CV
-
Product
Vacuum Chambers
CV 400/CV 250
-
The CV 250 and CV 400 are vacuum chambers for altitude flight simulation for avionics instruments such as altimeters, rate of climb indicators and all non pressurised equipment. They are fitted with pneumatic and electric connectors and a quick locking door.
-
Product
Software
Quasi-Static Measurements
-
Materials Development Corporation
The Quasi-static measurement ompares a high frequency capacitance-voltage plot to a C-V plot measured near zero Hertz (quasi-static). By analyzing the difference in the depletion region of the curves, the interface trap density (Dit) can be determined in the sample under test.
-
Product
High Power DC Electronic Load
33500F Series（2.4KW~14.4KW）
-
33500F Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store/Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface. SHORT time setting and SHORT_VH, SHORT_VL setting function, also can measure Short Voltage and Current.
-
Product
DC Electronic Load
3310G Series（75W~400W）
-
Each 3310G Series module has its own control and display panel, CC / CR / CV / CP / Dynamic modes, plug in 3302G / 3305G / 3300G mainframe with 150 sets Store / Recall memory which provides load set-up more efficiently, also can be controlled via RS232、Ethernet、USB and GPIB interface.
-
Product
High Power DC Electronic Load
34000A Series（5KW~40KW）
-
34000A Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.SHORT time setting and SHORT_VH, SHORT_VL setting function, also can measure Short Voltage and Current.
-
Product
High Power DC Electronic Load
36000A Series（50KW / 60KW）
-
36000A Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.SHORT time setting and SHORT_VH, SHORT_VL setting function, also can measure Short Voltage and Current.
-
Product
Semiconductor Device Parameter Analyzer and Measurement Modules
B1500A Series
-
Keysight B1500A Semiconductor Device Analyzer of Precision Current-Voltage Analyzer Series is an all in one analyzer supporting IV, CV, pulse/dynamic IV and more, which is designed for all-round characterization from basic to cutting-edge applications. It provides a wide range of measurement capabilities to cover the electrical characterization and evaluation of devices, materials, semiconductors, active/passive components, or virtually any other type of electronic device with uncompromised measurement reliability and efficiency. In addition, the B1500A’s modular architecture with ten available slots allows you to add or upgrade measurement modules if your measurement needs change over time.
-
Product
Electronic Loads
-
PeakTech Prüf- und Messtechnik GmbH
Can be used for important test procedures in quality assurance as well as e.g. testing of power supplies and control units, batteries, fuel and solar cells. For precise load control for various purposes, this device offers load control according to constant voltage (CV), constant current (CC), constant load resistance (CR) or constant power (CP) with a highly precise resolution of 1mW, 1mV, 1mΩ and 1mA. The device also offers additional test modes, e.g. the battery test or the dynamic test. The PC interface and software offer the option of implementing freely programmable test sequences with data evaluation.
-
Product
Mini Digital Clamp Tester (CE)
M-140HC
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Easy!:Measurale Load Current at high voltage CV/CVT cables with grounding lines for shield phase.*Epoch-Making!:Can measure phase current of CVT cable just by putting CT head on to the conductors as well as CV cable just by clamping CT to the conductors in a lump.*Low Cost!:Can measure line/leakage current in the same manner as ordinary clamp meters.
-
Product
OLED Lifetime Test System
58131
Test System
The 58131 Lifetime Test System is designed specifically for the OLED industry. Model 58131 provides twoquadrant constant current (CC) and constant voltage (CV) stimulus to each OLED panel and acquires electrical and optical characteristics automatically. Two independent and isolated precision source-and-measure units (PMU) are incorporated in one modular card, which is capable of testing two OLED panels. Additional instrument cards are added to expand test capacity. Hot plug and play is a key feature of 58131. When a UUT fails or an instrument card needs to be replaced, 58131 does not have to be shutdown and testing continues for other UUTs. Hot plug and play obviates life test cycle restarts due to isolated faults and significantly improves life test efficiency. We firmly believe that hot plug and play capability should be mandatory for all lifetime test systems.
-
Product
QS603 60V/3A Power Supply
-
*16 hours at full load*Low ripple and noise*Automatic switching CV / CC*Aluminum heat sink*Displays 3 or 4 digit depending on the model
-
Product
Semiconductor Switching Systems
Keithley 700 Series
-
The high speeds and low currents of semiconductor devices demand high quality, high performance switching of I-V and C-V signals. We offer switching solutions for both semiconductor R&D and production test applications with mainframes that can support up to 2,880 channels and a family of matrix cards designed specifically for semiconductor applications.
-
Product
High voltage Flexible range Regulated DC Power Supplies
PSF-H Series
-
* Main Applications: High-voltage capacitors or relays used for hybrid cars, electric cars, solar power system and high-voltage LED lighting equipment.* 6 times of flexible output range: PSF-800H covers output for several units of conventional type regulated power supplies within 800W ( max voltage 800V, max current 6A. ).* Constant Power Control: CP mode is available in addition to CV and CC modes.* Changeable setting style: Vertical or horizontal setting by 90rotating panel.* Sequence Operation: Stand-alone sequence is available with the insidememory programmed by PC, through the optional control board (IF-60GP, IF-60RU).* Master-slave parallel operation: Possible to increase the output current by master-slave parallel connection of the same model (up to 2 units).* Various functions are available: Output OFF timer, 3-point preset memory, Remote sensing, External analog control, OVP/OCP/OHP protections
-
Product
Bench Power Supply, Adjustable, 2 Output, 0 V, 32 V, 0 A, 3 A
72-8690A
-
The 72-8690A from Tenma is a dual channel general DC power supply suitable for laboratory use. The dual channel (CH1 and CH2) can work in CV or CC mode and these two modes convert automatically according to the load. The CH1 and CH2 have auto tracking function. In this condition, the output of CH2 tracks the output of CH1. This function is usually used when adjustable symmetrical and double polarity power is required. Both CH1 and CH2 display the output voltage or current with a 6 digit LED meter. The main outputs can be connected in parallel or in series. This product comes with 2 years warranty.
-
Product
Single Channel Linear DC Power Supply
MPS-D+ series
-
Voltage stabilitySource effect CV≤0.01%+2mVLoad effect CV≤0.01%+2mVRipple and noise CV≤1mV(rms）CC≤5mA(rms）Voltage temperature coefficient 150ppm/°CCurrent stabilitySource effect CC≤0.2%+2mALoad effect CC≤0.2%+5mACurrent temperature coefficient 500ppm/°C
-
Product
LED Driver Aging Rack
LEDRACK-100W192P
-
• Application range: LED driver and multi channel driver power aging. It has equipped with computer operation and monitor system. The working condition can be set by the computer, and the computer will record real time data to do statistical analysis. • The parameters of load can be set freely on the software, to monitor the real time voltage, current, and power etc • Load mode: CC, CV, CR, CP, and LED • Aging Control System includes: ON/OFF control signal output; Signal of relay switch control; K type thermocouple temperature acquisition • The channels are parallel connected under arbitrary load mode, which can allow product power expansion • The LED Driver Aging rack will design according to customer’s LED driver power and aging quantity per time • Automatic current switching function (optional) • AC power meter to measure modules, and test power input characteristics (optional) • Temperature monitoring function at product zone (optional) • PWM dimming and two sets of logic control signal function (optional)
-
Product
Controllable, Programmable Linear DC Source
LAB / S
-
*Linear laboratory power supply*High quality DC sources with the lowest residual ripple*CV / CC mode with LED display*Protection against short circuit, overload and overtemperature*Optional IEEE 488, RS232, analog interfaces*3-phase input optional
-
Product
High Power DC Electronic Load
34000C Series（6KW~24KW）
-
34000C Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.
-
Product
Power Supplier QS305 30V / 5A
-
*16 hours at full load*Low ripple and noise*Automatic switching CV / CC*Aluminum heat sink*Displays 3 or 4 digit depending on the model
-
Product
LED Load Simulator
63110A/ 63113A/63115A
Simulator
As shown on the V-I curve in figure 1, the LED has a forward voltage VF and a operating resistance (Rd). When using a resistor as loading, the V-I curve of the resistor is not able to simulate the V-I curve of the LED as shown in blue on figure 1. This may cause the LED driver to not start up due to the difference in V-I characteristic between the resistors and the LEDs. When using Electronic Loads, the CR and CV mode settings are set for when the LED is under stable operation and therefore, is unable to simulate turn on or PWM brightness control characteristics. This may cause the LED driver to function improperly or trigger it’s protection circuits. These testing requirements can be achieved when using a LEDs as a load; however, issues regarding the LED aging as well as different LED drivers may require different types of LEDs or a number of LEDs. This makes it inconvenient for mass production testing.
-
Product
Software
Conductance Measurement and Analysis
-
Materials Development Corporation
MDC uses conductance to give a complete picture of MOS devices as well as to correct for series resistance effects. MDC C-V plotters use conductance and capacitance measurements to plot true device capacitance and depletion region conductance.
-
Product
PathWave IC-CAP BSIM3 Model Extraction Package
W7024E
-
The W8553EP IC-CAP BSIM3 Model Extraction Package provides complete measurement and extraction procedures for DC, CV and RF model parameters. The intuitive, Windows-style user interface enables engineers to quickly produce an accurate model.
-
Product
Reference Electrodes
-
Reference electrodes are widely used as: electrochemical measurements (CV, LSV, DPV, etc.) electrochemical devices (detectors for HPLC, biosensor, etc.)
-
Product
Software
Junction Measurement and Analysis
-
Materials Development Corporation
A comprehensive set of analyses for junction diode or Schottky barriers begins with C-V data gathering that adjusts the voltage step to the slope of the C-V characteristics. This assures an optimum set of C-Vdata whether the voltage range is small or large. Doping profile and resistivity profile are both available at the touch of a key. Plots of 1/C2 - V or Log(C) - Log (V+ phi) show doping uniformity and doping slope factor. Exclusive recalculation options allow adjustment of stray capacitance and area to facilitate calibration using a standard reference wafer of known doping or resistivity.
-
Product
DC Electronic Load
3310G Series（800W）
-
Has its own control and display panel, CC / CR / CV / CP / Dynamic modes, with 150 sets Store / Recall memory which provides load set-up more efficiently, also can be controlled via RS232、Ethernet、USB and GPIB interface
-
Product
Multi-output AC Power Supplies (CV/CF)
PCR-LE2 Series
-
The PCR-LE2 Series are designed based on the PCR-LE Series that supports single-phase output, single-phase 3-wire output, and three-phase output within the rated capacity by selecting the switch from the front panel operation.The PCR-LE2 series offer the same basic performance, using the common power unit of the PCR-LE Series, with providing easier installation and saving the space more efficiently compare to the individual allocation of the system for a single phase, single-phase 3-wire, and three phase systems. The lineup of PCR-LE2 Series are available in 5 models:6 kVA, 9 kVA, 12kVA, 18kVA, and 27 kVA model.
-
Product
High Speed-Large Current DC Electronic Load (CC/CV/CR/CP)
PLZ-4WL Series
-
While the PLZ-4WL series succeeds to the superior operability of our conventional model of the PLZ-4W series, the PLZ-4WL series realizes the high speed rise and fall time (slew rate of 50A/µs.) in the range of low voltage with large current. The PLZ-4WL offers six operation modes, and equips with various features such as sequence operation, switching operation, soft-start function, and time and voltage measurement. The PLZ-4WL applies not only for the conventional load test of the CPU power supply, but also it can be applied to even faster current response test. In addition, the PLZ-4WL is a space-saving design (about 50% less volume of the conventional model) that can save the facility space of the testing site, and it can be applied for the single cell testing of the large scale rechargeable battery.
-
Product
Programable Power Supply & Programable Electronic Load
EL-820P
-
*Digital button control and easy operation*High resolution(20mV, 10mA, 0.1W, 0.1Ω)*Overload prevention function*9 sets programmable memory*4 sets real time display*Voltage range: 1V~63V*Current range: 10mA~15A*Maximum power: 200W*Operation mode: CV, CC, CP and CR*Built in USB interface
-
Product
6kW Regenerative DC Electronic Load (CC/CR/CV/CP/CC+CV/CR+CV)
PLZ6000R
-
PLZ6000R is a DC electronic load that regenerates load power to the AC line. Regular electronic loads consume load power by having semiconductor devices convert it into heat. By contrast, PLZ6000R converts load power into reusable electric power, rather than converting it into heat as is typically done, and feeds this power to the AC line, thereby substantially reducing the amount of waste energy. PLZ6000R is an environment-friendly electronic load that can contribute significantly to your energy saving efforts.
-
Product
Ferroelectric Test System
LCII
-
Precision LC II is an affordable Ferroelectric Tester for research labs. This system offers 5Khz at 9.9V and also comes in a built in 10V, 30V, 100V, and 200V option. This unit can also be expanded to 10kV for bulk ceramic testing. Vision Software is provided with the LCII Test System. Vision uniquely allows the user to construct complex or simple programs with any number of tests to characterize all aspects of the sample in one execution while keeping track of the measurement results and the history of the sample being tested. Tasks such as Hysteresis, I/V, C/V, PUND, Waveform, Magnetoelectrics, Piezoelectrics are just a few features to choose from.
