Fiber Optic Test
See Also: Fiber Optic, Fiber Optic Cable Test
-
Product
Quad Optical Loss Test Set
KI27624-INGAAS-APC
-
A Quad Optical Loss Test Set used to test power, insertion loss, continuity and faults on multimode and single mode fiber with an APC connector at 850 / 1300 nm & 1310 / 1550 nm. In a small package, it provides a powerful solution to improve test flexibility and productivity.
-
Product
Optical Fiber 32×1 Switch
OFSW - 32 × 1
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 32×1 is a 32×1 prism optical switch. It can support 32 optical fibers input and 1 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
Product
Optical & RF Test Equipment Repair and Calibration
-
Custom Calibration Solutions, LLC
We are the only commercial repair lab in the country capable of fixing major problems with optical test equipment including OSA's, Tunable Lasers, Attenuators and Optical Wavelength meters.
-
Product
In-Line 2-Module In-Circuit Test System; i337x, Series 5i
E9988E
In-Circuit Test System
Short wire fixturing eliminates problems commonly found with long wire fixturing, such as noise and deterioration of test stability. This translates into transportable, repeatable and stable tests on your i3070 Series 5i, even if you need to deploy tests halfway across the globe, or on different manufacturing sites.
-
Product
Fiber Optic Communications
-
Fiber optic converters are installed between the end of fiber optic cables and data loggers to provide a lightning-proof connection.
-
Product
Accessory, Fiber Optic Contacts, Cleaning Kit
910121170
Cleaning Kit
Accessory, Fiber Optic Contacts, Cleaning KitPlease note- This product cannot be shipped internationally and may only be shipped within the continental United States. Material Safety Data Sheets are available for two products in this kit. Click the red links below to download.This kit contains: Micro Duster Pressurized Air Canister Isopropyl Alcohol 4 oz Spray Bottle 2.5mm Wrapped Swabs, 5 Pack 1.25mm Wrapped Swabs, 5 Pack Cleaning Wipes (1 Box, 286 count) Isopropyl Alcohol Pre-Moistened Wipes, 50 Pack Connector Cleaner Cleaning Kit Case
-
Product
Fiber optic active antennas / field probes
EFS-105
-
The EFS-105 is the first in a family of fiber-optic active antennas & E-field probes. The field distortion caused by the probe head is nearly zero due to the exceptionally small probe head and the all-optical signal transmission and power supply. This gives an invaluable advantage for near field measurements and measurements close to metallic parts.
-
Product
Mini Fiber Optic Receiver
MX555 series
-
The Maxcom MX555 series optical receivers are versatile, low-cost and compact optical receivers are versatile, low-cost and compact optical receivers for use in HFC fiber applications.
-
Product
Fiber Transceiver Modules
-
Optical transceiver (transmitter and receiver) modules convert data signals to and from laser optic light and plug into routers, switches, and fiber host bus adapters (HBA). They provide the transmission of data between transceivers over fiber or optical cables.
-
Product
Two-Way Optical Loss Test Set
KI23427OLF-INGAAS-APC
-
A Two-Way Optical Loss Test set (OLTS) that's perfect for medium to ultra high fiber count loss, length and optical return loss testing applications on single mode fiber with an APC connector at triple 1310 / 1490 / 1550 nm. A pair of these compact instruments set new standards of productivity, accuracy and ease of use. The 650 nm VFL is on a separate port.
-
Product
Fiber Optic Strain Sensors
-
Opsens Solutions optical strain sensor delivers reliable results in harsh environment. Opsens Solutions OSP-A fiber optic strain transducers are designed to provide accurate deformation measurement in the most adverse conditions. Its small size and EMI/RFI electromagnetic environment and lightning immunity makes it the ideal sensor for geotechnical, structural health monitoring, Defense and aerospace and general applications.
-
Product
Fiber Testing Kit
KI-TK056
-
1310/1550 nm source & power meter, Interchangeable SC connectors
-
Product
PXI/PXIe MEMS Optical MUX, 4-Channel, Multi-Mode, 50/125 Fiber, SC/PC Connectors, With Interlock
42-850A-214-M50-HI
Multiplexer Module
The 40/42-850A-214-M50-HI is a PXI/PXIe 4-channel multiplexer with SC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
In-Circuit Test System
TestStation LX
Test System
TestStation LX is a cost-effective in-circuit test solution providing high-volume electronics manufacturers with reliable, high-quality test for the latest printed circuit board assembly technologies.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber, FC/PC Connectors, With Interlock
42-852A-118-M62.5-HI
Multiplexer Module
The 40/42-852A-118-M62.5-HI is a PXI/PXIe 8-channel multiplexer with FC/PC connectors, includes hardware interlock and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Optical Radiation Safety Test
EN62471-C
-
IEC62471-2006(CIE S009) Photobiological Safety of Lamps and Lamp System and IEC TR62471-2(2009) Guidance on Manufacturing Requirements Relating to Non-laser Optical Radiation Safety have be published addressing hazard to human (mostly eye and skin), and are completely suitable to assess the optical radiation safety of non-laser sources, such as LED products, UV radiation in general lighting products and etc.
-
Product
Optical Fiber 1×13 Switch
OFSW - 1 × 13
-
Hangzhou Huatai Optic Tech. Co., Ltd.
OFSW- 1×13 is a 1×13 prism optical switch. It can support 1 optical fibers input and 13 fiber output, channel switch. Wide operating wavelength range, low insertion loss and speedy switching rate, can use network trends configuration, network monitor and lab application.
-
Product
Bare Fiber Aligner
1120
-
The Photon Kinetics 1120 Bare Fiber Aligner makes it possible to reduce test setup time to seconds, thereby reducing overall testing cost. Just strip the fiber, scribe and break it (or use a more precise fiber cleaver, if desired) and then insert the prepared end into the 1120. In an instant, the fiber is coupled to your OTDR or chromatic dispersion test system with low optical loss and low reflectance. The 1120's compact, ergonomic industrial design is well-suited for low to moderate volume fiber and cable testing applications where automated fiber alignment systems are less economical. It is particularly useful as part of an in-process or finished cable test station employing either the 8000i or 8000 OTDR, and the OASYS.net OTDR Automation Software.
-
Product
Optical Tensiometers
Theta Topography
-
Theta Topography is an innovative system capable of separating the effect of surface roughness to the contact angle result. As a result, roughness-corrected contact angles can be better compared with each other for research and quality control purposes.
-
Product
Dispersion Compensation Optical Fiber Module
DCM-G.652-C-Fxx
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai and DCM-G.652-C-Fxx dispersion compensation fiber module, is negative dispersion compensation based on optical fiber technology, can effectively compensate for G.652 standard single-mode fiber transmission band of 1525 ~ 1565nm dispersion and dispersion slope characteristic.
-
Product
Fiber Patch Cables
-
Wuhan Sunma Technology Co., Ltd.
SunmaFiber Patchcord and Pigtails is suitable for enterprise network, telecom room, server farms, cloud storage networks, and any place fiber jumper cables or pigtails are needed. It meets RoHS compliant, and cable is optically tested for insertion loss to ensure high quality.SunmaFiber supply fiber optic patch cord, fiber optic patch cable,LC,SC/APC,ST,E2000/APC,MU,VF45,FC, MT-RJ, SC, MPO, Volition, MTP, FC/APC, ST/APC, LC/APC, E2000, DIN, D4, SMA, Escon, FDDI, RoHS compliant, LSZH, Riser, Plenum, OFNR, OFNP, simplex, duplex, single mode, 9/125, SM, multimode, MM, 50/125, 62.5/125.
-
Product
COM Express Type 7 10GbE Optical Fiber Network Adapter Card
10GbE Optical Fiber Network Adapter Card
Network Interface Controller
- Supports up to four 10GbE optical fiber interfaces (SFP+)- Compatible with PICMG COM.0 R3.0 Type 7 modules
-
Product
Optical Sensors
-
Many measurements are much easier to make with light. Southern Photonics designs and manufactures optical sensor systems for a wide range of applications including gas sensing and strain sensing.
-
Product
HDMI Extender via One SC Multimode Fiber Optic Cable to 3,280 feet
ST-FOHD-SC50
-
The XTENDEX® HDMI Extender via Fiber Optic Cable locates an HDMI display up to 3,280 feet (1,000 meters) away from a video source using a single SC multimode fiber optic strand. Each extender consists of a transmitter that connects to a video source and a receiver that connects to a display.
-
Product
Ytterbium-doped Fiber Amplifier
YDFA
-
Ytterbium-doped Fiber Amplifier (YDFA) is another Amonics specialised product line. Like our highly recognized optical amplifiers, the YDFA offers high output power and high gain with exceptional reliability. ideal for high power YDFA applications. The turnkey microprocessor controlled benchtop YDFAs manage alarms and status indicators. An integrated RS232 or Ethernet computer interface enables easy control, diagnostic functions and data acquisition. Available options include single frequency operation, linearly polarized operation.
-
Product
Audio Fiber Tracer
CFT-810
-
Motorized Polarization Controller. In addition to its basic function of adjusting polarization states in multi channels, it also provides convenient ‘save and recall’ functions. As a Scanning PC, it provides very powerful ‘auto scan’ modes with variable scanning speeds. Polarization states can be manipulated by either manual adjustment or remote control (GPIB, RS-232) using two quarter-wave plates in each channel of the PC1600. Additionally, the auto scan mode of FIBERPRO’s Motorized Polarization Controller has been upgraded in LPC, and it shows another auto scan mode of four quarter-waveplates with higher polarization extinction ratio when connecting two channels at a high speed. PC1600 is an essential tool to complete fiber-optic, multi-channel measurement systems such as WDM/DWDM as well as R&D (i.e. PMD experiments), and manufacturing.
-
Product
Pro Optical Loss Test Set
CertiFiber
-
The CertiFiber Pro Optical Loss Test Set improves the efficiency of fiber optics certification. The Taptive user interface simplifies set-up, eliminates errors and speeds troubleshooting. A set reference wizard ensures correct reference setting and eliminates negative loss errors. Built on the future-ready Versiv platform, CertiFiber Pro Optical Loss Test Set (OLTS) provides merged Tier 1 (Basic) / Tier 2 (Extended) testing and reporting when paired with OptiFiber Pro module.
-
Product
Optical Profilometers
-
Profilm3D® and Zeta™ optical profilometers provide fast, easy, non-contact solutions for 3D surface topography measurements. Our portfolio of optical profilers supports a variety of measurement techniques, including white light interferometry, True Color imaging and ZDot™ confocal grid structured illumination. KLA Instruments can help guide you to the right optical profiler solution for your unique needs.
-
Product
Pulsed Fiber Amplifier
MOPA
-
These light sources are compact Master Oscillator - Power Amplifier (MOPA) structures that can be directly modulated in a defined operating range of repetition frequency and pulse power. The standard products operate in the wavelength range around 1.5 µm at a repetition frequency > 6 kHz and a pulse energy of 10 µJ/50 ns (200 W peak power).
-
Product
Fiber Geometry System
FG500
-
The FG500 is a fiber geometry system that measures the physical dimensions of the fiber including core, cladding, and coating diameter, non-circularity, and eccentricity. The FG500 is designed to produce accurate measurements quickly and with confidence.
