Electromagnetic Simulators
models and predicts the character of electromagnetic fields. Electromagnetic Field
See Also: EM Simulators
-
Product
Damped Oscillatory Wave Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
Damped oscillatory wave test system for new energy can produce repeatable transient on HV or medium voltage power cord, control line and signal line. It can meet the requirements of CE and CCC certificate. With internal three-phase five-wire high power CDN DOPN 69100T, it can conduct new energy test and high power load test with good reliability, stable performance and easy operation.
-
Product
MIMIC® IOS Simulator
-
MIMIC IOS Simulator is a command line simulator that fully supports Cisco IOS® software as well as NX-OS, JUNOS, NETCONF, other command line interfaces and SNMPv1, v2, v2c, v3. You can simulate up to 100,000 devices in a single workstation, and an unlimited number of devices can be simulated by distributing it over multiple workstations. You can access devices using Telnet, SSH and SNMP. Changes made using one protocol is reflected in the other.
-
Product
MIL-STD-1553 Test & Simulation Instrument for VXI
VXI-1553
-
Avionics Interface Technologies
Dual redundant, multi stream configurations availableSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Real-Time recording and physical bus replayANSI Application interface supporting C, C++, C#, and .NET development - VISA based VXI “Plug & Play’ Device driver provided
-
Product
Solar Simulator for Multijunction Solar Cells
-
For series connected multijunction cells, at a given spectrum (e.g. AM 1.5 or AM 0 for space solar cells), one of the cells will limit the current in the series connection of cells. All solar simulators deviate from the true AM 1.5 spectrum, and they are only classified in wide spectral bands (100nm width). So even for class A or A+ solar simulators, it can easily happen that the bandgaps of the multijunction cells are such distributed that the 'wrong' cell will limit the current, if a solar simulator with fixed spectrum is used. In the 70s and 80s, when these measurements were first developed, intercomparisons showed deviations of cell efficiency in fixed spectrum solar simulators of more than 40%.
-
Product
Battery Simulator
G5.BAS
-
The G5.BAS series is bidirectional regenerative. It was developed specifically for the simulation of energy storage devices and batteries and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BAS series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3.
-
Product
Resistor Simulation Card
SET-1210
-
The card has two ranges of values that meet the requirements of most functional test systems.The SET card is designed for applications in which resistive sensors provide information about parameters such as temperature (e.g. when testing motor controls)Each channel of the SET-1210 resistor simulation card is able to simulate the common short-circuit and no-load conditions, which can occur in a system due to faulty wiring or sensors.
-
Product
Battery Cell Simulation / Emulation
BMS
-
Efficiency, reliability and safety of modern lithium ion batteries for electric vehicle drives strongly depend on the battery management system (BMS) as their electronic control unit.
-
Product
Single or Dual Stream MIL-STD-1553A/B Test and Simulation Module
APE1553-x-DS
-
A unique feature of AIM’s APE1553-x-DS modules is the option for the MILScope™ capability. Models APE1553-1-DS/APE1553-2-DS integrate an onboard Analogue to Digital Converter (ADC) which samples, measures and stores the MIL-STD-1553 waveform. Automatic waveform validation is performed by the users Application Software or in conjunction with AIM’s PBA.pro Databus Test and Analysis Software and Test Scripts.
-
Product
Simulation And Analysis Software
fcXplorer Analyzer
-
Avionic Interface Fiber Channel Simulation and Analysis Test Software, fcXplorer, is an easy-to-use graphical user interface for Fiber Channel Simulyzer modules. fcXplorer is designed for troubleshooting, optimization, planning and configuration of fiber channel data. The low and high level protocol analysis offers acquisition, filtering, time stamping and interpretation of Fiber Channel data traffic and generates statistics.
-
Product
ARINC 429 Simulator & Analyzer Applications Software
F-SIM-A429
-
Avionics Interface Technologies
Software GUI Application for Operating AIT ARINC 429 InterfacesCapture & Analyze Data from Multiple ARINC 429 Input ChannelsDefine & Execute Complex Simulations of Multiple Rate-Oriented Labels - Simulate Output Data on Multiple Channels Simultaneously - Replay Previously Captured Bus Data - Full Error Injection & Detection - Update, Modify, & View ARINC 429 Data on-the-fly - Engineering Unit Displays & Software Widgets - Receive Data to Label/SDI Specific Buffers - Also Supports MIL-STD-1553, ARINC 664, Ethernet, & Data Load operations
-
Product
3D/2.5D Time-Domain Electromagnetic Field Solver Software
EM-CORE ®
-
3D/2.5D Time-Domain Electromagnetic Field Solver Software for Planar-Circuit and Antenna Simulation. 3D & 2D Radiation Patterns Modeling, Spiral Inductors Modeling, 3D EM Modeling of Filters, Intuitive Geometry Build, and more!
-
Product
Resistor Simulator Card
CP-RESSIM-16
-
The CP-RESSIM-16 Resistor Simulator PCIe Card provides programmable resistance simulation across multiple channels for real-time test and validation environments. The card supports 16 independent digital programmable resistors, enabling accurate emulation of variable resistance conditions within a system.
-
Product
2 Port 10/100/1000Mbit/s AFDX/ARINC664P7 Test, Simulator And Monitor Module For PMC
AMCX-FDX-2/B
Monitoring Module
AFDX®/ARINC664P7 Test and Simulation module for PMC with 2 full duplex ports programmable for 10/100/1000 Mbit/s. Versions available for both Airbus and Boeing variants of ARINC664P7.
-
Product
One, Two, or Four Dual Redundant Interface MIL-STD-1553A/B Test & Simulation Module for PXI Express
PXIe-1553
-
Avionics Interface Technologies
1, 2, or 4 dual redundant MIL-STD-1553 bus interfaces Concurrent BC, multiple RT (31), and BM operations Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay Multi-level Trigger for Capture/Filtering IRIG-B Time Encoder/Decoder Real-Time Recording and Physical Bus Replay Application interfaces supporting C, C++, C#, and .NET development Device Driver Support for: Windows, Linux, and LabVIEW Real Time (others provided on request) 10 high voltage (up to 30V) programmable DIO lines Flight Simulyzer GUI Analyzer software
-
Product
10 Gigabit Ethernet Test & Simulation Instrument for PXI Express
PXIe-10GE
-
Avionics Interface Technologies
Supports 10G and 1G Full Duplex Ethernet2 Network Interfaces (future expansion to 4 network interfaces)User controlled Ethernet frame transmissions with high precision timing and scheduling
-
Product
Modular DC Electronic Load LED Simulator
6310/A
-
Chroma Systems Solutions, Inc.
Chroma 6310A Programmable Electronic Load integrates microprocessor capabilities into each load module and mainframe to provide simple and accurate parallel operation to optimize the speed and control among multiple load modules. All load modules may be configured to work synchronously, to test multiple outputs simultaneously, thus simulating real life applications.
-
Product
ARINC 429 Test & Simulation Instrument for VXI
VXI-429
-
Avionics Interface Technologies
Programmable High/Low Speed Operation Concurrent operation of all Tx/Rx Channels at high data rates
-
Product
Calibration Cable, 78-pin D-type, Thermocouple Simulator Modules
40-975-078-1m
Calibration Cable
This cable assembly is specifically designed to connect to the 78-Pin D-Type port on the front panel of Pickering Interfaces Thermocouple Simulator Modules 41-760 and 41-761 enabling calibration via an external DMM.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, 750 V Isolation
43-752A-012
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
PXI Analog Output/Current Loop Simulator Module - 16 Channel
41-765-001
Analog Output Module
The 41/43-765-001 is a PXI/PXIe 16-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
Product
Xenon Long Pulse Solar Simulator Three Target Sizes
-
Complies with IEC60904 Class A solar simulation standards.Up to 100ms of effective irradiated time is achieved. Through our proprietary filter technology, spectral concordance conforms to IEC / JIS Class A standards.Three systems provide a wide selection to meet your panel size, floor space, and performance requirements.
-
Product
MIL-STD-1553 A / B Test And Simulation VME Module
VME-1553
-
*Dual redundant*1, 2, 4 or 8 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*VISA based VXI Plug & Play driver*Optional twinax front end
-
Product
Capacitance Simulation Card
SET-1220
-
The SET-1220 device is a designed capacitive fuel sensor emulation for NI-SLSC. This card provides eight isolated channels that can emulate capacitance values between 10pF and 800pF. It was designed to emulate capacitive sensors that are typically connected between an excitation voltage on one end and a virtual ground on the other end.
-
Product
4-Quadrant Power Amplifier For Simulation Applicaton
PAV20000
-
PAV Series Four-quadrant Simulation Power Amplifier based on linear power amplifier technology and integrated advanced technical performance and rich functions.
-
Product
3U VPX RL Thermal Load Simulation Module
-
The 3U power test module is an ideal solution for evaluating heat dissipation in a rugged conduction cooled VPX cage or chassis. This card is a thermal load in the chassis to evaluate the heat dissipation. The chassis can be monitored with temp sensing probes and or FLIR imaging. Different wattages are selected by setting dip switches. The +5 and 3.3V loads are on the top of the module. The +12V and -12V loads are on the bottom side of the module.
-
Product
Solar Simulation Systems
-
Solar simulation systems with global radiation guarantee the simulation of natural sunlight according to CIE20 and CIE85 Table 4. Our portfolio includes components, systems and systems for solar simulation for test benches in the automotive, military, aerospace, railway, photovoltaic, material research and building materials industries. Our plants and systems stand for high reproducibility and precise test results.
-
Product
VLF Electromagnetics
-
VLF surveying relies on radio signals that are broadcast from navigation stations around the world. The principle is that these signals are deflected in certain ways when they pass through conductive ore or water-filled vertical-to-sub-vertial fractures in the earth. By monitoring these deflections, the position and, potentially, size of the target can be determined.
-
Product
ARINC 664 Part 7 Test & Simulation Interface for PCI
PCI-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfacesSimulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboardError Injection including Runt Frames, Short IFG, and Invalid MAC FCS - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Acceleration Simulation Mode (ASM) for Single Driven Axle Vehicles
ASM_AF | VP 230045
-
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-AF roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The ASM-AF is built into the base.
-
Product
PXI Millivolt Thermocouple Simulator Module - 32 Channel
41-760-001
Simulator
This series of PXI Thermocouple Simulator Modules is available in a choice of 32, 24, 16 or 8 channels—each channel providing a low-voltage output across two connector pins capable of providing ±20mV with 0.7µV resolution, ±50mV with 1.7µV resolution and ±100mV with 3.3µV resolution, covering most thermocouple types.
