-in pulse reflection suppression- Fast measurement time, typically less than 0.2 s per pulse including one-point DC measurement between pulses- Efficient sofware for system control and waveform data management- The sofware can control automatic probers for fast measurements of complete wafers- Combines TLP-12010A and TLP-4010C into one system- Can be operated together with TLP-12012A6 and TLP-3011C pulse width extenders- Integrated interlock safety shut-down- Industrial isolated and EMI/ESD protected USB control interface
-
product
PXI 4 Slot BRIC 368x4 1-Pole (4 sub-cards)
40-560A-021-368X4
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high-performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
Geiger Counter
USB-RAD121
The USB-RAD121 is a radiation detector that runs completely off your computer's USB port. The device features a classic geiger counter click and light pulse for every count registered, while radiation levels are displayed on the computer. The simple RadGraph software interface displays and graphs readings over time, and even allows the readings to be streamed to a personal webpage.
-
product
MPI Automated Probe Systems
MPI Advanced Semiconductor Test
MPI’s 200 mm and 300 mm automated probe systems are dedicated and designed to address current and future requirements for all facets of Device Characterization for Modeling and Technology/Process Development, Failure Analysis, Design Verification, IC engineering, Wafer Level Reliability as well as special requirements for MEMS, High Power, RF and mmW device testing.
-
product
Cryogenic Current Comparator (CCC)
6200A
Measurements International Ltd.
Introducing the Model 6200A Cryogenic Current Comparator Bridge (CCC) from Measurements International (MI) – the ultimate solution for achieving the highest level of resistance calibration accuracy. With an uncertainty of less than 3 parts in 10-9, our CCC surpasses all other technology on the market.
