Electrical Testers
-
product
Adhesion Testers
Adhesion testing is the best way to determine whether your films and coatings adhere to substrates the way you need them to.
-
product
Portable Electrical Management Systems
EMS-PT30C
Progressive Industries Portable Electrical Management Systems (EMS) offer quick and easy RV electrical protection. A true plug-and-play application with no installation required. You will feel secure with multi-mode surge, voltage, polarity, and lost/open neutral protection. Each unit includes a digital display, scrolling continuously through the power source information: voltage(s), current frequency, error code, and previous error code (if applicable). Additionally, the computer is driven by state of the art microprocessors.
-
product
Prodution Testers
Effitest E50
Effitest e50 is a flexible and cost efficient solution with easy programming, debugging of test programs and life-cycle support.
-
-
product
Electrical Safety Wall
AllWin Instrument Science and Technology Co., Ltd.
1. Electricity Safety Wall2. 50/60HZ3. Four detection ways4. Continuous testing
-
product
Pitot-Static Tester
PS-525
The PS-525 Pitot-Static tester is a low-maintenance digital tester that is fully portable.
-
product
Electric Motor Dynamometer
Dynamometer consists of aggressively designed rotor technology that allows for higher torque without the need for multiple rotors. Thus not only does the WB Series unit offer more pack to the punch, but the inertia of the WB Series unit stays well below the inertia of the engine being load-tested.
-
product
Electric Servomotor Packaged Cargo Compression Tester
It is a testing device that can perform compression evaluation test of packaged cargo equipped with an electric servo motor type actuator.
-
product
Mechanical Tester
NANOVEA Mechanical Tester is the most versatile nanoindenter and scratch tester capable of precisely measuring the micro- to nanomechanical properties of wide ranges of materials from thin films, coatings, ceramics and composites to polymers and bio materials via Indentation, Scratch and Friction testing. All NANOVEA Mechanical Tester models come with true feedback load control from independent load and depth sensors that provide unmatched accuracy and the highest repeatability available on the market. This technology allows a user to perform Nanoindentation and Microindentation for Hardness and Elastic Modulus Testing, Stress vs Strain Analysis, Creep and Relaxation, Loss and Storage Modulus, Yield Strength and Fatigue, Fracture Toughness and Nano-scratch & Micro-scratch for Scratch Hardness Testing, Multi-pass Wear Test, Cohesive and Adhesive Failure Testing as well as Coefficient of Friction testing, all available on one system.
-
product
RF ATE Tester
ADIVIC MP5800/MP5806
MP5800 seamlessly upgrades your existing Chroma 3380, 3650 to RF ready ATE test solution, user friendly debug tools, IOT turnkey test solution.
-
product
Mechanical Testers
Actron’s wide variety of mechanical testers includes specialty tools, compression testers, vacuum pressure gauges and advanced timing lights. All mechanical testers work effectively on most foreign and domestic vehicles, small engines, motorcycles and other recreational vehicles to save you time on inspections and repairs.
-
product
Automated Tester
With high labor costs in Europe and the US, and the surge in labor cost in Asia, automated test solutions are in demand. Automated systems also improve traceability and reduce operator mistakes.The combination of automation with high throughput test systems is perfect to extend the usage of Flying Probe Testers to mid size production/sample volumes.
-
product
Adhesion Testers
Instruments for measuring the adhesion of coatings to metal, wood, concrete and other substrates.
-
product
RV Protocol Trailer Light and Electric Brake System Tester
RVCHECK
The RVCHECK is a fast, easy, low-cost way to test RV lighting and electric braking systems. In addition to powering an RV trailer's lighting circuits for easy checking, your RVCHECK measures the current draw of the electric brake coils, and checks the break-away battery circuit.
-
product
Network Tester
PeakTech Prüf- und Messtechnik GmbH
Compact 3½-digit multimeter, developed according to the CAT III 600 V standard with integrated LAN network tester. In addition to the extensive measurement functions for voltage, current and resistance, this model has a fast-reacting continuity test with an acoustic signal and the possibility of performing diode tests. This combination measuring device is a very practical test device that easily shows the correct pin assignment of network cables by comparing a transmitter with the corresponding cable receiver using an LED. Trouble-free checking of cable passage, open, short and cross connect is possible.
-
product
Multifunction Electrical Installations Meter
MPI-525
Possible measurementsShort-circuit loop measurement:*impedance measurement with 23 A current (44 A phase-to-phase) - short-circuit resistor R=10,*measurement range: 95...440 V, frequency 45...65 Hz,Short-circuit loop measurement with resolution 0,01, in distribution network without tiggering RCD (In30 mA):*automatic calculation of short-circuit, detection of phase voltage and phase-to-phase voltage,*additional UNI-Schuko plug for automatic measurement, AGT adapter for 3 phase network measurement.Testing of general and selective RCD with the rated differential current of 10,30,100,300,500 and 1000 mA. (Type AC, A and B).Measurement of insulation resistance:*with test voltage 250 V, 500 V, 1000 V, 2500 V,*measurement range up to 10G,*automatic discharging after measurement,*automatic measurement of all resistences in 3,4,5-wire cables using optional adapter AUTO-ISO,*acoustic signals in 5 sec intervals for insulation resistance characteristic,*elapsing T1, T2, T3 times (0...600 s) form measurement of absorption coefficients (DAR, PI or Ab1, Ab2)*safety measurement - protection against overvoltage.Measurement of earthing resistance.Bi-directional testing of PE wire continuity using 200 mA current.*Autocalibration of test leads.
-
product
Micromotor Tester
Shanghai Aoboor Electric Co., Ltd.
Applicable to no-load test of DC micromotors.
-
product
Peeling Tester
BN-3
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3;Inspection standard: JB/T4279.6-2008Used to measure the film adhesion property of enameled round wires with nominal conductor diameter of 1.0mm and below;High-end SCM control is used;Set arbitrarily the number of twist;LED would automatically display the number of twists;Twist counter performs accurate and reliable counting;High-strength steel scraper would complete sample scarping at once, easy to operate and use.
-
product
FPD Tester
2918
The 2918 FPD tester provides 8k Super Hi-Vision (7680x4320/ 8192x4320) for testing Full 8k@60/120 Hz resolution (32/64 lane V-by-one) is supported by one tester.
-
product
VGA in Tester
M-IPC-520B
Fuzhou Metricu Technology Co Ltd
Analog camera testIP camera test, support onvif, 4K, H.264 and H.2658MP TVI test, 8MP CVI test, 8MP AHD testVGA input, support 1920 x 1200P 60FPS
-
-
product
Robotic Electric Screwdrivers
NFA-Series
Engineered for automation and robotic torque applications, the NFA-Series robotic electric screwdrivers feature a high performance brushless motor design that provide durability and reduce the common maintenance costs associated brush type electric screwdrivers. The durable automation tools deliver reliability and precision torque control at every turn. The assembly automation tools ensures accuracy with a precision automatic shut-off clutch once the preset torque is achieved in the fastening process. The NFA tools are ESD safe, ensuring less than 1 Ohm at the bit tip. ESD management in power tools ensures product quality, cost savings and a reduction in overall ESD failures. Engineers involved with microelectronic products are aware of the importance of controlling Electrostatic Discharge (ESD) failures. Lapses in preventing the occurrence of electrostatic discharge can affect production yields, manufacturing costs, product quality & reliability, reputation and profitability.
-
product
Flame Burning Tester
DRK3024A
Shandong Drick Instruments Co., Ltd.
It is used to detect high temperature resistance, combustibility and combustion performance of materials.
-
product
Mechanical Tester
TriboLab CMP
Leveraging over 20 years of CMP characterization expertise with its predecessor product (Bruker CP-4), TriboLab CMP brings a complete set of capabilities to the industry-leading TriboLab platform. The resulting accuracy and measurement repeatability enables the highly effective qualification, inspection, and ongoing functionality testing required throughout the CMP process.
-
product
Dielectric Strength Tester
HY
Chongqing Lushun Scientific & Technological Development Co., Ltd.
The instrument is designed and made as per the National Standard GB/T 507 "Test Methods for Breakdown Voltage of Lubricating Oil". It can be widely used to determine dielectric constant of lubricating oils in the field of railway, aviation, power plant, petroleum industry, and scientific institutes.
-
product
Cable/Harness Tester
IST-380
IST Information Scan Technology, Inc.
THE IST MODEL 380 is a portable, stand-alone cable/harness tester for testing any cable up to 128 points. It detects opens, shorts, and miswires within one second by comparing the test result with the golden file or the data learned from a sample good cable. The error messages can be shown on the LCD display or printed out on a printer with the correct wire list needing reworking.
-
product
LCRZ Tester
DU-6218
Delta United Instrument Co., Ltd.
Wide Measuring Range & High accuracy 0.1%Zeroing Offset FunctionProvided HI/LOW limit and BIN Sorting comparator function, to meet your needed.100 sets of memory, can be saved test parameter and comparator setting, easy to use.Cover up free, system firmware upgrade can be update via RS-232, easy to maintenanceEasy Test Condition Setting with Auto Parameter Selection & Auto Ranging Function High speed FADC, max. test speed up to 55 meas./sec, faster your automation equipment240*64 Graphic LCD display, can be read the reading clearly and easier.User friendly programmable interface, easy to useProvided RS-232C and Handler combinatorial interface option, to meet your needed
-
product
Yarn Count Tester
TESTEX Testing Equipment Systems Ltd.
Yarn Count Testing Machine, automatically calculates count systems used for sliver, roving and yarn, and can also be used for fabric yield. Yarn Count Tester consists of an accurate electronic balance with a capacity of 400g or 200g x 0.001g and built-in calculating program. Please contact us if you want to know more about yarn count test method.
-
product
Clamping Force Tester
KRD102
KRD102 series clamping force tester is an indispensable test method for improving products into high-quality fields. It is suitable for research, development, quality control and manufacturing of electronics, electromechanical, optoelectronic, automotive, toy, packaging and other industries. It can simulate the situation that the goods in the container are clamped when they are transported from the container to the warehouse. Whether the goods are damaged due to the clamping, so as to evaluate the anti- clamping ability of the packaging.
-
product
Digital Insulation Testers
This professional Voltage Insulation tester is designed with voltage overload protection and high voltage indicator to safely measure voltage in 50V, 100V, 250V, 500V,1000V and 2500V. It has a dual display when measuring under Insulation Resistance, it simultaneously show the selected voltage range and insulation resistance measured reading. These measurements can be use to evaluate insulation integrity. This troubleshooting tool is a quality control measure at the time a piece of electrical equipment is produced and an installation requirement to help ensure specifications are met and to verify proper hookup. It also use as a periodic preventive maintenance task.
