Showing results: 2131 - 2145 of 6380 items found.
-
72-1015 CAL D -
Tenma
The 72-1015 CAL D from Tenma is a digital bench type true RMS multimeter. It has auto and manual range options with maximum reading of 5999 counts and 3-5/6 digits which has a unique outlook design. In addition to all the conventional features including DC/AC voltage, current, resistance, diode, continuity test, diode test capacitance, temperature, transistor, max/min, there is a data hold, low battery display, sleep mode, RS232C serial port for easy connection with computer to realize macro recording, monitoring and capture of transient dynamic data, displaying change of waveform during the measurement, providing data and evidence to engineering technicians for scientific research. This meter complies with the standards IEC61010, pollution degree 2, overvoltage category (CAT I 1000V, CAT II 600V) double insulation and CE marked.
-
783485-01 -
NI
Kintex 7 160T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module—The PXIe‑7821 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PXIe‑7821 supports peer‑to‑peer streaming for direct data transfer between PXI Express modules. The PXIe‑7821 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in-‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
TG2000 Series -
Aim-TTi
0.001Hz to 10MHz/20MHz frequency range6 digits or 1mHz resolution1ppm stability and 10ppm one year accuracyLow distortion, high spectral purity sine wavesInternal phase continuous sweep, lin or logAM, FSK, gated and tone switching modes5mV to 20V pk-pk from 50 or 600 OhmsStorage for multiple instrument set-upsUSB and RS232 Interfaces (TG2000 only)
-
Series MBT-G -
Kepco, Inc.
Kepco's MBT-G series (denoted by suffix "G") are bench-style instrumentation power supplies that offer a choice of control methods including direct entry keypad, slew up/down keys, rotary controls and three communications ports: IEEE 488.2, RS 232 and Kepco's single address, multiple instrument long range serial bus. These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
-
8012SH -
Sealevel Systems, Inc.
The 8012SH is Universal Bus (3.3V and 5V) compatible and ships with the standard size PCI bracket to allow installation in a full-size PCI slot. If you have a Low Profile PCI slot, order the 8012H. The inputs on the 8012SH are rated for 10-30V. For 3-13V inputs, order the 8012S.
-
Aplab Limited
- 2000W different combination- High current density.- 19″ rack adaptable -3U high- Front panel potentiometer to set V&I- Remote sensing- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation- Optional, at extra cost- Over voltage protection- 19″ rack mounting- Analogue programming and monitoring for V&I
-
Aplab Limited
- 3000W different combination- High current density.- 19″ rack adaptable -5U high- Remote sensing.- Front panel potentiometer to set V&I- 3Digit seven segment display for V&I- High stability and close regulation- Phase controlled preregulation plus linear post regulation Optional, at extra cost- Over voltage protection- 19″ rack mounting
-
-
12-1015 -
Associated Equipment Corp.
• Tests 12V Flooded, AGM, Gel Cell, Enhanced Flooded (Start/Stop Batteries)• 10 Line LCD display• Performs ground test• Checks diode ripple• Stores last 250 test series with or without power• Carrying case, printing software and USB cables included• Built-in thermal printer with thermal paper (611305)
-
APCI-2200-16-8 -
TEAM SOLUTIONS, INC.
16 electromechanical relays with change-over contacts ? Max. switching voltage for the relays: 60 V/DC, 48 V/AC ? Max. switching current: 1 A ? Short response time ? Option: 8 input channels for AC voltage, optically isolated, input voltage range: 12 - 24 V DC ? Watchdog: software-programmable release, stop and time selection.
-
72-9275 -
Tenma
Full featured multimeter with additional functions for automotive diagnosis. Measures AC/DC voltage, DC current, resistance, frequency, dwell, tach, duty cycle and temperature.
-
72-9165 -
Tenma
Feature loaded DMM includes multiple environmental testing functions replacing 6 testers: light meter, sound level meter, hygrometer, thermometer, non-contact voltage detector, and multi-function multimeter.
-
-
GP-X -
Panasonic Industrial Devices Sales Company of America
The inductive displacement transducers of the GP-X Series use eddy current techniques and are particularly noted for their highly accurate measurement at a resolution of 0.02% F.S. with minimal linearity error, a high sampling frequency of 40kHz and low temperature dependence. GP-X Series Sensors are ideally suitable for the highly accurate motion and distance control of metal objects in harsh industrial environments.
-