Simulation
the approximation of actual operational conditions.
See Also: Simulators, Simulation Software, Simulation Testing, Modelling, Emulation
-
Product
Temperature and Humidity Test Chambers
-
Labodam temperature and humidity test chambers are designed to simulate constant climactic conditions for testing a wide variety of products for their quality, performance, shelf life, and stability.
-
Product
PXI Precision Resistor Module 6-Channel, 2.5 to 102k
40-297-040
Programmable Resistor Modules
This 6-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
4 Port BRI-S/T-U ISDN Simulator
BRI-2U2ST
-
The unit has two S/T and two U ports allowing ISDN basic rate terminal equipment to be connected together just as if they were connected through the ISDN network.
-
Product
PXI Avionics Databus Modules
-
Avionics interface modules from Avionics Interface Technologies, offered through Keysight, enable connectivity between your PXI test systems solution to DUT’s with aviation industry standard buses. These modules are capable of simulation, monitoring, record and play back of bus traffic enabling test and verification of avionics equipment data communication capabilities. The available interface modules support industry standard avionics based buses such as MIL-STD 1553, ARINC 429, and ARINC 664p7, and Fibre Channel.
-
Product
LED Load Simulator
63110A/ 63113A/63115A
Simulator
As shown on the V-I curve in figure 1, the LED has a forward voltage VF and a operating resistance (Rd). When using a resistor as loading, the V-I curve of the resistor is not able to simulate the V-I curve of the LED as shown in blue on figure 1. This may cause the LED driver to not start up due to the difference in V-I characteristic between the resistors and the LEDs. When using Electronic Loads, the CR and CV mode settings are set for when the LED is under stable operation and therefore, is unable to simulate turn on or PWM brightness control characteristics. This may cause the LED driver to function improperly or trigger it’s protection circuits. These testing requirements can be achieved when using a LEDs as a load; however, issues regarding the LED aging as well as different LED drivers may require different types of LEDs or a number of LEDs. This makes it inconvenient for mass production testing.
-
Product
ECU Simulator
PT-LabCar
-
PT-LABCAR is an open and scalable Hardware-in-the-Loop (HiL) system. It is designed for open- and closed-loop testing of ECUs specifically in the powertrain application domain. The system can be used to run automated regression tests for the release of software variants as well as for the validation of control and diagnostic functions in early phases of ECU development.
-
Product
Charger / Quick Charger / Adapter / LED Driver Test System
6010
-
6010 Charger / Quick Charger / Adapter / LED Driver Test System is able to meet multi-types power products test requirements，and its multi-U.U.T test simultaneously capability can significantly enhance the production line throughput. It also possess multi-modular combination that includes low noise analog AC source with Triac to simulate output, four sets precision power meter, two or four sets ripple noise / timing measurement module, four sets OVP DC power supply, 3310F series & 3332F/3336F Electronic Load module and unique design 3340F series for LED power driver output test.
-
Product
IBM AT/ISA, Vectorbord Plugbord
4617-4
-
VECTOR Electronics and Technology, Inc.
98 contacts (49 each side) on 0.100" centers.Voltage/Ground Plane. Plane surfaces solder-coated for user convenience.To simulate plated-thru holes committed to voltage or groundplanes use Vector T123 eyelets. Vector T123 eyelets available separately (for use without pins). I/O mounting area for up to 70-pin D-sub and ribboncable connectors. Mounting bracket and hardware kit included (P/N HD36B).
-
Product
Component Test
-
Our innovative multi-function Electrical Component Testers have advanced functions such as voltage power control feed to activate components like radiator fan, headlights, horn, actuators, etc. and the sensor simulator can provide simulation of voltage signals, frequencies, square waves & duty signals with varying intensity to test the feasibility of good sensor signals in comparison to bad ones when troubleshooting vehicle electrical faults.
-
Product
Simulators
-
The Autonomous Air Combat Maneuvering Instrumentation System's unique combination of advanced air-to-air and air-to-ground combat training ensures air commands optimum utilization of flight hours and other valuable resources. Each system is fully customizable to address the skill sets of each operator. Key features include real-time kill weapons delivery, and electronic warfare attack notifications.
-
Product
6″ (15.25 cm) 1000W Pre-Irradiation Solar Simulator
Model LS1000-6S-009
-
1000W Pre-Irradiation Solar Simulator Kit specifically designed for the pre-irradiation step during in vitro broad spectrum sunscreen testing. Fully compliant with the most current FDA and ISO requirements. The 6″ (15.25 cm) Class A beam can irradiate up to 9 PMMA plates simultaneously.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 510 Ohm
50-293-014
Programmable Resistor Modules
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Sand Dust Climatic Environmental Simulation Test Chamber
CX-SC80
-
Shenzhen Chuangxin Instruments Co., Ltd.
Sand Dust Climatic Environmental Simulation Test Chamber
-
Product
Microwave Leakage Tester
TEK500
-
An easy to use, low cost pass / fail microwave leakage detector suitable for commercial and domestic microwave ovens. It is designed to comply with national standards on permitted exposure levels. The TEK500 includes a self test which simulates a real microwave input to ensure the unit is working correctly at all times.
-
Product
Laser Source Simulator
MT1888 Series
Laser Source
The MT1888 products are state-of-the-art Laser Source/Spot Simulators (LSS) used for the testing of laser guided munitions such as the Hellfire & Hellfire II missiles, Paveway, and the AGM-65E Laser Maverick missile.
-
Product
DC Power Supplies
-
AMETEK Programmable Power, Inc.
From benchtop supplies, modular power supplies to rack-mounted industrial power subsystems, AMETEK Programmable Power, is a leader in designing and manufacturing precision, programmable DC power supplies. Ranging from 30W to 150kW, Sorensen DC power supply products are used in R&D, test and measurement, process control, power bus simulation and power conditioning applications across a wide variety of industrial segments.
-
Product
PXI High Density Precision Resistor Module, 3-Channel, 3.5Ω to 1.51MΩ
40-298-144
Programmable Resistor Modules
The 40-298-144 is a high density programmable resistor module with 3 channels which can be set between 3.5Ω and 1.51MΩ with 2Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Synchro Power Amplifiers
SPA300
Amplifier
Computer Conversions Corporation
The SPA Series "Pulsating" Synchro Power Amplifiers are proven, high efficiency, low cost, compact, reliable solid state synchro drivers; designed for demanding Naval/Maritime, Aircraft, fire control and radar/Antenna related, applications. They are commonly used on synchro based data transmission, re-transmission, simulation and instantaneous absolute position indicating and active control systems.
-
Product
Test Engines
-
Verified Systems International GMBH
The test system cluster architecture is based on dual CPU or 4-CPU PCs acting as cluster nodes. The nodes communicate and synchronise over a high-speed network (Myrinet or InfiniBand). A modification of the Linux operating system allows to run the test execution and evaluation algorithms in hard real-time on reserved CPUs, where scheduling is non-preemptive and controlled by the test system itself. The interrupts caused by interfaces to the system under test may be relayed to CPUs designated explicitly for their handling. This approach offers the opportunity to utilise high-performance standard hardware and the services provided by the widely accepted Linux operating system in combination with all mechanisms required for hard real-time computing. The cluster architecture presents an opportunity to distribute interfaces with high data throughput on different nodes, so that PCI bus overload can be avoided. In addition, the CPU load can be balanced by allocating test data generators, environment simulations and checkers for the behaviour of the system under test ("test oracles") on dedicated CPUs.
-
Product
PXI/PXIe LVDT/RVDT Simulator Module, 2-Banks
43-670-103-AABBCC
Simulator
The 41/43-670-103 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types. It has two banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal.
-
Product
Channel Emulator
-
Qosmotec Software Solutions GmbH
Knowledge about channel models is not necessary to run tests with the QPER Channel Emulator. It applies the visualised virtual drive test concept, which is also used in the handover tester, to a fully fledged channel emulator: The tester outlines the network layout on the screen and defines a drive test route on the map. While running a simulated drive test, all channel effects are automatically calculated by QPER and applied to the channel emulation hardware.
-
Product
64-Channel 250kSa/s USB Modular Multifunction Data Acquisition
U2355A
Data Acquisition Module
The U2355A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2351A to simulate simultaneous analog input acquisition.
-
Product
PXI Automotive Switch Simulator Modules
-
Pickering's Switch Simulator Modules are designed for automotive test applications. These modules simulate the operation of automotive switches where dirty contacts or leaking current can be expected from switch contamination. They allow automotive I/O devices to be tested for correct operation under adverse conditions.
-
Product
ESD - Simulator
SESD 216
-
The test generator SESD 216 simulates electrostatic discharge as defined in the standard IEC / EN 61000-4-2. Depend on the Equipment Under Test (EUT) and the test set-up for laboratory tests the IEC standard shows two test methods
-
Product
UXG X-Series Agile Signal Generator, 10 MHz to 40 GHz
N5193A
Signal Generator
Get closer to reality: simulate increasingly complex signal environments for radar, EW & antenna-test Test sooner & increase confidence in EW systems by generating signal simulations when you need them: the UXG is a scalable threat simulator Use pulse descriptor words (PDWs) to generate long pulse trains & individually control pulse characteristics Accurately simulate multi-threat environments: 180-ns PDW update rate, chirps 10 to 25% of carrier frequency, pulses as narrow as 10 ns
-
Product
Mobile Comm DC Source w/ Battery Emulation
66321B
Battery Simulator
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66321B mobile communications dc source provides fast transient response, exceptional sourcing, output resistance programming, and precision measurement. This product is specially designed for testing next generation digital wireless communications products. The 66321B mobile communications dc source offers a new capability that simulates the internal resistance of a battery or battery pack. Additionally, these high performance models offer improved transient response and stable output operation with either short or long load leads.
-
Product
PXI-6711, 12-Bit, 4-Channel, 1 MS/s PXI Analog Output Module
777794-01
Analog Output Module
12-Bit, 4-Channel, 1 MS/s PXI Analog Output Module—The PXI‑6711 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response, power supply control, high-speed, deterministic control, and sensor/signal simulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6711 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
Product
NIBP Simulators
-
The full-featured SC-5 SimCube® NIBP Simulator provides ECG, Resp, Arrhythmias, Pacer Simulation, IBP, and more for accurate biomedical testing. The SimCube simulates real-life oscillometric pulses by varying both the shape and size of the wave as cuff pressure changes.
-
Product
Battery Simulator
-
The purpose of this battery impedance network (BNB) is to provide electric power to the device under test, providing a standard impedance. It has been developed for automotive tests. A resistor that emulates the internal battery resistance is implemented in the BNB.
-
Product
Vibration Test System
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Vibration Test System is a simulation of the various environments encountered in the manufacturing, assembly, transportation and use phases of execution. It is primarily used to identify the ability of a product to withstand environmental vibrations.
