Battery Capacity Testers
determine the condition of batteries to provide power.
See Also: Battery Testers, Battery Checkers, Lead Acid Battery Testers, Battery Conductance Testers, Battery Load Testers
-
-
Product
Automated Leakage Current Tester
LINECHEK® II Series
-
Our LINECHEK II Leakage Current Tester is designed for medical device manufacturers. With a feature set built around maximizing the efficiency of the Leakage Current test, LINECHEK II satisfies medical application requirements demanding up to 40 Amps of continuous line current. Use it on the bench or in a rack, from the front panel or via a PC interface to ensure your medical device is ready for global deployment.
-
Product
Battery Impedance Tester
-
TES Electrical Electronic Corp.
Test conditions without shutting down battery.Simultaneously measures battery resistance, Voltage, current, and temperature.Auto-hold and auto-data storage. Comparator Function.Rates conditions as pass, warning, or fail.
-
Product
Electrical Testers & Voltage Continuity Testers
-
Fluke’s line of electrical testers and voltage detectors are designed for use in every application and in nearly any environment. From non-contact voltage detectors and voltage testers with continuity detectors, to open-jaw current testers and open fork testers with FieldSense® technology (for voltage and current measurements without test leads), these testers are accurate, safe and easy to use.
-
Product
AC/DC Leakage Current Tester
228
-
Test for dangerous leakage current with the Simpson Model 228, designed to meet the latest UL, IEC, and ANSI specifications. The 228 detects both AC and DC leakage current and simulates human response at three different levels -- reaction, let-go, and burn hazard. Each Model 228 comes with test leads with alligator clips, manual, and batteries.
-
Product
Power Module Tester
-
The Power Module Checkout ATE is developed for testing DC-DC Power modules typically utilized in India's space program. The DC-DC converters are exhaustively tested for all design parameters including supply voltage range, line and load regulation, efficiency, ripple, noise, transient response and so on. Special power sources and loading mechanisms are deployed to enable testing of various types of power modules.
-
Product
Air Conditioning Valve Tester
ACT-2
-
Today, almost every car is equipped with an air conditioning system. AC systems have become an active factor in driving safety, and can be considered as safety technology. Air conditioning system, like others, requires periodic maintenance and skillful diagnosis in case of malfunction. While design and operation of older systems is generally known, new solutions require more knowledge.
-
Product
Socket Testers
-
Socket Testers including 4 Pole RV Output Socket Tester, Blade Socket Tester, 7 Pole Plug Output Tester, 7 Pole Socket Output Tester.
-
Product
PXI Battery Simulator 2.8 Amps
41-753-001
-
The 41-753 is a battery simulator module that can be used to simulate the power supplies of cellular phones and other portable battery devices. It features fully floating output terminals that can deliver voltages up to 6 Volts. The fast responding remote sense connections allow the module to regulate the supply voltage at the device under test.
-
Product
100kV Withstanding Voltage Tester
-
AllWin Instrument Science and Technology Co., Ltd.
1. Leakage current at real-time detection2. Alarm value can be preset freely3. Audio alarm, High-voltage breakdown protection
-
Product
Shock/Bump Multifunctional Tester
DP-201
-
King Design Industrial Co., Ltd.
Shock or bump test mainly simulate the impact effects of product and its components encountered in usage and transit process. Through standard and high-reproducibility instant energy exchange, you can analyze the product ability to tolerate the strong external stress and the degradation of structural weaknesses to quickly obtain the data of structure strength, anti-shock appearance and anti-drop. Shock tester is one of destructive experiments, and do destructive test on the product to evaluate the product reliability and monitor the consistency of production line.
-
Product
Transient Immunity Tester
KES7700
-
Transient Immunity Tester KES7700 Series are transient surge tester that utilizes a compact unit system. A surge generator circuit is installed for each pulse unit as the tester meets the requirement of ISO7637-2, ISO7637-3, ISO16750-2, JASO D001, SAEJ1113, and other standards. The KES7700 Series meets a broad range of independent automobile manufacturer standards as well.
-
Product
Impulse Spark Tester
IT-25B
-
While most military standards now favor high frequency spark testing over impulse spark testing, the IT-25B Impulse Spark Tester is available for use in some aeronautic applications that still specify the impulse method. The IT-25B meets the test requirements of military specifications MIL-C-13777E, MIL-W-16878, and NEMA standards for hook-up wire used in high temperature wire applications. This method is favored as an alternate to a wet dielectric test.
-
Product
Automotive Battery Testers
-
ELAK Battery Testers are high-rate discharge testers. These testers impose a load on the battery, which is equivalent to that drawn by the starter motor from the battery, while cranking the engine. The tester studies the drop in battery voltage & indicates the condition of the battery if it is capable of starting the engine or not.
-
Product
Bit Error Rate Tester
100G NRZ BERT
-
The C-BERT 2810-4 is a complete bit error rate tester dedicated for 100G Ethernet applications. The four independent channels enable an actual operating environment with traffic on all lanes. The simultaneous testing of 4 channels is much faster than testing each channel individually saving time and money. The BERT eye scan reveals low-probability events and shows the true performance of the DUT to aid troubleshooting. The high RF port density eliminates long cable length which degrades the signal at 25 Gb/s. The OS independent GUI is easy to install and enable remote control from everywhere. The complete and compact C-BERT is a powerful and cost efficient test solution for 100G Ethernet.C-BERT MI-PE2810-4 Product sheet_rev05.
-
-
Product
Tachometer Indicator-Generator Testers
-
Hydraulic Technology Tachometer Indicator-Generator Testers
-
Product
Battery/Alternator Tester
BT55U
-
Schumacher Electric Corporation
BATTERY/ALTERNATOR TESTERFOR TESTING:• Battery state of charge• Charging system outputFEATURES:• Accurate, easy-to-read LCD screen.• Checks the battery, alternator systems• Two LED indicators• Overvoltage and Reverse Polarity Protection Contents: (1) Battery/Alternator Tester
-
Product
EOL Tester
-
A specialized automated system used in manufacturing to perform final functional and quality checks on products right before they leave the assembly line, ensuring each unit meets design specifications, works correctly, and complies with safety standards, covering everything from basic continuity and calibration to complex performance simulations.
-
Product
CDM testers
Scorpion
-
Scorpion opens a new generation of CDM testers. It is designed to meet the new JS-002 standard and features Contact First pulse delivery. This patent pending technique of Contact CDM (CCDM) meets the latest CDM standards with higher accuracy for device classification.
-
Product
NFPA 701-1 Flammability Tester
TF320
-
TESTEX Testing Equipment Systems Ltd.
NFPA 701-1 Flammability Tester, to determine the ignition resistance properties of draperies and other hanging fabrics according to test method NFPA 701#1, and it is suitable for single-layer or multi-layer fabrics, but not suitable for fabrics with density larger than 700g/m2 (21oz/yd2).
-
Product
PAT Testers
-
Complete with a comprehensive range of PAT labels, adaptors, software and our bespoke range of PAT testing kits we can cater for electrical safety testing in domestic, commercial and industrial environments.
-
Product
Multifunction Tester
M70
-
M70 is a mobile device dedicated to measuring Insulation resistance with test voltage up to 1000VDC and Continuity of protective and equipotential conductors with current of 200mA in private and industrial electric installations.
-
Product
Hydrostatic Head Pressure Tester
-
Sataton Instruments Technology CO., Ltd
Hydrostatic head pressure tester is designed to determine the resistance to water penetration of materials by hydrostatic pressure method. By measuring the opposition to the passage of water through the tested specimen, the tester is to provide standard testing conditions for operator to note the test terminal point. The tester is primarily intended for ducks, tarpaulins, tentings, waterproof materials and other materials which are used for impermeable application, such as chemical protective clothing or medical protective clothing.
-
Product
Transformer Oil Tester
GTD-61A
-
1. The GTD-61A Automatic Oil Tan Delta(OTD) & Oil dielectric loss tester is highly automated, allowing for the measurement of temperature rise, dielectric loss, and resistance in one go.
-
Product
Digital Hardness tester
THL270
-
Pen type Leeb hardness tester Converts to all common hardness scales (HL.HV,HB,HRC,HRB,HRA,HS). The machine also include interface to connect with impact device C, DC, G, D+15, DL
-
-
Product
In-Line Spark Tester
ST20610
-
Connect the tool between the spark plug and the plug wire to provide a quick visual check and diagnosis of the ignition system, including distributor-less ignitions. Plug wire is double-ended with a straight boot and a 90 boot for confined areas. With the engine running, the bulb mirrors the ignition spark.
-
Product
Vibration Testers
-
Lansmont’s Vibration Test Systems are simple to operate safely and can perform a wide range of vibration tests in accordance with government, industry and corporate specifications.
-
Product
Battery Acid Refractometer – Sulfuric Acid Specific Gravity
H2SO4
-
Measure battery acid safer and more precisely. The MISCO Palm Abbe digital refractometer eliminates bringing acid up to your eye – a risk associated with analog/shadow line models. This refractometer has a single scale for sulfuric acid specific gravity.
