Electrical Testers
-
Product
Radome Tester
QAR50
-
The R&S®QAR50 is the ideal tool for accurately testing the quality of automotive radomes and bumpers in the automotive radar frequency range at the end-of-line (EOL). It features sufficient space to easily accommodate bulky bumpers combined with spatially resolved measurements to evaluate the homogeneity of design emblems.
-
Product
In-Circuit Tester
Eagle MTS180
-
The Eagle offers low testing cost for high volume with even the most complex fixture applications. Equipped with a Press-Down-Unit and a combination of analog and hybrid In-Circuit test pins, the MTS180 is in a class for its own. Furthermore, the tester can be equipped with functional test modules to provide even higher fault coverage and thus satisfy the test requirements of a larger number of customers.
-
Product
120 GBd High-performance BERT
M8050A
Bit Error Rate Tester (BERT)
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
Product
DIP Tester
Model DS-10
-
Putting it a conveyor to flow through a solder bath to obtain information needed to manage it. The created temperature profile makes it possible to monitor the 50ms sampling temperature of the preheat and solder temperature sensors in addition to the conventional management items.
-
Product
LED Testers
-
PeakTech Prüf- und Messtechnik GmbH
An extremely practical component tester for LEDs and other components. The device outputs an automatically raised output voltage between 0 to 300 V DC, which adapts to the connected load so that the sensitive components are not destroyed. Particularly suitable for the service and repair workshop.
-
Product
Leak Tester
LSD-01A
-
Jinan Leading Instruments Co., Ltd.
LSD-01A Leak Tester is applicablein leak testing of pouches, bottles, pipes, cans and boxes of foodstuff,pharmaceutical, medical, daily chemistry, automotive, electronic components, stationary and other industries. It’ s also applicable in the leak testing ofthe specimens after falling tests and pressure resistance tests.
-
-
Product
Memory Tester
SP3000
-
CST is proud to offer a portable stand alone and affordable memory tester, combining DIMM and SODIMM testing capability all on the same universal base unit with optional easy plug-on test adapters.
-
Product
HD-TVI Tester, HD-CVI Tester, AHD Tester
M-IPC-300 series
-
Fuzhou Metricu Technology Co Ltd
4 inch IP camera tester
-
Product
Bond Tester
Sigma Lite
-
Sigma lite is a low cost of ownership bond tester that grows with your company. It gives you a low-cost entry point without sacrificing performance to meet future demands.
-
Product
Zipper Tester
-
TESTEX Testing Equipment Systems Ltd.
Zipper Tester, to determine the resistance to reciprocation of zipper (slide fastener), the test specimen is subjected to a specified number of cyclic operations whilst under lateral and longitudinal tension. Zipper Tester complies with BS 3084, CNS -1083, QB/T2171-1995, etc. Please contact us for more about information about pull test procedure.
-
Product
Electric Servo Motor Type 3-axis Vibration Tester
-
The Electric Servomotor Vibration Test System Is A New Vibration Test System Developed Based On The Control Technology Of AC Servomotors That We Have Cultivated Since Its Establishment.
-
Product
Torque Tester
DI-4B-25
-
For daily inspection of small impact tools. Since the display uses an LED, the numbers can be read clearly even in dark places
-
Product
Continuity Tester
TE6-0721
-
Hangzhou Tonny Electric & Tools Co., Ltd.
Do-it-yourself. Tests circuits with power "OFF". Reliable and economical. Requires one AAA battery for use. Battery NOT included.
-
Product
BIP Tester
-
BIP TESTER is a measuring device designed for users that already have a unit injector test bench, but their lack reliable BIP measurement.
-
Product
Electrical Networks Control System
-
Electrical networks control system is intended for measurements of network electrical resistance and insulation electrical resistance of the tested specimen. The measurement process takes a couple of minutes.
-
Product
Electrical
-
This category covers test equipment required for electrical performance tests on Industrial Lighting, Street Lighting, Automotive Lighting, Appliances, Accessories & related products. A wide range of Electrical Test Panels, Electro-mechanical endurance test systems for many products, Appliance test systems and also a range of low energy spot welding machines (one of the very few products we make which are not test equipment). Equipment are custom built to suit specific customer requirements.
-
Product
Scratch/Shear Tester
3025
-
The Elcometer 3025 Scratch/Shear Tester is used to test the resistance of many materials to scratching, shearing, gouging, marring, scraping and engraving.
-
Product
Capacitor Tester
MIG0603CAP
-
The MIG0603CAP consists of two circuits with impulse capacitance 20 µF and 0,25 µF. Both circuits generate a voltage wave shape 1,2/50 µs and are combined in a 4 unit height 19" rack. The generator circuits are defined in IEC 60384-14 and EN 132400. The serial resistors Rs, the impulse capacitor CT, and the load capacitance Cp will be automatically switched when different capacitance ranges are selected on the MIG0603CAP.
-
Product
Surge/Impulse Testers
-
specifically designed to perform the Input Test on PV Panels in accordance with IEC 61730-2, Para. 10.5.3. The output is in accordance with the published waveform from 800-10000V peak (open circuit).
-
Product
Multifunction Meter for Electrical Installations
AMPI-530
-
Measurement of short-circuit loop ; Testing of differential, general and selective protections for differential current ; Measurement of insulation resistance ; Up to 10GΩ ; Voltages: 50 V, 100 V, 250 V, 500 V, 1000 V ; Measurement of earth resistance ; Bi-directional continuity test on PE cables, phase sequence ; Measurement and recording of voltage, frequency, alternating current, cosϕ, power, harmonics and THD
-
Product
Receptacle Tester
RT500
-
Designed to detect the most common wiring problems in standard 120V receptacles.Test for correct wiring, open ground, reverse polarity, open hot, open neutral, hot and ground reversed.Conditions NOT indicated: Quality of ground, multiple hot wires, combinations of defects, reversal of grounded and grounding conductors.Large light indicators for greater visibility.Reinforced prongs for increased durability.Push-pull design with slip-resistance ribbing.Made in USA of U.S. and imported parts.
-
Product
Cellular Tester
IQxstream-5G
-
This high performance, comprehensive non-signaling tester is ideal for both 5G user equipment (UE) & small cell testing across multiple cellular technologies including 2G, 3G, 4G & 5G.
-
Product
Multifunction Electrical Installations Meter
MPI-520S
-
The MPI-520S multifunction meter is dedicated to perform diagnosis of electrical installation according to IEC 61557 standards. Digital meter MPI-520S is designed to measure impedance of a short cicuit loop also without triggering RCD, parameters of RCD, insulation resistance, earthing resistance, continuity and also for phase sequence testing. Furthermore to measure and logging of AC voltage and current, frequency and power.
-
Product
PoE Tester
PE-100
-
The PoE Tester/Power Monitor is designed for testing standard PoE and measuring power of PoE systems, by performing both PSE (Power Source Equipment) detecting and PSE/PD (Powered device) inline testing. Compliant with IEEE802.3 af, 802.3at standard and 802.3bt ultra 4-pair up to 60W-100W. PSE detecting display PoE type (af or at), power source (Endspan or Midspan) and perform a load test for voltage drop with REV LED indicates a reversed power. Inline PSE/PD testing-measure and display in rotation between voltage (Volts), current(Amps) and power(Watts) via dual 4 digit 7 segment LEDs which provides voltage available, current flowing and how much power an PD actually need ensure sufficient power for PD to make the PoE is sustainable.
-
Product
Tension Testers
-
Tension testers come in a variety of options. Lever-operated testers allow for quick and repeatable tension testing, making them ideally suited for measurement in high-throughput environments. The wheel-operated tensions tester allows for more precise control, which is critical whenever testing delicate materials. Our motorized tension tester provides consistent test speeds providing more accurate and repeatable results.
-
Product
Prodution Testers
Effitest E50
-
Effitest e50 is a flexible and cost efficient solution with easy programming, debugging of test programs and life-cycle support.
-
Product
Electrical Circuits Control Device
ZET 452
-
ZET 452 is an automated module for electrical circuits parameters control that is used for electrical circuits impedance and insulation resistance monitoring in automated mode. The monitoring is performed in accordance with the set participation and without participation of an operator. ZET 452 allows to reduce the time necessary for verification procedure more than in 20 times if compared with the standard measurement instruments normally used for these purposes.
-
Product
Portable Electricity Meter Testers
EE-120A-3S
-
The EE-120A-3S unit consists of a three-phase energy standard class 0.1 and current load up to 120A. The unit performs testing of all types of electricity meters using the voltages of the network. The meter error can be measured for active, reactive or apparent energy in Manual Mode or with predefined Test Plans using the keyboard and the LCD display on the panel. Maximum Demand Test, Register Test, Starting Current Test and No Load Test can be performed too. The energy standard of the system can be used without the phantom load to test meters with customer load and perform analysis of the three-phase network – with direct measurement or with optional current clamps.
-
Product
Electric Protector
KAB 15A
-
Konstar Electric Industrial Co., Ltd
The voltage is too low or too high, the electric protector will cut off the power automatically, when the new power supply, the protector will delay 10S-300S to make electrical appliance start to work on the stable state.The electric protector suitable for A/C, refrigerator, TV, computer, wash machine and other home electric appliance.
