EM Simulators
models and predicts the character of electromagnetic fields.
See Also: Electromagnetic Simulators, EM Simulation
-
Product
3-DOF Simulation Table
KRD60 series
-
KRD60 Series 3 DOF simulation table simulates various mechanical, electrical, and electronic products installed on ships, seaplanes, and other equipment to perform sway and tilt tests to determine the ability and structural integrity of the product to withstand severe sway and tilt requirements. The tilt test is mainly applicable to large-angle tilt caused by ship damage, manipulation, imbalance in loading and unloading, and wind. The sway test is mainly applicable to long-term swaying of the ship due to external forces such as wind and waves, which must be maintained normally or products that work reliably, and products that have a significant impact on their performance in a rocking environment.
-
Product
Ray tracing and Laser Simulation / Cavity Design Software
LasEasy V1.0
-
LasEasy software is the professional software for simulating and designing solid-state laser cavity, optical amplifier system, and parametric OPO systems. It can also simulate the laser light propagation in both horizontal and vertical (sangital and tangitial) planes.
-
Product
MEMS Sensor Simulation
SimSENSOR
-
Performance testing of sensor fusion in MEMS inertial and multi-GNSS navigation systems. SimSENSOR extends the capabilities of Spirent’s multi-GNSS simulators by simulating MEMS sensor outputs on a common trajectory with the simulated GNSS RF signals. The simulated MEMSs sensor outputs include user control of representative noise and errors (bias/drift).
-
Product
ELECTRIC BRAKE FORCE METER WITH DYNAMIC LOAD SIMULATION AND CIRCUIT TESTING
MDTT9107
-
*Tests truck-side brake controller output and all towing-lighting functions without a trailer*Displays real-time brake controller output gain and timing*Quickly troubleshoots electrical circuits and ground condition*For use with aftermarket and integrated brake controllers*Microprocessor controlled; simulates trailer brake loads*25' cable allows one-man, in-cab testing of brake controller and all truck-side tow circuits*Use to verify that the vehicle’s adaptive (speed/load sensitive) brake-controller output is functioning properly
-
Product
Basic Rate and Primary Rate ISDN Network Simulator
Emutel Duo
-
Emutel Duo is a convenient and flexbile basic rate and primary rate ISDN network simulator. With 3 software selectable S/U interfaces and optional 2 E1/T1 interfaces you can test and develop a full range of ISDN equipment.
-
Product
Portable Solar Simulator
XES-40S3
-
We have manufactured the highly accurate solar simulators, which is used for evaluations where sunlight needs to be recreated. By fully utilizing these technologies, we have developed this portable Solar Simulator, which can easily reproduces sunlight. Our device is optimum solution for initial evaluations and inspections for the research purpose.
-
Product
Virtual Platform Simulation Acceleration
QuantumLeap
-
QuantumLeap is a parallel simulation performance accelerator that leverages a new synchronization algorithm to provide the fastest virtual platform software execution speed available. The execution performance of this new technology has been measured on average at 15 times faster than the nearest commercial solution using standard benchmarks.
-
Product
24 Channel Isolated Counter / Totalizer & 16 Channel Pulse Simulator
DP-cPCI-5004
-
DP-cPCI-5004, Isolated Pulse Simulator / Counter / Totalizer module is an integrated module for pulse output, pulse measurement and event counting. The module has 16 isolated channels of pulse output at desired frequency. The 16 channels are divided into three groups . The first two groups have four differential and one single ended channels each.
-
Product
ARINC 429 Test And Simulation PMC Module
PMC-429
PMC Module
*4, 8, 16 or 32 software programmable TX / RX channels*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*PXI interrupts, star trigger, and PXI clock*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Sorting according to SDI field*VXI Plug & Play driver including soft front panel*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
Product
ESD - Simulator
SESD 230
-
The test generator SESD 216 simulates electrostatic discharge as defined in the standard IEC / EN 61000-4-2. Depend on the Equipment Under Test (EUT) and the test set-up for laboratory tests the IEC standard shows two test methods
-
Product
3D Electromagnetic Simulation Software
XFdtd®
-
A full-featured simulation solver, XFdtd outpaces other methods in efficiency as the number of unknowns increases. XF includes full-wave, static, bio-thermal, optimization, and circuit solvers to tackle a wide variety of applications, including antenna design and placement, biomedical and SAR, EMI/EMC, microwave devices, radar and scattering, automotive radar, and more. It also works with Remcom's ray-tracing products to provide thorough simulation capability at the low-, middle-, and high-end of the electromagnetic spectrum.
-
Product
PXI Analog Output/Thermocouple Simulator - 32 Channel, ±100mV
41-761A-001
Thermocouple Simulator
The 41-761A-001 is a 32-channel low voltage output module ideal for simulating the operation of a thermocouple. It is part of a range of modules available with a choice of 32, 24, 16 or 8 channels. Each channel provides a low voltage output across two connector pins capable of providing ±20 mV with 0.7 μV resolution, ±50 mV with 1.7 μV resolution and ±100 mV with 3.3 μV resolution, covering most thermocouple types. For applications that require slightly higher voltages, there are also options that provide up to 250 mV, 500 mV, 1000 mV, 1500 mV and 2000 mV.
-
Product
O-RU Simulator
-
With Simnovus’s web interface, there is no need to install any software to use the UE simulator.The UE simulator has an intuitive step-by-step workflow to walk users through the generation of even the most complex test profiles in just a few minutes.
-
Product
Network Emulation, Delay Simulation, Bandwidth Emulator & WAN Simulation
-
GigaNet System’s network emulation appliances provide precision, performance and predictability in your test infrastructure resulting in optimized system performance and robust system behavior under real world network conditions.
-
Product
2 Port T1/E1/PRI ISDN Simulator
SIM-2PRI
-
The most inexpensive ISDN simulator on the market. This unit has two PRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network.
-
Product
Optical Components & Transmission Simulation Software
VPIphotonics Design Suite
-
VPIphotonics Design Suite™ embeds expert knowledge from our component and transmission design tools in one shared, flexible software environment to support requirements in design, analysis and optimization providing you with the most powerful numerical algorithms tailored for your applications.
-
Product
2 PRI + 16 BRI-S/T ISDN Simulator
CH-16BRI-ST-MOD-2PRI
-
This unit has two PRI ports and 16 BRI ports allowing ISDN equipment to be connected together just as if they were connected through the ISDN network
-
Product
Non-Invasive Blood Pressure Simulator
SC-5 SimCube® NIBP
-
The STANDARD SC-5 SimCube® NIBP Simulator provides ECG, Respiration, Arrhythmia, Pacer Simulation, IBP and three Digital Manometer Modes of tests.
-
Product
Waveform Generation Toolbox for Wideband Signal Simulation
N7509A
-
The Waveform Generation Tool provides a simplified interface for baseband modulation of Keysight's wide bandwidth signal simulation solutions, for signals with up to 1 GHz RF bandwidth. Even the most complex signals are defined and implemented easily through the software interface. Signals can be defined through basic parameter entry or from files created in MATLAB or other engineering environments. For each selection in the main menu, a subsequent screen appears, enabling the user to enter the parameters required to define the waveform and invoke the built-in calibration routines. A display on each sub-panel shows the ideal frequency domain waveform calculated from entered parameters. A simulation mode is provided to enable development and operation without connection to the instrument hardware.
-
Product
IBP Simulator
IBPS 2.0
-
The IBPS 2.0 is a PC controlled simulator to replace real IBP sensors. Originally designed for IEC 60601-2-34 testing, it can also be used by manufacturers to play their own test signals or database recordings.
-
Product
ARINC 429 Simulator & Analyzer Applications Software
F-SIM-A429
-
Avionics Interface Technologies
Software GUI Application for Operating AIT ARINC 429 InterfacesCapture & Analyze Data from Multiple ARINC 429 Input ChannelsDefine & Execute Complex Simulations of Multiple Rate-Oriented Labels - Simulate Output Data on Multiple Channels Simultaneously - Replay Previously Captured Bus Data - Full Error Injection & Detection - Update, Modify, & View ARINC 429 Data on-the-fly - Engineering Unit Displays & Software Widgets - Receive Data to Label/SDI Specific Buffers - Also Supports MIL-STD-1553, ARINC 664, Ethernet, & Data Load operations
-
Product
Seal Integrity Verification and High Altitude Shipping Simulator
SIV III
-
The SIV also has the ability to simulate shipping a packaged box of dry goods at high altitudes. The number of peaks, the heights of the inclines (or peak), the ramp speed (or rate), and the time at the peak are configurable through the controller.
-
Product
Highly Collimated Solar Simulators
-
This solar simulator is based on a Fresnel lens to collimate the light beam from the arc lamp source to infinity, which results in highly collimated illumination of the target spot. A 2.5kW xenon ozone free lamp is used as the light source. The spectral distribution of the xenon light source, along with the use of specially calibrated AirMass filters, closely simulates the sun’s true spectral distribution in various conditions on Earth.
-
Product
Precise Testing & Simulation of A2B® Networks
A2B®-Component-Tester
-
The Automotive Audio Bus (A²B®) is a bus developed by Analog Devices Inc. for infotainment systems in automobiles. It is increasingly being used in other applications such as AV conferencing systems. Typical A²B® -products are Hi-Fi amplifiers/speakers, head units, eCall systems, microphones, vibration/noise suppression units, actuators, or sensorsCommunication happens via a simple two-wire UTP (Unshielded Twist Pair) cable. All A²B® -components are connected in a master/slave architecture to form a network. The complexity of audio systems in these A²B® -networks is reduced, and with it the cost and weight.
-
Product
Dual Channel Gigabit Ethernet Test & Simulation Instrument for XMC
XMC-DCE
-
Avionics Interface Technologies
Dual channel, high precision Ethernet Test Instrument
-
Product
Electronic Circuit Simulator
SimOne
-
SimOne lets you perform full-featured electronic circuit simulation using state-of-the-art and classic modeling algorithms while taking full advantage of modern computers.SimOne does all the basic circuit analyses common to SPICE modeling systems and as well provides important Stability analysis.
-
Product
Single, Dual Or Quad Stream MIL-STD-1553A/BTest And Simulation Modules For XMC
AXC1553-x
-
MIL-STD-1553 Test and Simulation modules for XMC with 1, 2 or 4 dual redundant streams plus 8 Discrete I/O’s (on Rear-I/O).*Concurrent BC, MRT (31) & Chronological/Mailbox Bus Monitor*Full Error Injection/Detection (AS4112)*Complex Triggering, Data Capture/Filtering and 100% Bus Recording*Physical Bus Replay*IRIG-B Time Encoder/Decoder*Full Function, Single Function and Simulator Only versions available*Drivers for Linux and Windows*Drivers for other embedded applications are available on request*Optional Databus Test and Analysis Software and RT Production Test Plan
-
Product
Lightning Impulse Simulation Tester
KT-6030iG
-
Most of all electric systems and equipments are weak against the lightings(direct, inductive lightning). In fact, those electric equipments are broken mainly by lightning.This Lightning Impulse Simulation Tester is certificated to IEC 61000-4-5, and generates the similar impulse with huge rush currents and tests the safety of the power systems and equipments.
-
Product
PXI Analog Output/Current Loop Simulator Module - 16 Channel
41-765-001
Analog Output Module
The 41/43-765-001 is a PXI/PXIe 16-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Solar Simulator for Multijunction Solar Cells
-
For series connected multijunction cells, at a given spectrum (e.g. AM 1.5 or AM 0 for space solar cells), one of the cells will limit the current in the series connection of cells. All solar simulators deviate from the true AM 1.5 spectrum, and they are only classified in wide spectral bands (100nm width). So even for class A or A+ solar simulators, it can easily happen that the bandgaps of the multijunction cells are such distributed that the 'wrong' cell will limit the current, if a solar simulator with fixed spectrum is used. In the 70s and 80s, when these measurements were first developed, intercomparisons showed deviations of cell efficiency in fixed spectrum solar simulators of more than 40%.
