Fixed Attenuators
Fix the degree of attenuation.
-
Product
19" Solid Fixed Storage Shelf, 30"D
SS-1930
-
Sturdy 19" shelf formed of one piece of 16 ga. CRS bolts to panel mounting rails. Supports heavy chassis or power supplies or provides storage for tools, test leads, chart paper, etc.
-
Product
Digital Step Attenuators
-
Ranatec’s digital step attenuators covers all mobile frequency bands and gives a calibrated attenuation range of more than 90 dB in steps of 0.25 dB. All Ranatec digital attenuators are built as modules and offers both serial and parallel control logic.
-
Product
Bench Power Supply, Single, Adjustable, Fixed, 3 Output, 0 V, 30 V, 0 A, 3 A
72-6628
-
The 72-6628 is a Triple Bench Power Supply with adjustable current control and galvanized steel case. The DC regulated power supply is a completely solid state, compact, well regulated, constant voltage power supply suitable for service field, hobby, laboratory and testing use. It provides three different voltages output for different. Overload and short-circuit protection, prevent the unit from overload and short circuit. When the unit is under the condition of overload or short circuit, the output current will be limited. Independent 5V, 12V easy snap-on output terminals to make it easy to use for TTL and CMOS circuit testing. The grounding of the output terminals is independent that the output can be connected in series to make a higher output voltage.
-
Product
Low-Cost, Fixed Focus, An-alogue High Definition Camera
L3C-AHD
-
The Teledyne Bowtech L3C-AHD is a low cost, fixed focus, An-alogue High Definition Camera. The analogue HD signal will travel up to 250 metres on a Teledyne Bowtech coax or a high quality screened twisted pair (a small inline mould is required to be connected between the camera and the umbilical when a screened twisted pair is used). The video is viewed on an HD monitor with an HDMI connection after going through a small topside converter box.
-
Product
Digital Control Step Attenuator
-
RF Lambda’s digital control step attenuators are used to fine tune an RF signal using TTL control lines. Fast response time, various step sizes and overall attenuation ranges make these suitable for a variety of RF applications. Hermetically sealed options are available upon request.
-
Product
Fixed Mounting Panel, G2, 5U, 3 Position, (2 Blank Plates Included)
310113395
Mounting Panel
The 19" rack mounting panel offers three mounting positions for the G2 receiver without the hinging feature and is beneficial in cases where you may want to restrict wiring or instrument access.
-
Product
Fixed Gas And Leak Detectors
-
Fixed Gas Detectors are installed to provide continuous, area, and personnel protection around the clock. The detection system is designed to alert workers of the potential danger of poisoning by toxic gas exposure. Fixed gas detectors are generally installed in large facilities and are used to both detect major leaks and as an early warning of gas leaking from a particular system.
-
Product
Chip-Type Attenuators
-
Panasonic Industrial Devices Sales Company of America
Chip-Type Attenuators for high-frequency signal attenuation, level adjustment or matching improvement.
-
Product
Fixed Mounting Frame, iCon, 1U, 2 Positions, Black Anodized
310113488
Mounting Panel
This iCon 2 position fixed mounting frame is 1U in height and is anodized in black. iCon cover plate sold separately (310 113 490).
-
Product
Electric Servomotor Fixed Torsion Tester
-
This tester series is one of the fastest standardized products among electric servomotors Torsion Fatigue / Durability Tester for various materials and automobile parts .
-
Product
Fixed Magnification Interferometer
FiBO 250
-
FiBO 250 offers a solid and economical solution to automated fiber testing by bringing together full 2D visual inspection capabilities and true phase-shifting interferometry to achieve exceptionally accurate measurements. A fixed focal length 10x magnifier ensures maximum system stability and a very high level of repeatability.
-
Product
24" Solid Fixed Storage Shelf, 24"D
SS-2424
-
Sturdy 24" shelf formed of one piece of 16 ga. CRS bolts to panel mounting rails. Supports heavy chassis or power supplies or provides storage for tools, test leads, chart paper, etc.
-
Product
(100×130×19mm) C-Band DWDM FGA Full Function Module Fixed Gain EDFA Module
FGA4400-FM04
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai FGA4400-FM04 series is a fixed gain Full Functional EDFA module which is specifically designed for C-Band DWDM optic transmission system, accord with various communication technology requirements of 44 channels DWDM system. It adopts nowadays excellent optical performance, advanced electronic control technology and complete software functionalities. Excellent total integration electronic transient control technology ensures amplifier to achieve the locking of optimal flat gain (OFG) in large dynamic input optical power range.
-
-
Product
Fixed Digital Gas Detector
OLCT 10N
-
Teledyne Gas & Flame Detection
The OLCT 10N is a digital combustible gas detector designed for to detect combustible, toxic gases or oxygen. Intended for use in combination with the MX 16, MX 32 and MX 43 controller, the OLCT 10N provides a fast and accurate response.All transmitter information is received by the controller in less than 1 second.Non-intrusive operator interface requires only a simple magnetic wand and allows one man calibration without opening the enclosure.
-
Product
Fixed Power Analyzers
-
Network analyzers are devices that are essential for measuring electrical parameters and controlling industrial processes. They provide the user relevant, real-time information for managing energy consumption and checking the quality of supply and consumption in their installation. They offer multiple communication options, inputs and outputs to manage any alarm that may appear in the installation, and provide analyses and reports on the performance of their network.
-
Product
NI-5191, 800 MHz, ±30 V, 10X Attenuation, Differential Active Oscilloscope Probe
781785-01
Oscilloscope
The NI-5191 is a differential, active voltage probe that offers 800 MHz of input bandwidth with a 10:1 attenuation ratio. You can use it with oscilloscopes that provide 50 Ω input impedance. You can power the probe using a Type-N barrel power connector from a USB port or using a 9 V alkaline battery.
-
Product
Voltage Variable Attenuators To 16 GHz
-
Our family of voltage controlled attenuators is non-reflective, with ranges of 32 dB of 64 dB. Pin diodes are used and the frequency range is 0.25-16 GHz. They operate with a control voltage of 0 to +8 VDC and handle +27 dBm maximum input power. These attenuators are bi-directional: either SMA port may be used for an input.
-
Product
Power/Voltage Rail Probe. 4 GHz Bandwidth, 1.2x Attenuation, +/-30V Offset, +/-800mV
RP4030
-
The Teledyne LeCroy RP4030 Power Rail Probe meets the specific requirements of those who need to acquire a low-voltage DC signal as part of a:-Comprehensive power integrity, digital power management IC (PMIC), voltage regulator module (VMR), point-of-load (POL) switching regulator, or low-dropout regulator testing- Complete embedded power management system that includes PMICs, VRMs, POLs, and LDOsThe RP4030 will faithfully acquire a low-impedance, low-voltage DC power/voltage rail signal without unduly loading the device under test (DUT), while providing high offset to allow DC power/voltage rail signal display on an oscilloscope with high gain.
-
Product
Fixed Mounting Panel, iCon, 4U, 8 Positions, Painted Gray
310113301
Mounting Panel
This 4U Fixed Mounting Panel has 8 vertical positions. The iCon cover plate is sold separately (310113467). The spacing of the positions will accommodate ITA P/N's 410123102 and 410123232. Also available in black anodized finish - P/N 310113302.
-
Product
Attenuator
RFATT AXIe-0
-
*Dual channel AXIe attenuator with frequency range from 9 kHz to 10 GHz.*The module is designed to work as part of information measuring systems as a normalizer of radio frequency signals (power control: signal amplification or attenuation).
-
Product
Handheld Variable Optical Attenuator
VOA100
-
Shanghai Tarluz Telecom Tech Co., LTD
VOA100 handhold optical variable attenuator is used for continuously variable optical signal attenuation. As the VOA100 is used in the laser system for the on-line testing, therefore, it can be used in the digital system of communication devices (such as: PHD, SDH) and also in the system of adopting analog modulation (CATV)
-
Product
Fixed Gas Detectors
DG7 Series
-
Teledyne Gas & Flame Detection
All DGi-TT7 are constructed from a common housing and electronics with the detection properties being determined by the type of sensor (cartridge) used. A wide range of cells are available, these cells are intrisically safe protected, and may be replaced with the detector powered which minimises the system down time. The intelligent, microprocessor driven unit is fully configurable using a wireless hand-held terminal (TLU) or by using the hard wired HART option giving true flexibility to the installer and reduced service costs.Elements such as relay operation and alarm levels are all set via the TLU, a hazardous area approved hand-held unit. The unit may be interfaced directly with a wide range of panels, controllers and PLC’s etc. Its integral daylight readable alphanumeric display indicates local status and alarm level.
-
-
Product
Programmable Step Attenuator, DC to 4 GHz, 0 to 11 dB, 1 dB steps
8494G
Attenuator
The Keysight 8494G dc to 4 GHz programmable step attenuator offers exceptional repeatability and reliability. Attenuation is provided in 1 dB steps from 0 to 11 dB. Precision gold-plated leaf springs ensure long-life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. A maximum switching time of 20 ms (including contact settling) speeds automatic testing. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
-
-
Product
Manual Attenuator (Waveguide)
-
RF Lambda’s manual waveguide attenuators are used to control signal levels using a manual control knob. These are commonly used in test setups or systems where an operator is present and there is a need to change signal levels manually.
-
Product
Fixed Wavelength CW Laser Source (DFB)
Laser 1200 Series
Laser Source
The Laser 1200 Series is a highly customizable fixed-wavelength Continuous Wave (CW) laser source available in a wide range of wavelengths and powers.With seamless PXI integration, it can be easily integrated into new or existing PXI test setups. Save space, lower your costs and improve testing efficiency while delivering reliable and repeatable results in production or research environments.
-
Product
Source - 20 GHz Source with Amp Attenuator
RI8554A
-
Automated Instruments, Powerful Development Tools and Worldwide Support
-
Product
Attenuator Interconnect Kit, 3.5 mm
11716E
Interconnect Adapter
The 11716E attenuator interconnection kit provides the necessary parts to connect 84904K and 84906K programmable step attenuators in series.
