Continuity
Test devices which measure shorts over a large amount of test points.
-
product
HALT/HASS Testing
HALT HASS Chamber
AST applies stresses (such as temperature and vibration) to products well beyond its normal use environment. This type of testing is done to determine product operating and destruct limits. These stresses are applied as the product is functionally tested and continuously monitored for failures.Highly Accelerated Stress Testing (HALT) and Highly Accelerated Stress Screening (HASS) are two types of accelerated stress testing. These types of tests are commonly used to eliminate design problems, helping to develop a robust, mature product prior to market introduction. It can also be used to screen out infant mortality issues prior to shipment.
-
product
Analogue (1kV below) Insulation Tester
1180 IN
Standard Electric Works Co., Ltd
High quality Taut Band movement. Battery operated. Solid state circuitry. Battery check feature. Automatic circuit discharge. Three insulation test voltages(DC) : 250V, 500V, 1000V. Continuity test : 50 Ω. AC voltage measurement : 500V. Color-coded scale. Fuse protected.
-
product
Rebar
Continuously monitors the coating line process as reinforcing bar runs through the RBRS dual-roller wet sponge electrodes unit. When a holiday is discovered, a red light flashes at the appropriate station on the detector unit for a visual indication, and the unit sends an eletrical output to a plug on the back of the unit. The MSRB signal output plugs drive any 120 Volt AC customer furnished horn, bell, recorder or computer.
-
product
LAN Tester / Wiremap Tester & Cable Fault Locator
RapidTrace 700
Compact, Powerful and Easy to use. This high performance low cost LAN Tester / Wiremap Tester and Cable Fault Locator is the perfect tool to enable you to test and certify structured cabling continuity to TIA568A/B, USOC and ISDN standards.
-
product
MAX31855 K-Type Thermocouple Arduino Shield
SEN-30004-K03
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855K supports a measured temperature range of -270C-1372C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
product
LCR Component Meter with Component Impedance Measurement
LCR45
The new LCR45 does everything that the popular LCR40 does, but we've added some significant enhancements. The LCR45 features a new high capacity micro and high resolution ADCs.*Fluid measurements of L, C and R (continuous readings with selectable hold function).*Fine resolution for improved performance at low inductance/capacitance/resistance.*Auto and Manual component type.*Auto and Manual test frequency.*Frequencies: DC, 1kHz, 15kHz and 200kHz.*Display of component values, complex impedance, complex admittance and magnitude/phase.
-
product
Widely Tunable Ultrafast Laser System For Multiphoton Imaging
InSight X3
Spectra-Physics’ new InSight® X3™ is the third generation of Spectra-Physics’ industry leading InSight platform, specifically designed for advanced multiphoton microscopy applications. Based on patented technology1, InSight X3 features a broad 680 nm to 1300 nm continuous, gap free tuning from a single source, nearly double the tuning range of legacy Ti:Sapphire ultrafast lasers. InSight X3 delivers high average and peak power levels across the tuning range, including critical near infrared wavelengths above 900 nm for deepest penetration in-vivo. With Spectra-Physics’ integrated patented DeepSee™, the industry standard dispersion pre-compensator, the short pulses are optimally delivered through a microscope to the sample for maximum fluorescence and penetration depth. InSight X3 also has exceptional beam pointing stability, beam quality and output power stability, as well as fast wavelength tuning, making it ideal for microscopy.
-
product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781340-04
6.6 GHz PXI Vector Signal Generator—The PXIe‑5673E is a wide-bandwidth module that, when combined with the appropriate software, can generate a variety of signals. With the Modulation Toolkit for LabVIEW, it can generate different waveforms including AM, FM, CPM, ASK, FSK, MSK, PSK, QAM (4‑, 16‑, 64‑, and 256‑QAM), multitone signals, arbitrary waveforms, and many others. In addition, you can combine these vector signal generators with standard-specific software to generate signals for GPS, GSM/ EDGE/WCDMA, WLAN, WiMAX, DVB‑C/H/C, ISDB‑T, ZigBee, and others. With PXIe‑5673E stream‑from‑disk capabilities, you can generate continuous waveforms that are up to several terabytes in length.
-
product
Insulation Resistance Meter
AMIC-10k1
Insulation resistance measurement - 40TΩ: * 50 - 1000 V, in 25 V steps, * 1000 - 10000 V, in 50 V steps ; Memory, bluetooth keyboard option, heating location ; Measurement of AC and DC voltage and capacity ; Measurement of leakage current and function with digital filter ; Measurement of continuity of protection and equipotential connections ; Adjustable alarm limits.
-
product
3 3/4 Digit Autoranging Digital Multimeter w/Bargraph
HH2204
High Accuracy (Basic Accuracy 0.5%). Jumbo LCD display 3260 count, 27mm figure height. Auto Ranging or Manual Ranging at your choice. Higher Voltage test up to AC 750V and DC 1000V. Higher Current test up to 20A. Resistance test up to 30MΩ. Frequency test range up to 3000Hz. Diode test, audible continuity check and Transistor test
-
product
LAN Cable Tester
PA-01D
The LAN cable tester is a versatile, full-featured tool for testing many kinds of network cable. Loopback and remote tests may be performed automatically or manually, and will test cable continuity as well as identifying opens, shorts, reversed wiring, and miswiring in cables up to 2,000 ft. long. Shielded connectors allow the tester to test shielded twisted pair (STP) cables. The built-in tone generator generates a low emission frequency tone which can be detected by any market tone probe, making it easier to trace and locate cables. Uses 1 9V alkaline battery. CE Approved.
-
product
Active Network Assessment and Monitoring Platform
Hawkeye
Keysight Network Applications and Security
Network performance and user experience are critical aspects of your business. It is vital to understand customers’ perception of your website, application, and network services. NOT knowing impacts your revenue stream. Ixia’s Hawkeye continually measures network performance and service status. If there is an issue, Hawkeye helps you identify it, quantify it, and ultimately resolve it – before your customers experience it.
-
product
XCITE 1100-5 Inertial Mass Excitation System
The 1100-5 Inertial Mass Modal Excitation system allows the testing of structures where backup fixturing is not available or possible. Accelerating an internal mass with the closed loop hydraulic excitation system generates the inertial forces. The compression control of the Xcite Master Controller maintains a constant force over a frequency sweep by continuously altering the drive signal to maintain the required dynamic force level.
-
product
Corrosive Series Valved Cracker
With the superior flux control of the Corrosive Series Valved Cracker, complex structures not possible with conventional thermally controlled sources can be achieved. Mixed Group V layers of varying compositions can be grown without the frequent recalibration procedures necessary when using standard sources. SIMS analysis of a continuously graded GaAs1-xSbx layer demonstrates the excellent flux control available when using two Group V valved crackers, with identical results achieved at two different growth rates.
-
product
Cyber Security Training
Elbit Systems of America's comprehensive attack scenario library reflects the most recent threat landscape. Our cyber security experts continuously update training scenarios with newly discovered attacks and tactics. Versatile network settings and attack scenarios equip cyber security teams with customized training specific to each team's organization.
-
product
Open Path Infrared Gas Detector
IR5500
The IR5500 is an open path infrared (IR) gas detector that continuously monitors for flammable gas leaks over large open areas. It monitors in both the LEL-m and ppm-m ranges to detect both small and large leaks. The IR5500 offers the benefits of early detection with its high sensitivity to gas concentrations at the ppm levels.
-
product
Solar Analyzers
Max. solar system power (Pmax) search by Auto-scan: 1000V, 12A (12000W capability)The analyzer and the Remote Solar Detector is connected by Bluetooth wireless communication (Bluetooth 2.1 + EDR Class 1)The Remote Solar Detector is moisture-proofIntelligent test logic with no personnel attendance required in the field Solar system analyzer waits and tests the system until appropriate sunlight irradiance is detectedMax. voltage (Vpm) at Pmax, Max. current (Ipm) at Pmax Voltage at open circuit (Voc), Current at short circuit (Isc)Efficiency (%) calculation of solar systemTemperature measurement of solar panelsIrradiance measurement of sun lightSeries resistance (Rs) calculation of solar panelsWith data logging/open function, the I-V curves of solar system can be analysed / recorded for a period of time (e.g. 60 min.)Conversion of I-V curve under OPC to data under standard test condition (STC) based upon IEC standardProvide Operating Condition (OPC) and Standard Test Condition (STC) test reports for verification of solar panel performance (OK or NO OK)Users can set up the parameters of solar panelsUsers can set up the series number of solar panels. Parameters of many solar panels can be measured in one measurementThe Irradiances and Temperatures of solar panels can be continuously measured, monitored and recordedContinuously measure/monitor/record the DC power output of solar system and the AC power output of inverter (1 phase or balanced 3 phases)Calculate the efficiency of DC to AC power conversion and the efficiency of the max.output power
-
product
FTIR Gas Analysers
Protea’s range of Fourier Transform Infrared (FTIR) Gas Analysers allows for the measurement of nearly any gas with one instrument. A FTIR gas analyser collects a full infrared spectrum continuously, allowing for hundreds of gases to be detected and measured at once. Changes are only needed to software calibration files to measure new gases.
-
product
The Integrator
L.Net converter
Electronic Solutions ULM GmbH & Co. KG
The great variety of the ESU ECoS command station is so convincing to many model railroaders that they would like to replace their present digital station with an ECoS. This also has been inspiring the desire to continue to use the existing handheld throttles and feedback modules. The ECoSniffer input offered at least a solution for handheld throttles (in combination with „older"digital command stations), whereas the feedback modules couldn’t be integrated into the system.
-
product
Cable Integrated Detector
DTR-500
This machine is a multi-frequency with high-power transmitter, with constant power output and automatic matching of external load, which could ensure the machine to work in the best status. With ohmmeter, it could detect the external voltage and test the continuous circuit resistance to help judging the fault properties.
-
product
Automatic Component Analyzer
TH2829A
Changzhou Tonghui Electronic Co., Ltd.
By dint of leading impedance measurement technology and rich R&D experience, Tonghui continuously introduces representative impedance measurement product --- TH2829 series automatic component analyzer is another excellent product we have produced. TH2829A automatic component analyzer possesses a higher test speed, a more comprehensive analysis function and friendly human-computer interactive experience by adopting the latest high-speed processor and a new software system. Well-designed measuring circuit and optimized algorithms further enhance the test stability of low-D capacitance and high-Q inductors. The instrument is provided with 10V AC test level, 10V/100mA bias current and standalone 10V/50mA DC current, making it convenient for applying in the test of all kinds of active/ passive devices. Main/ sub parameters display, enhanced display system design, 150-points list sweep and graphical analysis capabilities of multiple parameters meet the most application requirements of customers.
-
product
Mobile Test Lane
Maschinenbau Haldenwang GmbH & Co. KG.
Self-supporting steel container 20 ft. To DIN ISO 668Electro-hydraulic-place incl. Wired remote controlOffice with computer station for inspection personnelHydraulically actuated, sanded entry and exit rampsPC control of test equipment over EUROSYSTEMElectromechanical liftable roof with weather protectionAir conditioning for office (optional)Integrated continuous current unit to supply the complete test as well as the Aufstellmechanik / hydraulics (option)Turning device 360 ° for container (option)Upgradable to a complete test with:
-
product
SCSI CABLE TESTER
ST123
Continuity tests alone are not sufficient to qualify SCSI cable assemblies. Proper testing of SCSI cables must include a test for correct connection of twisted pairs and shielding. Continuity tests check only that wires are making connections on both ends of a cable.Twisted pairs in the cable must be matched with the correct SCSI signal pairs - otherwise, it is possible to have a SCSI signal (signal and ground pair) placed on wires that are not in the same physical twisted pair (see diagram at right). This will cause crosstalk with resultant SCSI errors.
-
product
Broadband Power Amplifiers
Our range of broadband power amplifiers are designed using the most suitable devices and techniques. We don’t believe in following fashion in our choice of parts, but will continue to use older technology where it is still the best, and incorporate the new where improvements can be made.
-
product
In-Process / In-Line Spectrophotometers
Hunter Associates Laboratory, Inc.
Installed within a process stream, in-process (in-line) spectrophotometers provide continuous color measurement data throughout a production run, enabling quick responses to color variations.
-
product
Hand-held pressure gauges
HPM110
The HPM110 digital pressure gauge is designed for continuous monitoring of oil, water, hydraulic and other pressure media in mobile equipment, industrial hydraulics, and process control equipment.
-
product
PXI Solid State Multiplexer, 30 Amp, Dual 3-Channel
40-667A-011
The 40-667A-011 is a dual 3-channel 30A MUX and is part of our range of high current multiplexers occupying two slots of PXI chassis. Each multiplexer switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each multiplexer channel can support 10A of continuous current and switch up to 200V signals. The switches can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
Pen-type Visual Fault Locator (VFL)
JW3105P
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
The JW3105 Pen type VFL is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in optical network. It includes:
-
product
Handheld Wiring Analyzer
HT-128+
Reduce your wire harness assembly and installation difficulties now. The NEXU HT-128+ test platform provides a valuable tool for multi-point wiring continuity analysis. Our versatile, lightweight, handheld unit can serve your wiring test and maintenance needs from harness layout to product field support. The HT-128+ performs testing and troubleshooting, automated ring-out, directed assembly plus other features to resolve wiring issues quickly to achieve increased product availability!
-
product
HF/HNO3 Monitor
CS-153N
The CS-153N is a high-precision chemical solution concentration monitor designed to meet the strict demands of semiconductor wet-etching processes. Etching processes use HF/HNO3 solution to etch silicon oxide and remove particles from the wafer surface. The CS-153N continually monitors each component of the HF/HNO3 solution (HF/HNO3/H2O), alerting the user each time the solution is replaced or replenished. This allows you to maintain the concentration of the HF/HNO3 solution within the tolerance range, while eliminating unnecessary solution replacement.
