-
Product
Flexible Waveguide Assemblies
-
CAES provides an extensive portfolio flexible waveguides, waveguide assemblies, subassemblies of components, and assemblies in packages specifically designed to meet all of your requirements.
-
Product
Ultra Fine Flexible Microprobe
IT-24P
-
IT-24P Ultra Fine Flexible Microprobe - Tiny, 24 gauge polyurethane coated wire with polyester insulated thermocouple bead. For research applications to measure temperature in animal brains and other tissue. Fairly fragile, but very fast responding.
-
Product
Flexible MiniPCI to MiniPCI Express Adapter
SKU-054-0X
-
The Flexible MiniPCI to MiniPCI Express Bus Adapter (Adapter) was designed to convert a standard MiniPCI bus into a MiniPCI Express bus. It allows you to connect a MiniPCI Express board (half-size or full-size) to a motherboard that has a standard 124-pin MiniPCI connector.The Adapter includes a MiniPCI Express adapter board (downstream), MiniPCI host board and PCI Express flat cable.
-
Product
Circuit Breaker Finder Accessory Kit
69411
-
For use with ET300 Digital Circuit Breaker Finder.Light socket adapter for finding the correct circuit of a lighting fixture.Alligator clip adapter enables use of on bare wires.
-
Product
Flexible Cable Set, 2.4 Mm To 3.5 Mm
85134F
-
The Keysight 85134F is a 62.9 cm (24.75 in) long1 flexible cable set composed of a 2.4 mm female2 to PSC-3.5 mm female connector and a 2.4 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss greater than or equal to 16 dB. Insertion loss is 0.31 * sqrt (f) + 0.2, where f is frequency in GHz, for the test port connector and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is specified with a 90 degree bend using a 4 to 3 inch radius. Stability1 of the Keysight 85134F is less than 0.12 dB and phase is 0.13*f+ 0.5°, where f is frequency in GHz.
-
Product
Get Flexible, Get FlexiFLASH
LatticeXP2
-
*Up to 885 Kbits sysMEM™ embedded block RAM and up to 83 Kbits distributed RAM*sysCLOCK™ PLLs up to four analog PLLs per device that enable clock multiply, divide and phase shifting*Three to eight sysDSP blocks for high performance multiply and accumulate.*Pre-engineered source synchronous IOs for DDR/DDR2 up to 200 MHz and 7:1 LVDS interface support up to 600 Mbps*Available in csBGA, TQFP, PQFP and BGA packaging
-
Product
Flexible AC/DC Current Tester
FCM-400
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Bending free flexible clamp sensor*Measuring ranges AC/DC 0.100A～300A(Min. resolution 0.001A)*Big CT window (φ450mm)*Easy accessibility to the hard to clamp object
-
Product
Digital Display Auto Circuit Tester
1676
-
Peaceful Thriving Enterprise Co Ltd
This is a DC voltage tester with smart over-voltage protection and warning for vehicle repair. As electrical system for vehicle becomes more complex, the tester is able to test voltage value, identify DC polarity from different background light color, positive / negative sign, and over-voltage level indication. Moreover, the special designed probe is able to help user to hook, piercing, and probing the wires.
-
Product
Medalist i1000D Small Foot Print Inline and Offline In-Circuit Systems
U9405A
System
Unlike traditional bridge type board handlers that add a 3rd party equipment on your offline ICT systems, we provide a one-stop shopping experience when you are automating your in-circuit test.
-
Product
Comprehensive Oil Analyzer For Industrial Machinery Print
MiniLab 153
-
With four simple tests, the MiniLab 153 delivers comprehensive on-site oil analysis, providing immediate actionable results, saving time and reducing costs. Highlights of this system include:*One product, delivering lab-quality analysis outside of the lab*Simplified workflow for the non-expert user, no chemist required *Simplified operation, data reporting and report interpretation via the TruVu 360 Diagnostic Sets with recommended actions.
-
Product
Flexible Waveguide
-
Flexible waveguide sections to connect waveguide comopoents and enable different mechancial placements
-
Product
CT Tester, Meter Tester, Circuit Analyzer
GOLD MINER IV
-
Gold Miner is the first device of its type to test the electricity meter using exact, simultaneous measurements made on all primary and all secondary phases of the circuit. Perform in-service meter testing with a combined 3-phase load, or a single-phase load. Gold Miner not only displays the Meter’s accuracy, but also the overall, true accuracy resulting from the CTs + Meter combination for your entire measurement circuit.
-
Product
Advanced Circuit Card Automated Test
ACCAT
-
The ACCAT is designed to support diagnostic and acceptance test requirements across a wide spectrum of testing parameters. ACCAT provides a suite of core parametric test instruments, advanced GUI based software, Huntron Access Robotic probing and Huntron Analog Signature Analysis (ASA). ACCAT provides stimulus and asurement capabilities necessary for full functional and parametric testing of circuit card assemblies along with robotic guided probes for fault verification and debug. The Huntron ASA test is ideal for pretest or safe to power up procedures protecting the integrity of the test system.
-
Product
Finger Print Module
UTC-100P-F
Biometric Peripheral
Image resolution: 508DPI. Gray scale: 8-bit. Array size: 256 x 360 pixels. Imaging area: 18.00mm x 12.80mm.
-
Product
Short Circuit Loop Impedance Meter
AMZC-306
-
Voltage measurement up to 750V and up to 250V with resolution 0,1V ; Measurements using Uni-Schuko adapter or test wires 1,2; 5; 10 and 20m ; Loop impedance measurement with resolution 0,01Ω and much more
-
Product
Flexible Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131H
Calibration Cable
The Keysight 85131H is a 62.2 cm (24.5 in) long1 flexible cable with a 3.5 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss greater than or equal to 16 dB. Insertion loss is 0.25 * sqrt (f) + 0.2 dB (where f is frequency is GHz) for the test port connector, and 1.5 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 3 inch radius. Stability1 of the Keysight 85131H is less than 0.12 dB and phase is 0.13o * f + 0.5o, (where f is frequency in GHz).
-
Product
Flexible Automatic Measuring System Release
FAMS-R5
-
FAMS-R5 uses the system with high-speed communication, FAMS High-Speed Link2, to share data with each unit.Sensors can be directly connected to the measurement unit in a laboratory.Simple wiring and highly accurate measurement can be achieved.By adding the MCU that can calculate the control model with MATLAB/Simulink, it also supports the simulation bench.
-
Product
Digital Circuit Breaker Analyzer
CT-7000 S3
-
The CT-7000 S3 is Vanguard’s fourth generation EHV circuit breaker analyzer. The CT-7000 S3 is available with 3 (part number 9021-UC) or 6 contact timing channels (part number 9100-UC). The CT-7000 S3 can fully analyze a circuit breaker’s performance by measuring the main contact and resistor contact time, stroke, velocity, over-travel, bounce back and contact wipes. Both contact and motion analysis can be performed on all circuit breaker operations (OPEN, CLOSE, OPEN-CLOSE, CLOSE-OPEN, and OPEN CLOSE-OPEN). The CT-7000 S3’s timing window is selectable between 1 second, 10 seconds, and 20 seconds.
-
Product
Circuit Breaker Analyzer
CAT Standard Series
-
The CAT Standard series circuit breaker analyzers & timers are stand-alone or a PC-controlled digital instruments for circuit breakers condition assessments. The timing channels record closing and opening of the arcing, resistor, and auxiliary contacts. CAT Standard series records graphs of both, trip and close coil currents and displacements of the HV and MV circuit breaker moving parts. The main contact channels can also measure the resistance value of the pre-insertion resistors (if present in the circuit breaker). Test results can be downloaded to a USB memory stick or saved to internal memory. The CAT Standard series internal memory can store up to 500 test results (numerical and graphical data). Test results can also be printed on the 80 mm (3.15 inch) thermal printer (optional accessory) in tabular and graphical form. CAT Standard series provides an easy selection of different operational modes:
-
Product
Circuit Breaker Testing Equipment (SCOT Series)
SCOT MXP+
-
SCOT MXP+ measures, displays and prints CLOSE, OPEN and CLOSE-OPEN time of 2 Main + 2 PIR contacts per pole, 3 poles simultaneously, ensuring measurement of 6 Main + 6 PIR contacts simultaneously. Ideally suitable for CBs having PIR contacts & multiple breaks per pole
-
Product
Circuit Breakers
-
As the premier supplier of power system components, Interpower has what you need to complete your projects, including circuit breakers. Interpower has no minimum order requirements, plus same day shipping is available on in-stock Interpower products.
-
-
Product
120-480V AC/DC 4-way Circuit Tester
1962A
-
Peaceful Thriving Enterprise Co Ltd
*With ETL and cETL Approval.*Bright neon AC/DC indicator.*Unique features with convenient pocket up.*Check voltage on 120V, 240V, 277V and 480V AC/DC.*Individual indicator for each voltage range assures reliability.*Reinforced casing and twin flexible test leads store in housing.*The easy way to test, which you can use one hand by our unique design to test outlets.
-
Product
DIN-Rail Wiring Terminal Board With CJC Circuit
PCLD-8710
Terminal Board
Low-cost screw-terminal with 68-pin SCSI-II connectorOnboard CJC (Cold Junction Compensation) circuits for direct thermocouple measurementReserved space for signal-conditioning circuits such as low-pass filter, voltage attenuator and current shuntIndustrial-grade screw-clamp terminal blocks for heavy-duty and reliable connectionsDIN-rail mounting case for easy mountingSupports PCI-1710U/UL, PCI-1710HGU, PCI-1711U/UL, PCI-1716/L
-
Product
Flexible Implantable Microprobe
IT-18(10 FOOT)
-
IT-18(10 FOOT) Flexible Implantable Microprobe with 5 foot lead - Implantable in semi-solids and tissue with 18 gauge needle (supplied). Also for immersion in various solutions and rectal temperatures of small animals. Totally sheathed in chemical resistant Teflon™. Quited rugged. Maximum Temperature 150°C . Isolated. Probe diameter .050" (14 gauge represents the needle gauge that the probe can be inserted through). Time constant 0.3 seconds.
-
Product
Flexible Test System Automation Platform
RF2000A
-
The Ranatec RF2000A is a flexible test system automation platform that helps you to integrate your complete test system into a single box. No more cables and discrete parts on your desktop!
-
Product
PXI-5922, 24-Bit, 8MB/ch Flexible Resolution PXI Oscilloscope
779153-01
Oscilloscope
24-Bit, Flexible Resolution PXI Oscilloscope—The PXI‑5922 high-resolution oscilloscope features a flexible measurement resolution range up to 24 bits, with up to 114 dBc spurious‑free dynamic range (SFDR), and up to 15 MS/s rates. This PXI oscilloscope has flexible settings for coupling and voltage range, as well as a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. The PXI‑5922 is capable of taking extremely resolute and accurate analog measurements. It is ideal for audio signals, spectrum analysis, and other small, accurate signal measurements. The PXI‑5922 also features PXI synchronization and data streaming capabilities.
-
Product
6-48V Digital Circuit Tester
1674E
-
Peaceful Thriving Enterprise Co Ltd
Checks on 6, 12, 24 and 48V systems.
-
Product
Flexible 32-bit PCI to x1 PCI Express Adapter
SKU-049-0X
-
The Flexible 32-bit PCI to x1 PCI Express Adapter (Adapter) was designed to expand the 32-bit PCI bus into an x1 PCI Express bus. It allows you to connect the x1 PCI Express expansion board to the motherboard PCI connectorThe Adapter includes an x1 PCI Express adapter board, 32-bit PCI host board and PCI Express Flat cable.
-
Product
Circuit Breaker Identifiers
188 FFF
-
Standard Electric Works Co., Ltd
● The 188FFF doesn't have the function of the sensitivity adjustment. If the customers need the sensitivity adjustment function, plase refer to other models.● The 188FFF is a Fuse and Fault Finder which comprises of two parts : The Receiver and the Transmitter.● The Transmitter, draws a current from the mains supply circuit to which it is connected to. The Signal● Current from the Tx is at about 10kHz. The Transmitter is powered by the mains and requires no batteries.● The 10kHz signal current generated by the Transmitter is then searched(sniffed) by the Receiver to detect the Fuse, Circuit Breaker or the faulty circuit.● The Receiver is a tuned circuit which has it's center frequency tuned to about 10kHz. The sensor is located in the tip of the Receiver.● The amplitude of the received signal is shown on a bar-graph type Leds.● The more Leds ON, the stronger the signal.
