Continuity
Test devices which measure shorts over a large amount of test points.
-
Product
Power System Recorder with CDR , PMU and IEC 61850 station bus protocol
TESLA 4000
-
ERLPhase Power Technologies Ltd
The new TESLA 4000 is an intelligent, state of the art, user-friendly multi-timeframe dynamic power system recorder with advanced Phasor Measurement Unit (PMU) and Continuous Disturbance Recording (CDR) capabilities. Wide area swing recording accomodates system performance analysis in minutes Meets NERC continuous disturbance recording standards with non-volatile on board flash memory No mechanical moving parts – flash drive eliminates most common mode of failure in recorders. Each flash drive holds 1000 records. IEEE C37.118-2005 SynchroPhasor Standard
-
Product
Phase Squence Tester
-
Measurement Range3 phase check for AC 90V ~ AC 600V (Sine Wave) Operation Frequency45Hz ~ 70Hz Test Time LimitationAC 110V(continuous)AC 220V(3 hours)AC 480V(12 minutes)AC 600V(3 minutes) Power Supplyno battery required Color change LED phase direction indication
-
Product
Spectrum Analyzer Plug-in
FreqAnalyst
-
This plug-in has been designed to provide extreme smoothness and high resolution for both time and frequency: unlike most spectrum analyzers, Blue Cat's FreqAnalyst is able to display continuous variations even with a very high frequency resolution, thanks to its unique smooth interpolation algorithms.
-
Product
Differential Scanning Calorimetry
Nano DSC
-
The Nano DSC differential scanning calorimeter is designed to characterize the molecular stability of dilute in-solution biomolecules. The Nano DSC obtains data using less sample than competitive designs. Solid-state thermoelectric elements are used to precisely control temperature and a built-in precision linear actuator maintains constant or controlled variable pressure in the cell. Automated, unattended continuous operation with increased sample throughput is achieved with the optional Nano DSC Autosampler.
-
Product
PFC Controllers
-
Renesas' power factor correction (PFC) controller family uses boost topology and are suitable for AC/DC power systems, up to 2kW and over the universal line input. These PFC controller IC's operate in continuous conduction mode (CCM), and the small external components result in a low cost design without sacrificing performance.
-
Product
Semiconductor
-
With ultra-multi pin count and fine pitch, our general-purpose IC socket lineup corresponds to every need. For semiconductor burn-in sockets for thermal acceleration tests, and test sockets for semiconductor electrical testing, we continue to hold a high market share all over the world.
-
Product
PC Controlled High Voltage Tester
Cablescan H23
-
The Cablescan H23 combines low-voltage solid-state technology with high-voltage relay technology ¾ solid-state devices for testing continuities and components at low voltage; relays for testing high-resistance isolation and high-current continuity.
-
Product
1000A AC Clamp Meter
CM55
-
The CM55 is a pocket sized high performance AC Clamp meter measuring AC current, AC/DC voltage and resistance with continuity test. The compact rugged design enables accurate and reliable current measurement down to 10mA resolution without the need to break into the circuit.The CM55 has a CATIII 600V safety rating and is the ideal tool for residential and commercial electricians.
-
Product
Handyscope TP450-250XM-W5
TP450-250XM-W5
-
The Handyscope TP450 is a power quality analyzer, connected via USB to the computer. The advanced measurement software delivered by default contains Quick Setups that allow to start mains power logging measurements without specialized instrument knowledge. With the 450 V input range, the Handyscope TP450 can be plugged directly in a (110 - 230 V) wall socket to measure the mains voltage. No additional attenuator is required. Logging mains voltage can be done at a high rate of 250 thousand measurements per second, with a resolution of 16 bit, which is equal to a 5½ digit voltmeter. The Handyscope TP450 is an accurate voltmeter, but one that performs 5000 measurements on each cycle of the mains voltage, while a standard voltmeter performs 3 measurements per second. Even with the very high measurement rate of the Handyscope TP450, the mains voltage can be measured continuously for weeks, and afterwards each period of the mains voltage can be analyzed thoroughly. Using this fast continuous measuring method, no voltage peak or dip is missed, even if it lasts just a msec. The maximum measuring duration of the mains voltage is only limited by the available hard disk space. Measuring one week takes approximately 0.69 GB disk space. During a measurement, also RMS value and frequency are logged. It is possible to measure various properties, like e.g. Minimum, Maximum, Peak to peak, Mean, Variance, Standard deviation.
-
Product
Mechanical Creep and Rupture Testing Machine
MRC Series
-
Jinan Testing Equipment IE Corporation
MRC series mechanical creep and rupture testing machine with single-lever structure is designed for long-term creep and stress rupture test applications. The series mechanical creep and rupture testing system is mainly for the metallic materials under room or elevated temperature according to GB/T2039, GB/T 20120, EN ISO 204-2009 and ASTM E139. The creep and rupture testing machine can also maintain constant loads for extended periods of time. Through the mechanical advantage of the lever arm loading system, constant loads can be maintained with a high degree of accuracy for long duration. This creep and rupture tester uses dead weights without continuous operation and the dependency of a mechanically powered drive. The creep and rupture testing system is an ideal equipment for metallurgy manufacturer, research institute, colleges and other relevant factories and mines.
-
Product
Fanless Ultra Compact Embedded System With Intel® Core™ I5-7300U &Intel® Celeron® 3965U Processor, DisplayPort++, 2 COM, 4 USB And 2 GbE LAN
eBOX100-51R-FL
-
The eBOX100-51R-FL is a fanless ultra-compact embedded system with weight 600 grams only. As the smallest embedded system with Intel® Core™ ULT processor onboard, the eBOX100-51R-FL continues the design elements of eBOX100 series – ultra-slim form factor, rugged design, and rich I/O connectivity, allowing greater flexibility and a wider range of application in edge computing, IIoT gateway and extended fields. The eBOX100-51R-FL is powered by the high-performance Intel® Core™ i5-7300U or Intel® Celeron® 3965U processor. The front-facing I/O connectivity design provides convenient access for easy installation and maintenance. It comes with one DDR4-2133 SO-DIMM slot with system memory up to 16 GB. The eBOX100-51R-FL offers two RS-232/422/485, two USB 3.0 ports, two USB 2.0 ports, two Gigabit Ethernet ports, one DisplayPort++, one AT/ATX quick switch, and two SMA type antenna openings; moreover, the embedded system is equipped with one M.2 Key E 2230 slot for Wi-Fi, one M.2 Key B 2242 for SATA storage, and one screw-type 12VDC power input connector.
-
Product
Hygrometer
308
-
The Elcometer 308 Hygrometer has been specifically designed for use in very hot climates where the surface temperature of the substrate can exceed the paint manufacturer’s recommended limits for successful painting.Painting outside recommended limits can have a detrimental affect on the performance and lifetime of the coating.Key features of the Elcometer 308 Hygrometer include:Rugged design: Suitable for use in extreme environments the Elcometer 308 Hygrometer is dustproof and waterproof with fully sealed sensors.Measurement Hold / Release function: With a single button press readings are ‘held’ on the screen. These can then be recorded before simply pressing the button again to ‘release’ the screen and continue to take further readings as necessary.Backlight: Bright screen making information easy to read – ideal in dark or confined spaces.
-
Product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781340-03
Vector Signal Generator
6.6 GHz PXI Vector Signal Generator—The PXIe‑5673E is a wide-bandwidth module that, when combined with the appropriate software, can generate a variety of signals. With the Modulation Toolkit for LabVIEW, it can generate different waveforms including AM, FM, CPM, ASK, FSK, MSK, PSK, QAM (4‑, 16‑, 64‑, and 256‑QAM), multitone signals, arbitrary waveforms, and many others. In addition, you can combine these vector signal generators with standard-specific software to generate signals for GPS, GSM/ EDGE/WCDMA, WLAN, WiMAX, DVB‑C/H/C, ISDB‑T, ZigBee, and others. With PXIe‑5673E stream‑from‑disk capabilities, you can generate continuous waveforms that are up to several terabytes in length.
-
Product
Traveling Wave Fault Locator
XC-2100E
-
XC 2100E, a Fault Location System based on principle of travelling wave detection is the solution to above problem. It can detect not only permanent fault, but also transient fault within one tower span accuracy (with best accuracy of ±50 meters). It is a kind of Line Monitor for continuous monitoring of transmission lines and gets triggered whenever travelling waves are generated on line due to switching, lightening or fault.
-
Product
PCI Relay Driver Card, 64-Channel
50-411A-001
Relay Driver
The card provides 64 channels of low side switching for external relays. Users need to simply connect a positive voltage source to one terminal of a relay coil and the other terminal to an output of the 50-411A. Each output is capable of sinking up to 1A of continuous current.
-
Product
Process Analyzers
MARGA
-
MARGA is a fully autonomous sampling and measurement system that continuously measures the water-soluble gas and aerosol components that have a direct effect on air quality. These results can then be used to study the formation of aerosols from their precursor gases and how their concentration and composition vary with diurnal and seasonal cycles.
-
Product
CrashSim
-
The application software CrashSim is used for the preparation, execution, monitoring, analysis and documentation of crash tests carried out on the Instron sled system. The user application focused software has been continuously improved in cooperation with our worldwide user groups.
-
Product
Level Switches
-
In point level detection, a point level switch detects when a certain predefined level is reached. Such a device is employed when it is not necessary to measure every possible intermediate level, as is the case with continuous level measurement. A switching command starts or stops filling equipment such as conveyors or pumps. Point level switches outputting a binary signal can be integrated into a process control system.
-
Product
Power Monitoring Software
-
A digital tool that continuously tracks, analyzes, and manages a facility's electrical system in real-time.
-
Product
FIAT Oxygen Sensor
KS60113 - FIAT
-
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
Product
MODEM SHARING DEVICES
-
The Modem Sharing Devices are designed to allow RS-232 DTE (terminal) devices to share Leased Line and Dial line Modems or DSU's. Data arriving at the Master Port is continually broadcast to all Subchannels. The attached terminal device that raises the RTS control signal is automatically given control of the MSD. Data rates of up to 128 Kbps are supported.
-
Product
Continuity Tester
1670
-
Peaceful Thriving Enterprise Co Ltd
1. For automotive, marine, aircraft and home appliances. 2. Detect open circuit in fuses, diodes, switches, sockets and wires.
-
Product
Milliohm Meters
-
PeakTech Prüf- und Messtechnik GmbH
Measuring device in a splash-proof hard case for professional field service use, e.g. for resistance measurement on motor coils, generators and transformers or for continuity testing on ring bus systems in industrial plants.
-
Product
Airborne Network Flight Recorder
TTC nREC-4000S
-
Curtiss-Wright Defense Solutions
The TTC nREC-4000S-2 is an intelligent IP flight recorder. The unit records data from network-based data acquisition and multiplexing devices and, with built-in intelligence, supports extensive recorder statistics and provides continuous health monitoring.
-
Product
14 Bit 4-Kanal Arbitrary Waveform Generator Mit 4 X 600MS/s Od. 2 X 1,2GS/s
PXDAC4800
-
The PXDAC4800 is an exceptionally high-speed four channel Digital to Analog Conversion (DAC) board which may be used as an Arbitrary Waveform Generator, a waveform playback device, or for generating multiple communication frequency bands. Each DAC can output data at a maximum real rate of 1.2 GSPS at 14-bit for two channels or at 8-bit for four channels, or 600 MSPS at 14-bit for four channels. Each output signal has a bandwidth of up to 400 MHz for AC-Coupled configuration or up to 590 MHz for DC-Coupled configuration. Output waveforms may be “per-trigger” or “continuously looped” from the on-board 1 Gigabyte memory.
-
Product
Audio Frequency Transmitter
TG 20/50
-
Cable fault location with the BAUR TG 20/50. The TG 20/50 is a portable, battery-operated audio generator with a built-in charging unit. Together with the UL audio frequency receiver and the SP detecting rod, the TG 20/50 is used for cable tracing, twist method and for determining the depth of cables and metal pipes.* Automatic or manual impedance adjustment* Charging unit and rechargeable battery integrated; battery or mains operation* Continuous or cyclical output* Two output frequencies selectable
-
Product
Power Quality Analysers
EPPE
-
Power quality measuring systems with integrated fault recorder functionality for continuously and automatically monitoring electrical installations at all voltage levels. The measuring systems of the EPPE series continuously and precisely record all the electrical parameters of the power supply. They deliver detailed quality evaluations which reveal even the smallest of deviations and contribute to identifying the cause of disturbances.
-
Product
PXIe-5764, 16-Bit, 1 GS/s, 4-Channel PXI FlexRIO Digitizer
785171-01
FlexRio Digitizer
The PXIe-5764 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PXIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
SM & MM Quad Optical Loss Test Set
KI2724-INGAAS-APC
-
A SM & MM Quad Optical Loss Test Set used to test power, insertion loss, continuity and faults on multimode and single mode fiber with an APC connector at 850 / 1300 nm & 1310 / 1550 nm. In a small package, it provides a powerful solution to improve test flexibility and productivity.
-
Product
Digital to Synchro Converters
DSP
Digital / Synchro Converter
Computer Conversions Corporation
The DSP Series are high efficiency, AC Reference powered, Transformer Isolated, continuously updating “whole” Digital to Synchro Converters, designed for high performance Military and Industrial applications.
