High Voltage Testers
-
Product
Adhesion Tester
-
An adhesion tester measures the force required to detach a coating from a substrate. Often called a pull-off adhesion tester or peel tester, an adhesion tester applies a large amount of force to evaluate a coating's bond strength. When measuring peel force or adhesiveness, the nature of the substrate's surface plays a significant role. However, a high-quality adhesion tester features a self-aligning measuring head to compensate for any surface irregularities.
-
Product
Dual High Voltage Power Supply Tester
MS 1110
-
DHVPS Tester is used to test and service the dual high voltage power supply units. High Voltages of range from 4KV to 11KV can be tested.
-
Product
Density Tester
LD-LDMT-A10
-
LabodamLD-LDMT-A10density tester is simple and compact. The control box adopts humanized design and the control switch adopts light-touch mode. The instrument is designed and made as per ASTM D1298 “Test Methods for Density of Petroleum and Liquid Petroleum Products (Densimeter Methods).
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-131-HI
Programmable Resistor Module
The 40-230-131-HI (PXI) and 42-230-131-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 3.5Ω and 13.6kΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-044-HI
Programmable Resistor Module
The 40-230-044-HI (PXI) and 42-230-044-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 1.5MΩ with 2Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Diode Tester
FEC200E
-
Frothingham Electronics Corporation
The FEC200E is an automatic computer- controlled diode and rectifier tester. It is controlled by a standard PC-compatible computer running FreeDOS.
-
Product
1kV, 25 MHz High Voltage Differential Probe Without Tip Accessories and with Auto Zero Disconnect
HVD3102A-NOACC
Differential Probe
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
Product
8 inch CCTV Tester & ip Camera Tester
-
Fuzhou Metricu Technology Co Ltd
8 inch IP camera tester M-IPC-800C with analog, HD-TVI, HD-CVI, AHD, cable tracer app with toner wand, anti-sunlight and screen protecting cover, video level meter for for analog camera, TVI camera, CVI camera, AHD camera.
-
Product
400 MHz High Voltage Differential Probe
DP0001A
High Current Probe
The DP0001A is a 400 MHz high voltage differential probe with 2 kV mains isolated or 1 kV CAT III rating designed for making accurate high-voltage power measurements required for testing today’s WBG power devices, power converters or motor drives.
-
Product
Transformer Tester
-
Delta United Instrument Co., Ltd.
Designed for comprehensive testing, including winding resistance, turns ratio, and inductance.
-
Product
Hipot Tester
STM/L
-
SafeTest Manufacturing/Luminaire (STM/L) can be used as a simple manual electrical safety tester or with varying degrees of automatic test sequencing.
-
Product
Oxygen Permeability Tester
T-OPT Series
-
Oxygen Permeability Tester - QT-OPT series is ideal for industrial application laboratory testing of material for Oxygen permeability testing for quality control, research and development.
-
Product
Multi-Channel Hipot Tester
19020
-
The hipot test is one of the major test items in electrical safety testing. All electrical components and products including transformers, capacitors, power supplies, chargers and home appliances require hipot testing.
-
Product
High Voltage Seasoning Equipment
-
This equipment is used to remove the bars that are in contact with the surface of vacuum interrupters.
-
Product
Macro Hardness Testers
-
Macro hardness is the measurement of the hardness of materials tested with high applied loads.
-
Product
Power Meter Tester
MT-3551T
-
Kongter Test & Measurement Co., Limited
It is multi-functional in field testing for power meters and metering units of all wirings. Testing functions include: metering unit and power meter. With these function, it is widely used in power utility, substation, telecom machine room and the alike for power consumption examination, circuit breakage inspection, power abnormality analyzing, asset management and industrial production management.
-
Product
Battery Impedance Tester
-
Weshine Electric Manufacturing Co., Ltd
The DC test method is adopted to simulate the actual use of the battery in a real and objective way, which can effectively eliminate the hidden dangers such as deficiency, deficiency and connection failure between batteries while measuring the internal resistance of the battery.
-
Product
Cable Tester
SS8681 Series
-
The SS8681 series cable tester is used for test and measure wire cable harness, wire harness, like as: auto cable, audio cable, power cable, network cable, telephone cable, USD cable, HDMI cable, video cable, etc.
-
Product
HiFIX High Fidelity Tester Access Fixture
-
The HiFIX lineup delivers clean waveform transmission, precision docking, and multi-DUT parallel test, with high reliability.
-
Product
Network Tester
-
ZhangZhou Weihua Electronic co.,ltd
There is nothing worse than running your drops only to learn that you have a fault in one of the cable runs. Get it right the first time, get it right by choosing and using the right LAN Cable Testers. We offer a variety of cable testers, which are a must have to quickly and easily verify the integrity of Ethernet twisted pair cables. Our LAN testers will test twisted pair cables for open pairs, shorted pairs, reversed pairs, crossed pairs and split pairs. Network cable testers vary in complexity and price, but a basic tester consists of a source of electrical current and a measuring device. After that, cable testers vary in complexity and ability to do various testing.
-
Product
High Voltage Probes To Measure Primary Waveforms With A Power Analyzer
Volt Litewire
-
The Litewire is a true RMS meter designed for use by electric utilities to sense currents or voltage waveforms from the primary side of their distribution networks.
-
Product
High Temperature Thermometer
SensyTemp TSH200
-
High temperature combustion, annealing and melting processes are usually executed without pressure at temperature up to 1800 °C (3272 °F). As a result, the selection of the appropriate thermowell is the greatest challenge for temperature measurement.
-
Product
Battery Testers
-
Memory & Read FunctionRight Device to know the TRUE -LIFE of Battery Capacity (Resistive / Voltage) Simultaneously MeasureOn - Line Testing without shutting down batteryBuilt - in Comparator FunctionRates Conditions as PASS, WARNING or FAILDatalogging Memory FunctionCompact and lightweightRS-232 Interface & SoftwareAuto Power Off
-
Product
PoE Testers
-
The Essential Tool for Installing and Maintaining NetworksThe LanMaster 35 is a new handheld tester used for installing and maintaining Local Area Networks (LAN) using Power over Ethernet (PoE).
-
Product
Crush Tester 350
DRK113
-
Shandong Drick Instruments Co., Ltd.
DRK113 Crush Tester 350 is a high accuracy and intelligent instrument, designed according relevant standards. The advanced components, mating parts and micro-computer are logical structured, to ensure the property and appearance. The instrument have parameter testing, adjusting, LCD digital display, memory, printing function.
-
Product
Solar Cell Testers
-
Solar Cell Testers are integrated systems incorporating Solar Simulator and I-V Measurement systems. PET offers Standard and Advance IV Measurement software. PET Cell Testers are capable of measuring a diverse range of solar cell parameters such as Isc,Voc, Imax,Vmax, Pmax, FF, Rsh, Rs and η cell conversion efficiency, complete light and dark I-V curves. All that needs to be done to test a cell is to load the cell, make electrical probes contact and press “Measure” icon on the I-V Measurement System software. The software will automatically open the Solar Simulator shutter, perform the test and close the shutter after the test is complete. The design is modular in nature and can be easily upgraded. Some options can added at a later time.
-
Product
Insulation Tester
1555
-
The Fluke 1555 insulation resistance tester offers digital insulation testing up to 10 kV, making it ideal for testing high voltage equipment including switchgear, motors, generators and cables.
-
Product
32-Ch High Voltage Relays & Multimeter
YAV90HVT
Digital Multimeter
The YAV90HVT is used as an automatic CAN bus controlled floating AC/DC true RMS digital volts/milliamps meter with built-in scanner, able to work directly in appliances and industrial mains powered electric/electronic equipment.Its powerful microcontroller allows to work as a distributed device able to data acquire, compare and return high level messages, reducing test operation time.The analog output is used as a set value for the optional high voltage programmable power supply for Hipot tests up to 1500V.The board uses Tripaddle connection modules and can operate as stand alone or be mounted on a standard Virginia Panel receiver.The board includes National Instruments LabView virtual control panel and operating software for a true Plug & Play operation.
-
Product
Electrical Safety Tester
-
PSE AG has developed an electrical safety test that combines different tests for the testing of PV modules. With our four-in-one tester it is possible to test the following according to IEC 61215-2 and IEC 61730:
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-155-HI
Programmable Resistor Module
The 40-230-155-HI (PXI) and 42-230-155-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 43.424MΩ with 4Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
