Motion Controllers
Coordinate motion and timing.
-
Product
EtherCAT Master Multi-Axis Motion Controllers
DMC-52xx0
-
The DMC-52xx0 EtherCAT Master is Galil Motion Control's first 32 axis motion controller. It is a pure EtherCAT controller capable of controlling up to 32 drives and 2 IO modules on one EtherCAT Network in a small, space efficient package. The DMC-52xx0 makes configuration and programming easy with just a handful of EtherCAT configuration commands and Galil’s intuitive, two-letter programming language. The DMC-52xx0 is offered in 2, 4, 8, 16, and 32 axis formats. Coordinated moves can be done within banks of 8 allowing for minimal changes to Galil’s programming language. Galil supports a variety of EtherCAT drives to accommodate most applications. The DMC-52xx0 operates in Cyclic Synchronous Position mode (CSP). In this mode the servo control loop is closed on the EtherCAT drive while the Galil sends motion profile data at a 1 kHz rate. The DMC-52xx0 features 8 uncommitted opto-isolated inputs and 8 uncommitted opto-isolated high power outputs. It also includes 8 uncommitted analog inputs and 8 uncommitted analog outputs. One 100 Mbps Ethernet port and one USB (serial) port are provided for communication with a host PC or external devices.
-
Product
ISA Optima Motion Controllers, 1-8 axes
DMC-1700
-
The DMC-1700 for the ISA bus is a member of the Optima Series, Galil's full-featured multi-axis motion controllers. Designed to fit in a single ISA slot of a PC, the DMC-1700 controllers accommodate 1- through 8-axis formats and allow control of step or servo motors on any combination of axes. Any mode of motion can be programmed including linear and circular interpolation, contouring, electronic gearing and ecam.
-
Product
Ethernet-based 4-axis Motion Controllers
EMX-100
-
EMX-100 is a 4-axis Ethernet-based external motion control box with high scalability and minimal maintenance cost makes it the great choice for adding the motion function expansion ability within non-standard equipment, for all kind of general motion application.
-
Product
DSP-Based 4/8-Axis Advanced Pulse-Train Motion Controllers
AMP-204C/AMP-208C
-
ADLINK"s new AMP-204C/AMP-208C DSP-based 4/8-axis advanced pulse-train motion controllers incorporate up-to-date floating-point DSP and FPGA technology, enabling high pulse output and encoder input frequency up to 6.5 MHz and 20 MHz respectively. Leveraging ADLINK" s Softmotion technology, the AMP-204C/AMP-208C offer impressive comprehensive and application-oriented motion functionality to reduce development time while maintaining superior throughput and accuracy. Superior synchronous motion control performance combines with point-table function integrating multi-dimensional interpolation, such as 3D linear/circular/spiral interpolation with enhanced trajectory and velocity planning, for contouring applications in semiconductor, display and conventional manufacturing industries. The AMP-204C/AMP-208C also support PWM control with three different control modes for frequency or duty cycle, benefiting laser engraving/marking/cutting applications. Moreover, hardware-based position comparison and trigger output are applicable in AOI applications.
-
Product
EtherCAT Master Multi-Axis Motion Controllers
DMC-500x0
-
The DMC-500x0 EtherCAT Controller is Galil Motion Control's newest entry in its latest generation of digital motion controllers. Incorporating all of the features of our flagship Accelera series controller and designed with compatibility and flexibility in mind, the DMC-500x0 allows integration of remote EtherCAT drives into new and existing applications with just a handful of configuration commands. The DMC-500x0 is offered in 1 through 8 axis formats. Axes 1 - 4 can be configured as either local or EtherCAT drives while axes 5 – 8 can be configured for additional EtherCAT drives. Unique to the motion control industry, this ability to mix and match local and EtherCAT drives on the same controller provides increased flexibility for any application. In addition, the DMC-500x0 is fully compatible with Galil’s internal servo and stepper motor amplifiers as well as third party external drives.
-
Product
Multi-Axis Motion Controllers
DMC-40x0
-
The DMC-40x0 motion controller is Galil's highest performance, stand-alone motion controller. It belongs to Galil's latest generation motion controller family, which accepts encoder inputs up to 22 MHz, provides servo update rates as high as 32 kHz, and processes commands as fast as 40 microseconds-10 times the speed of prior generation controllers. The DMC-40x0 is a full-featured motion controller packaged with optional multi-axis drives in a compact, metal enclosure. The unit operates stand-alone or interfaces to a PC with Ethernet 10/100Base-T or RS232. The controller includes optically isolated I/O, high-power outputs capable of driving brakes or relays, and analog inputs for interfacing to analog sensors. The DMC-40x0 controller and drive unit accepts power from a single 20-80 VDC source.
-
Product
PC-Based Motion Controllers
-
All-in-one controller is a programmable PC-based controller based on MotionNavi API library
-
Product
Advanced 8/4-axis Servo & Stepper Motion Controllers with Modular Design
PCIe-8158
-
The PCIe-8158 delivers high-frequency pulse rates up to 6.55 MHz and hardware-controlled emergency stop, software security protection, card index switching, and simultaneous linear/ circular run, exceeding industrial cost/performance requirements. Compatible with Mitsubishi, Panasonic and Yaskawa servos and any pulse-train controlled servo and stepper drives, the PCIe-8158 allows complex moving patterns through multiple axes that move with linear and circular interpolations using continuous contouring. Applicable for a variety of linear and circular trajectories, the PCIe-8158 delivers the smoothest motion control for a wide range of manufacturing applications. Modularized configuration accommodates ADLINK extension boards for distributed I/O control and high-speed triggering functions.
-
Product
Zero Speed Sensors
-
SPECTEC Innovative Sensor Solutions
The Hall effect technology fulfills a wide array of applications due to the Hall effect sensor's ability to detect zero speed and direction change and produce a digital output that is read by computers, motion control devices, position monitors and digital to analog converters.
-
Product
Intel® Atom™ Processor E3845 1.9 GHz-based EtherCAT Master Controller
Talos-3012
-
The ADLINK Talos-3012 EtherCAT master controller, based on the Intel Atom quad-core processor E3845 1.9 GHz, with IEC-61131-3 compliant syntaxes, delivers reliable control for multiple axes and versatile I/O control supporting specialized real-time applications. The Talos-3012 supports up to 64-axis motion control and 30K points within determined cycle times, and is verified for interoperability with various EtherCAT servo drives and 3rd party EtherCAT products.
-
Product
Machine Controllers
-
The flexible design of Yaskawa machine controllers allows cost-effective configuration of motion control for any sized automation system. Controllers can be easily adapted for stand-alone use on a single axis, for networking with other control devices or for complete control of a multi-axis machine.
-
Product
Real-Time Motion Controller
-
Advantech provides two types of motion controller: PC-Based Programmable Motion Controller and Standalone ARM-based Motion Controller.
-
Product
EtherCAT Server Modules
-
Advantech offers a variety of distributed I/O and motion control EtherCAT modules, such as isolated digital input, isolated digital output, photoMOS relay output, relay contact, analog input/output, pulse output, and junction modules to satisfy diverse control application needs.
-
Product
Sun Trackers
STR-series
-
EKO Sun Trackers are very compact, robust, relatively light weight and very power efficient. Inside the Sun Tracker a Harmonic Drive with advanced motion control unit is used on each output shaft. Harmonic drive is a leading drive technology for those application where high precision, durability, low backlash, high transmission ratios and torque is required. Due to its compact design and high transmission ratio small motors could be used to keep the power consumption low.
-
Product
32-CH Sinking Type Digital Ouput EtherCAT Module
EPS-2132
-
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
Motion Control Terminal Board For Mitsubishi J2S-A Servo Amplifiers
DIN-812M0
-
- On-board connector type: 100-pin SCSI-II female- Suitable for Mitsubishi J2 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8132
-
Product
Motion ASIC
-
Designed by Motion ASIC and offers high-performance and fast control response to meet a wide range of advanced motion control features
-
Product
REM-11152, 16-Channel (Input), 24 V, 2-, 3-, 4-Wire Digital Module for Remote I/O
784743-01
-
The REM‑11152 is a digital input module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11152 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. The REM‑11152 features 2‑, 3‑, and 4‑wire spring terminal connection methods, a built-in power supply for sensors, and an adjustable filter time to improve measurement quality. You can use inputs as counters or standard digital inputs.
-
Product
Intel Atom® Panel Controller
AMAX-PT700 V2
-
Optimized BIOS & Embedded OS for 1ms real-time control (Windows and Linux)Achieve 32-axis motion control with 1ms EtherCAT cycle time under LinuxOPC UA and Modbus TCP/RTU as IT connectivity enabled by CODESYSEtherCAT, PROFIT, Ethernet I/P, CANopen as OT connectivity enabled by CODESYSUnlimited I/O points, fieldbus networks, and visualization variables for CODESYS applicationsCODESYS Visualization (Target and Web), SoftMotion and CNC/Robotics support by different packageAdvantech Data Connect (ADC) Library provides flexible and highly efficient data connection with 3rd party application software through symbols (PLC Handler) & shared memory (C++/C#)Modular Computing Box designed with Intel Atom® x6425E with one DDR4 SODIMM slot (up to 32GB)Multiple-sized front panel modules offered with P-Cap multi-touch sensor (12.1" & 19" with robust 5-wire resistive touch)
-
Product
64-Axis PCIe EtherCAT MainDevice Motion Controller
PCIe-8338
-
ADLINK PCIe-8338 is a hardware-based EtherCAT motion controller able to support up to 64 synchronized axes and over 10,000 points simultaneously. The PCIe-8338 features dedicated isolated emergency stop input (EMG), and configurable isolated high-speed digital input as not only generic sensor input but also pulsar input, with up to 1MHz input frequency. Optimum jitter control is provided in minimal cycles of 250µs to optimize synchronous I/O performance for vertical automation applications in semiconductor, electronic manufacturing, and others. The PCIe-8338 provides an out-of-shell application-ready (APS) function library to generate multi-dimensional, highly synchronized, time-deterministic event-triggered motion & I/O control. A wide range of compatible 3rd party SubDevice are easily designed with ADLINK's APS function library. ADLINK's MotionCreatorPro 2 utility is fully compliant with the Microsoft Windows environment, that allows complete EtherCAT motion and I/O configuration and function evaluation as well as compiling program download functions.
-
-
Product
Economic 4-Axis Motion Control Universal PCI Express Card
PCIE-1245E
-
Encoder input is 5 MHz for CW/CCW,P/D,AB modePulse output up to 5 MHzMemory buffer (10 K points) for trajectory planningPoint-to-point, line and E-GearHardware emergency input
-
Product
Rotary Displacement And Encoders
-
Industrial rotary encoders and length sensors that provide precision motion control feedback for processes requiring the need to measure and control speed, position and distance.
-
Product
Automation Product Software Development Kit
APS SDK
-
APS means “Automation Product Software”. APS library provides users a uniform interface to access all of ADLINK products which support it. It can cover many automation fields especially in machine automation. The most important component in machine automation is motion control. APS library was first born with motion control which co-working components such as system platform management, field bus communication function, general digital input/output, general analog input/output and various counter/timer supports are all built-in components in APS. The APS library will be an all-in-one solution in automation field of ADLINK products.
-
Product
Fanless Embedded Computers
-
Advantech Fanless Embedded Computers are embedded systems engaged in edge computing and highly suitable for remote monitoring and control. Advantech fanless pc offers diverse modular and ready-to-order I/O products to help customers maximize the resulting benefits and rapidly implement diverse applications, such as motion control, machine vision, and rolling stock.
-
Product
Intel Atom® IPC Controller
AMAX-7570 V2
-
Optimized BIOS & Embedded OS for 1ms real-time control (Windows and Linux)Achieve 32-axis motion control with 500 μs EtherCAT cycle time under LinuxOPC UA and Modbus TCP/RTU as IT connectivity enabled by CODESYSEtherCAT, PROFIT, Ethernet I/P, CANopen as OT connectivity enabled by CODESYSUnlimited I/O points, fieldbus networks, and visualization variables for CODESYS applicationsCODESYS Visualization (Target and Web), SoftMotion and CNC/Robotics support by different packageAdvantech Data Connect (ADC) Library provides flexible and highly efficient data connection with 3rd party application software through symbols (PLC Handler) & shared memory (C++/C#)Intel Atom® x6425RE (1.9GHz) processor with 8GB DDR4 memoryPort isolation for 8 x DI, 8 x DO, 2 x COM
-
Product
Motion Controllers
-
Curtiss-Wright Defense Solutions
Motion control systems for defense applications must be two things - accurate and reliable. As the brains of these systems, motion controllers are responsible for ensuring all other system components are just that, no matter the conditions.
-
Product
Distributed Single-Axis Motion Control Modules for Mitsubishi, Yaskawa and Panasonic
MNET-MIA
-
ADLINK's Motionnet products provide system integrators with a simple configuration and reduced wiring method for a cost-effective solution for motion applications utilizing multiple single axes. With this new concept of direct plug-in modules, the amount of space used and the amount of wiring required is greatly reduced from traditional terminal board connections.
-
Product
Embedded Peripherals
-
Elsoft’s Embedded Peripherals Systems Group has more than 10 years' experience designing, developing and integrating embedded systems. With a comprehensive portfolio of turnkey embedded systems, embedded platforms, PC based I/O modules, motion controllers and software products, and engineering services, the Group supplies innovative technologies to OEMs and automation enterprises worldwide.
-
Product
IC-3121, 1.91 GHz Intel Atom Quad-Core Processor, 2-USB3 Port Industrial Controller
784961-01
-
1.91 GHz Intel Atom Quad-Core Processor, 2-USB3 Port Industrial Controller - The IC‑3121 is a compact and rugged industrial controller that withstands the harsh environments common in automation, supervisory control, distributed control, and industrial embedded OEM applications. The IC‑3121 offers two USB3 ports with dedicated bandwidth, FPGA-based I/O capabilities, and network connectivity for distributed control applications. The advanced features include the ability to synchronize image inspection results with industrial I/O and configure hardware-timed network triggers to trigger camera acquisition, motion control, or data acquisition. You can use the advanced FPGA personality that is shipped with the system or customize the FPGA functionality using the LabVIEW FPGA Module.
